OPERATION & PARTS MANUAL GloBug MODEL GB114BC LIGHTING SYSTEM (FOR USE WITH MQ SERIES GENERATORS) Revision #3 (03/22/06) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MULTIQUIP CORPORATE OFFICE 18910 Wilmington Ave. Carson, CA 90746 Email: mq@multiquip.com Internet: www.multiquip.com PARTS DEPARTMENT 800-427-1244 310-537-3700 MAYCO PARTS 800-306-2926 310-537-3700 SERVICE DEPARTMENT 800-478-1244 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 310-537-3700, EXT.
TABLE OF CONTENTS MQ GLOBUG LIGHTING SYSTEM Here's How To Get Help ............................................ 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation .................................... 8-11 Operation and Safety Decals ............................. 12-14 Specifications ..............................................
PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground ✓ FedEx or UPS Second Day or Third Day Note: Unless otherwise indicated by customer, all orders are treated as “Standard Orders”, and will ✓ FedEx or UPS Nex
GLOBUG LIGHTING SYSTEM — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the MQ GloBug Lighting System.
GLOBUG LIGHTING SYSTEM — SAFETY MESSAGE ALERT SYMBOLS CAUTION - Rotating Parts CAUTION - Equipment Damage Messages NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury. Other important messages are provided throughout this manual to help prevent damage to your lighting system, other property, or the surrounding environment.
GLOBUG LIGHTING SYSTEM — RULES FOR SAFE OPERATION WARNING - READ THIS MANUAL Failure to follow instructions in this manual may lead to Serious Injury or even Death. This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the GloBug Lighting System.
GLOBUG LIGHTING SYSTEM — RULES FOR SAFE OPERATION ■ ALWAYS make sure that the GloBug is secure on firm level ground so that it cannot slide or shift around, endangering workers. Also keep the immediate area free of bystanders. ■ ALWAYS keep area behind GloBug clear of people while raising and lowering mast. LIFTING/TRANSPORTING THE GLOBUG ■ ALWAYS use the lifting hanger, when lifting of the GloBug is required. ■ To prevent the GloBug from overturning, NEVER use in winds that exceed 22 mph(10m/s).
GLOBUG LIGHTING SYSTEM — RULES FOR SAFE OPERATION ■ When transporting the GloBug over smooth roads, place mast in stow position. Tighten the lamp adjustment lever and mast adapter set screw firmly to secure the balloon to the mast before transporting. This will prevent the balloon/light assembly from falling down or being damaged during transport. ■ When transportating the GloBug over rough terrain, remove the ballon/lamp assembly from the mast.
GLOBUG LIGHTING SYSTEM — RULES FOR SAFE OPERATION DANGER - GloBug Electric Shock Hazards ALWAYS keep electrical cords in good condition. Worn, bare or frayed wiring can cause electrical WET HANDS shock, thus causing Bodily Harm or even Death. NEVER grab or touch a live power cord with wet hands, the possibility exists of Electrical Shock, Electrocution, and even Death! ■ NEVER lubricate components or attempt service on a running GloBug.
GLOBUG LIGHTING SYSTEM — OPERATION AND SAFETY DECALS Machine Safety Decals The GloBug is equipped with a number of safety decals, Figures 1A through 1C. These decals are provided for operator safety and maintenance information. The illustrations below and on the next page show these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. Figure 1A.
GLOBUG LIGHTING SYSTEM — OPERATION AND SAFETY DECALS Figure 1B. Operation and Safety Decals (Continued) GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — OPERATION AND SAFETY DECALS Figure 1C. Operation and Safety Decals (Continued) PAGE 14 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — SPECIFICATIONS Table 1. Specifications GloBug Model GB114BC Input Voltage 120 VAC Frequency Max. Current Wind Stability with Generator Weight (less generator) 60 Hz Single-Phase 9.5 Amps 65 mph (80.46 kph) 243 lbs. (110 kg) Lamp Lamp Type Lumens (1)1000 Watt Metal Halidade 112,000 Light Coverage (360°) 150 ft. (45.72 meters) Surface Temperature (Longitudinal) 476.6°F (247°C) Max. Surface Temperature (Transversal) 417.2°F (214°C) Max. Fan Motor Balloon Fan Motor Max.
GLOBUG LIGHTING SYSTEM — DIMENSIONS Figure 2. Dimensions TABLE 2. DIMENSIONS Reference Letter Description Dimension ft. (mm.) Reference Letter Description Dimension ft. (mm.) A Wheel Base 2.66 ft. (811 mm.) F Max. Height (Mast Deployed Position) 16.41 ft. (5,004 mm.) B Height (Mast Stowed Position) 5.5 ft. (1,676 mm.) G Length (Front to Rear Wheel) 3.41 ft. (1,041 mm.) C Handle Height 2.91 ft. (889 mm.) H Length (Front Wheel to Outrigger) 4.83 ft. (1,473 mm.
GLOBUG LIGHTING SYSTEM — FLOODLIGHT FOOTCANDLE PLOT Based on 360°glare-free coverage. Figure 3. Floodlight Footcandle Plot (Bal120-Standard) GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — FLOODLIGHT FOOTCANDLE PLOT Based on 360°glare-free coverage. Figure 4. Floodlight Footcandle Plot (BAL120R-Reflector) PAGE 18 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — FLOODLIGHT FOOTCANDLE PLOT 360 degree coverage Figure 5. Floodlight Footcandle Plot (BAL-115D-Drum Shaped) GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — GENERAL INFORMATION The Multiquip GloBug Lighting System is a general purpose floodlight tower intended for emergency and remote lighting conditions. The GloBug can be powered by a variety of Multiquip's series generators. Power requirements for running the GloBug are 120 VAC, 60 Hz @ 9.5 amps. The GloBug can be powered by any MQ portable generator with an output of 2.9 kW or greater. The lighting system can be raised vertically in excess of 31.5 feet (9.
NOTE PAGE GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — COMPONENTS Figure 6. Major Components PAGE 22 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — COMPONENTS Figure 6 shows the location of the controls and components for the GloBug Lighting System. The functions of each control is described below: 1. Steering Handle – The GloBug can be moved in either a forward or reverse direction by pulling back or pushing forward on the T-handle. In addition the front wheels are designed to turn in the opposite direction of the T-handle placement thus allowing the GloBug to turn either left or right. 2.
GLOBUG LIGHTING SYSTEM — PRE-SETUP CAUTION - Read Manual Please read this entire manual carefully before attempting to operate the GloBug. Failure to read this manual could cause damage to the GloBug and serious injury to the operator. 3. Lift up on each outrigger (2) from its stow position, rotate backwards and place it in the deployed position, as shown in Figure 9.
GLOBUG LIGHTING SYSTEM — PRE-SETUP 5. To position the balloon, simply loosen the adjustment lever by turning it counterclockwise and either push down or up on the lever. Pushing down on the lever will cause the balloon to rise. Pushing up on the lever will allow the balloon to be lowered. See insert A in Figure 11. For circular positioning, swing the lever to the desired position. See insert B in Figure 11. 6.
GLOBUG LIGHTING SYSTEM — PRE-SETUP/OPERATION DANGER - HIGH VOLTAGE POWER LINES When raising mast, ALWAYS be on the lookout for overhead obstructions such as high voltage power lines. The possibility exists of electrocution, even death! if the GloBug comes in contact with high voltage power lines. Applying Power 1. Make sure the power ON/OFF switch (Figure 14) located near the bottom of the mast is in the OFF position. 4.
GLOBUG LIGHTING SYSTEM — SHUTDOWN Figure 18. Hot Lamp Surface 4. Using the mechanical winch (Figure 6, item 2), fully lower the mast. Turn winch handle counter-clockwise to Figure 21. Outriggers (Stow Position) lower mast. 5. Using the adjustment lever (Figure 6, item 22) place the 8. Press down on the top of the brake pedal (Figure 22) balloon/lamp assembly in the stow position. and hold, then release. This action will dis-engage the 6.
GLOBUG LIGHTING SYSTEM — MAINTENANCE CAUTION - READ SAFETY GUIDELINES Before performing any maintenance procedures, be sure to READ the lamp, balloon, and general safety guidelines in this manual. Failure to read and understand these safety guidelines could cause severe equipment damage and bodily harm. Removing the Lamp/Balloon Assembly 1. Place the lamp/ballon assembly in the STOW position. 2. With a 5 mm allen wrench, loosen the set screw (Figure 23) that secures the lamp to the mast adapter stand.
GLOBUG LIGHTING SYSTEM — MAINTENANCE Installing a New Lamp 1. When installing a new lamp (Figure 27) use only MQ recommended type lamp. See parts section of this manual. Failure to use correct type lamp could adversely affect lighting capability and may cause damage to the equipment. 2. Push down and hold the lamp holder (spring loaded) away from the lamp. Screw the lamp (turn clockwise) into the lamp socket. Gently place the lamp holder firmly over the top of the lamp.
GLOBUG LIGHTING SYSTEM — MAINTENANCE Check Cable Wear Removing the Hanger The wire rope (cable) that raises and extends the mast is a very important part of the GloBug lighting system. Following the procedure below when replacing wire rope (cable). 1. Remove the M12 x 40 bolt (Figure 32) from the hanger support assembly, then remove the hanger. Set hanger aside in a safe place where it will not get damaged.
GLOBUG LIGHTING SYSTEM — MAINTENANCE Pulling-Out the Mast Sections 1. Grab hold of the main mast (Figure 34) and begin pulling the mast sections upwards. Start with second mast, then the third mast and finally the fourth. 2. From the main mast, pull the winch cable wire to release the safety stopper pulley at the second mast. Figure 35. Cable Release Access Point 5.
GLOBUG LIGHTING SYSTEM — MAINTENANCE 5. Installation of Winch Cable 1. Route (pass) a new winch cable through the main mast 6. pulley (Figure 37). 2. Route the winch cable around the upper pulley of 7. the third mast section from back to front. 3. Next, route the winch cable around the lower pulley of the third mast section from back to front. 4. Route the winch cable around the upper pulley of the second mast section from back to front.
GLOBUG LIGHTING SYSTEM — MAINTENANCE Installation of Winch Ballast Box Removal 1. Reinstall the three retaining screws (Figure 31) and washers WARNING - HOT SURFACE (BALLAST) that secure the winch to the mast. Tighten screws between 24~ 33 ft-lbs. (33 ~ 45 N-m). Dangerous conditions exists inside the ballast 2. Install the four retaining screws and washers (Figure 31) that compartment. Please use extreme caution when performing maintenance on the ballast box. secure the winch cover. Tighten securely.
GLOBUG LIGHTING SYSTEM — MAINTENANCE Filter Replacement 5. Install a new filter over the brace as shown in Figure 43. Be sure to align the cut of the filter over the brace. WARNING - HOT SURFACE (LAMP FRAME) DO NOT replace filter immediately, allow a sufficient amount of time for the lamp assembly to cool down before changing filter. 1. Remove the balloon as described in the "Removing the Lamp/Balloon" section. 2. Disconnect the lamp power cable as shown in Figure 23. 3.
GLOBUG LIGHTING SYSTEM — MAINTENANCE (WIRING DIAGRAM) Figure 45. Wiring Diagram GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — MAINTENANCE PAGE 36 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — MAINTENANCE For a prolonged life cycle an extended quality follow the recommended GloBug service guidelines as referenced in Table 3. TABLE 3. PERIODIC CHECK AND MAINTENANCE FIGURE Lamp Balloon Mast Ca r t PART CHECK ITEM SOLUTION L1 Frame Pipe Frame pipe skewed? Replace. ❖ L2 Lamp Holder Lamp holder loose? Tighten or replace. ❖ L3 Lamp (Base) Lamp base loose? Screw in securely. ❖ L4 Lamp Defective lamp? Replace.
GLOBUG LIGHTING SYSTEM — TROUBLESHOOTING (LAMPS) Practically all breakdowns can be prevented by proper If the problem cannot be remedied, please leave the unit handling and maintenance inspections, but in the event of a just as it is and consult or company's service department. breakdown, please take a remedial action following the diagnosis based on the Lamp Troubleshooting (Table 4) information shown below. TABLE 4. LAMP TROUBLESHOOTING SYMPTOM Lamp does not light.
GLOBUG LIGHTING SYSTEM — TROUBLESHOOTING (MAST) Practically all breakdowns can be prevented by proper If the problem cannot be remedied, please leave the unit handling and maintenance inspections, but in the event of a just as it is and consult or company's service department. breakdown, please take a remedial action following the diagnosis based on the Mast Troubleshooting (Table 5) information shown below. TABLE 5. MAST TROUBLESHOOTING SYMPTOM Mast cannot be raised. Mast keeps coming down.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. NOTE Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. If more than one of the same reference number is listed, the last one listed indicates newest (or latest) part available.
GLOBUG LIGHTING SYSTEM — SPARE PARTS GloBug LIGHTING SYSTEM 1 TO 3 UNITS Qty. P/N Description 2 ......... E000009800 .... BULB 2 ......... A300033800 .... BALLAST/TRANSFORMER 2 ......... A300038400 .... CAPACITOR, 24 μF @480 VDC 2 ......... 1800001200 ..... BALLOON CLOTH 3 ......... A400038300 .... FILTER 200 (AIR) GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — NAMEPLATE AND DECALS PAGE 42 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — NAMEPLATE AND DECALS NAMEPLATE AND DECALS. NO. PART NO. PART NAME QTY. REMARKS 1 DCL413 DECAL; CAUTION COVER INFORMATION 1 2 DCL404 DECAL; CAUTION LAMP COVER BUZZER 1 3 DCL412 DECAL; WARNING, LIFT HANGER 1 4 DCL416 DECAL; DANGER, ELECTRICAL SHOCK HAZ.
GLOBUG LIGHTING SYSTEM — T-HANDLE ASSY. T-HANDLE ASSY. PAGE 44 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — T-HANDLE ASSY. T-HANDLE ASSY. NO. PART NO. 1 1102700130 * A200016500 2 3 0040730000 4 1503300130 5 A100012500 PART NAME QTY. REMARKS HANDLE GRIP 2 HANDLE GRIP ...............................................2 ........... INCLUDES ITEM W/ * SNAP RING (30) 1 SLEEVE BEARING (30dx34Dx20) 2 BASE PLATE 1 GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — STEERING ASSY. STEERING ASSY. PAGE 46 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — STEERING ASSY. STEERING ASSY. NO. PART NO.
GLOBUG LIGHTING SYSTEM — OUTRIGGER ASSY. OUTRIGGER ASSY. PAGE 48 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — OUTRIGGER ASSY. OUTRIGGER ASSY. NO. PART NO. 1 0010116090 2 A100011600 3 0010510025 4 1501160111 5 A200015302 6 A200015202 7 * 1641000330 8 0040110000 9 1501100430 10 0030210000 11 0040116000 12 0040216000 13 0030116000 14 2031321113 15 A100011500 16 2031320213 17 A400033400 PART NAME QTY. REMARKS BOLT (M16x90) 2 BRACKET (OUT,R) R 1 BOLT & WASHER (M10x25) 10 SPACER (OUT,R) 2 OUTRIGGER R ............................................ 1 ............. INCLUDES ITEM W/ * OUTRIGGER L ....
GLOBUG LIGHTING SYSTEM — MAST ADAPTER ASSY. MAST ADAPTER ASSY. PAGE 50 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — MAST ADAPTER ASSY. MAST ADAPTER ASSY. NO. PART NO. 1 2202390100 2 2202390111 * 3 * 2202500130 4 2202500230 5 1502280130 6 * 2202520110 1043002030 7 * 8 * 1043002130 9 * A400038800 10 0011808025 * 0011708010 11 * PART NAME QTY. REMARKS STAND ASSY. ................................................1 ...........
GLOBUG LIGHTING SYSTEM — MAIN MAST ASSY. MAIN MAST ASSY. PAGE 52 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — MAIN MAST ASSY. MAIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 MAST ASSY. PART NO. 0020305008 0010510025 1011000701 A100012401 0030112000 0040212000 0040112000 1642001430 1052001710 1711080130 0040112041 GB0010112040 0020304012 A200016801 2002500430 0020104020 1400200400 A300028800 PART NAME QTY. REMARKS SCREW AND WASHER 4 BOLT & WASHER (M10x25) 10 WINCH HM-G103 1 FIRST MAST 1 NUT (M12) 1 SPRING WASHER (M12) 1 WASHER (M12) 1 GROMMET 1 HANGER 1 SHACKLE 2 WASHER (12dx40Dx3.
GLOBUG LIGHTING SYSTEM — MAST SECTION ASSY. MAST SECTION ASSY. PAGE 54 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — MAST SECTION ASSY. MAST SECTION ASSY. NO. PART NO. 1 2072050112 2 2002262010 3 2082090112 4 2012263010 5 A300034300 6 0020204006 7 0020204010 8 1031040211 PART NAME QTY. REMARKS SECOND MAST 1 BRACKET (PULLEY) ................................1 ........... MAST SECTION 2 THIRD MAST 1 BRACKET (PULLEY) ................................1 ........... MAST SECTION 3 FOURTH MAST 1 SCREW (M4x6) 6 SCREW (M4x10) 6 WIRE (4Dx6300L) 1 GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — BASEPLATE COVER ASSY. BASEPLATE COVER ASSY. PAGE 56 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — BASEPLATE COVER ASSY. BASEPLATE COVER ASSY. NO. PART NO. 1 A200016100 2 A200017901 3 0011808025 4 A400041100 5 0010112025 6 0030110000 7 0040212000 8 0040112000 9 A300034600 10 E000010600 11 0010512020 12 0030152000 13 0040110000 14 0040210000 PART NAME COVER (BALLAST) CP GUARD (BALLAST) BUTTON SCREW & WASHER (M8x25) STOPPER BOLT (M12x25) NUT (M10) SPRING WASHER (M12) WASHER (M12) BRACKET CP SCREW (M10x25) BOLT & WASHER (M12x20) WING NUT (M12) WASHER (M10) SPRING WASHER (M10) QTY.
GLOBUG LIGHTING SYSTEM — BALLAST ASSY. BALLAST ASSY. PAGE 58 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — BALLAST ASSY. BALLAST ASSY. NO. PART NO. 1 A300038400 2 0020304012 3 A200018200 4 0010508025 5 A300033901 6 A300033800 7 A300035200 8 0020305090 9 0040105000 10 0030105000 PART NAME CAPACITOR, 24 μF @ 480 VDC SCREW & WASHER (M4x12) HOLDER BOLT & WASHER (M8x25) BALLAST HOLDER BALLAST (TRANSFORMER) CP CABLE (BALLAST) CP SCREW (M5x90) WASHER NUT QTY. 1 2 1 4 1 1 1 4 8 4 REMARKS GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — FAN BLOWER/LAMP BASE ASSY. FAN BLOWER/LAMP BASE ASSY. PAGE 60 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — FAN BLOWER/LAMP BASE ASSY. FAN BLOWER/LAMP BASE ASSY. NO. PART NO.
GLOBUG LIGHTING SYSTEM — BALLOON/LAMP GUARD ASSY. BALLOON/LAMP GUARD ASSY. PAGE 62 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
GLOBUG LIGHTING SYSTEM — BALLOON/LAMP GUARD ASSY. BALLOON/LAMP GUARD ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 1800001200 BALLOON CLOTH CP 1 2 0011808025 BUTTON SCREW & WASHER (M8 X 25) 8 3 A100013400 PRIMARY COVER.......................................... 1 .......... NO LONGER AVAILABLE 3A A100028600 BALLOON COVER ......................................... 1 .......... REPLACES P/N A100013400 S/N G10001 & ABOVE 3B A300060202 SEAL (TOP) ................................................... 1 ..........
Effective: October 1, 2002 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
NOTE PAGE GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV.
OPERATION & PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MULTIQUIP CORPORATE OFFICE 18910 Wilmington Ave. Carson, CA 90746 PARTS DEPARTMENT 800-427-1244 310-537-3700 MAYCO PARTS 800-306-2926 310-537-3700 SERVICE DEPARTMENT 800-478-1244 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 310-537-3700, EXT.
