PARTS AND OPERATION MANUAL PLASTER / MORTAR MIXERS © COPYRIGHT 2001, MULTIQUIP INC. EM-900S EM-900P Revision #7 (06/26/01) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-537-4259 E-mail:mq@multiquip.com • www:multiquip.
PAGE 2 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help .......................................... 3 Table Of Contents ................................................... 4 Parts Ordering Procedures ..................................... 5 Rules for Safe Operation & Safety Decals .............. 6 Warranty .................................................................. 7 ESSICK — 900S & 900P Operations ......................................................... 8-11 Specifications .........................................
PARTS ORDERING PROCEDURES n n n n n n n Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
RULES FOR SAFE OPERATION & SAFETY DECALS ■ Do not operate or service this equipment before reading the operating and maintenance instructions manual or serious injury may result. ■ Do not operate this equipment unless all guards and safety devices are attached and in place. ■ Stop the engine when leaving the equipment. ■ Block the unit when leaving or when using on a slope ■ Maintain this equipment in a safe operating condition at all times. ■ Caution must be exercised while servicing this equipment.
WARRANTY There are no warranties, express or implied, made by Multiquip Inc. hereunder on Products manufactured or distributed by it except the warranty against defects in material and workmanship on new Products to the original purchaser, as hereinafter set forth. Multiquip Inc. warrants Products manufactured by it to be free from defects in material and workmanship under normal and proper use and servicing for the periods specified on the bottom of this page.
EM-900S & 900P — OPERATIONS CONTROLS KILL SWITCH: (Gasoline Engine Only) Located on the side of the engine cover. ENGINE THROTTLE AND CHOKE CONTROLS: Please refer to the engine owners manual for specific instructions. The electric motor switch ( electric motor only) located on the motor — is used to start and stop the mixer. DUMP LATCH: To dump the tub, grasp the dump handle and lift the dump latch, then rotate the tub to discharge the mix. After, discharge, return the tub to the vertical mixing position.
EM-900S & 900P — OPERATIONS PADDLE SHAFT BEARING IMPORTANT — DRUM HEAD SEAL CARE The paddle shaft in the Essick Mixer rotates in sealed ball bearings requiring no additional lubrication. On each end of the mixing drum is a drum head containing self adjusting paddle shaft seals. These seals consist of packing rings, split glands and spring actuated adjusters. A properly maintained seal prevents material from working around the paddle shaft, causing excessive wear.
EM-900S & 900P — OPERATIONS TOWING — Before towing, check with local and state laws for proper compliance. The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction: Step 1. Insert the Draw Bar into the main frame. Secure, utilizing the ¾" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds. Step 2. Install the chain through the hole located between the frame gusset and frame angle.
EM-900S & 900P — OPERATIONS CLEANING — BLADE ADJUSTMENTS END SCRAPER Always disconnect the spark plug wire before cleaning the inside of the drum. Never pour or spray water over the gasoline engine or electric motor. For consistent performance, long life and high quality mixing, thoroughly clean the mixer inside and out at the end of each day’s operation.
EM-900S & 900P — SPECIFICATIONS EM-900S SPECIFICATIONS MODEL U.S.(inch) METRIC CAPACITY .................................................... 9 CUBIC FEET ....................................................... 248 LITERS BAG CAPACITY ............................................. 2½ - 3½ ............................................................ 2½ - 3½ WEIGHT (APPROX.) ....................................... 780 LBS. ............................................................. 395 KG. L X W X H .........
NOTE PAGE ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
EM-900S & 900P — SUGGESTED SPARE PARTS EM-900 S/P EM-900 S/P 1 to 3 Units 5+ Units Qty. P/N Description 3 ......... EM505834 ........... V-BELT 3 ......... 491115 ................ V-BELT, w/ELECTRIC MOTOR 6 ......... 491010 ................ LATCH w/ASSY 3 ......... EM200863 ........... BLADE KIT STEEL DRUM 3 ......... EM204625 ........... BLADE KIT POLY DRUM 12 ....... EM200301 ........... PACKING RING 4 ......... EM200794 ........... SPRING 4 ......... EM200286 ........... SPECIAL BOLT 1 .........
EM-900S & 900P — DRUM HEAD ASSEMBLY PAGE 16 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S & 900P — DRUM HEAD ASSEMBLY DRUM HEAD ASSEMBLY DRUM HEAD NO. PART NO. PART NAME 4 5 6 6 7 8 9 10 11 12 13 13 14 15 16 EM200018 EM902153 EM507720 500076 EM916019 EM200288 EM200286 EM200285 EM200303 EM200301 EM201648 EM507272 EM200794 EM200287 EM966048 COLLAR 1 BEARING 2 DUMP BEARING ..................................................................... 2 ................. STARTING S/N 98624090 DUMP BEARING ..................................................................... 2 .................
EM-900S, 900P — PADDLE SHAFT ASSEMBLY 46 47 48 49 61 58 59 60 TOW END PAGE 18 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S, 900P — PADDLE SHAFT ASSEMBLY PADDLE SHAFT ASSEMBLY NO. PART NO.
EM-900S — STEEL DRUM STEEL DRUM 109 110 111 108 PAGE 20 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S — STEEL DRUM STEEL DRUM NO. PART NO. 100# 101 101 101 102 103 104# 105# 106% EM201537 EPC-1 EBC-1 HBC-1 EM963580 EM969038 EM203332 EM507484 EM507765 EM507766 108 109 110 111 ❑ ❑ ❑ PART NAME QTY. REMARKS DUMP HANDLE 1 TOWING TONGUE (P. EYE) .................................... 1 .............. NO LONGER AVAILABLE TOWING TONGUE (PIN HOLE) .............................. 1 .............. CONTACT MQ SALES DEPT./ACCESSORY ITEM TOWING TONGUE (BALL HITCH) .......................... 1 ..............
EM-900P — POLYETHYLENE DRUM POLYETHYLENE DRUM 122 123 124 125 126 127 124 125 128 129 PAGE 22 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900P — POLYETHYLENE DRUM POLYETHYLENE DRUM NO. PART NO. PART NAME 115# 116 117# 118# 119# 120# 121 EM506310 EM506897 507416 507417 507517 509171 EM506896 EM509604 122 123 124 125 126 127 128 129 EM963610 EM969013 5041987 EM969079 505196 505066 492392 492584 PLASTIC DRUM W/O GRATES 1 SUPPORT REAR 1 STATIONARY GRATE 1 MOVEABLE GRATE 1 GRATE OPEN BAR 1 DUMP HANDLE 1 DRUM SUPPORT 1 DRUM & SHAFT ASSY (COMPLETE) (POLY) ........................ 1 ......................
EM-900S & 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLY CAB ASSEMBLY PAGE 24 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S & 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLY GAS ENGINES, PULLEYS & CAB ASSEMBLY COMMON PARTS NO. PART NO. PART NAME 150 151 152 153 154 155 156 157 158 159 167 168 169 170 171 EM507159 491010 EM505671 EM959080 EM102014 EM901515 EM905016 EM203098 3351 EM940734 502226 JISB2804C25 500214 EM010023 EM963064 CAB ASSEMBLY 1 LATCH ASSEMBLY ................................................. 2 .................. REPLACES 504744 DRIVE GEAR 16-½ DIA.
EM-900S & 900P — ELECTRIC MOTOR & PULLEYS CAB ASSEMBLY PAGE 26 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S & 900P — ELECTRIC MOTOR & PULLEYS ELECTRIC MOTOR & PULLEYS NO. PART NO. PART NAME 161 162 163 164 165 166 EM939315 EM505204 EM901513 491115 EM507490 EM507713 507715 ELECTRIC MOTOR 3.0 H.P 1 DRIVEN PULLEY 1 DRIVE PULLEY 1 V-BELT 2 THREADED ROD 1 IDLER ARM 1 GUIDE, V-BELT .................................................................................. 1 ................. NOT ILLUSTRATED QTY. REMARKS FOR COMMON PARTS SEE PAGE 25 ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S & 900P — AXLE & WHEEL GROUP PAGE 28 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
EM-900S & 900P — AXLE & WHEEL GROUP WHEEL GROUP EM-700 & 900 NO. PART NO. PART NAME 200 200 201 # 202 203 204 204 205 206 208 209 # 210 # 211 211# 212 # 213 213 EM507407 511334 3065 504708 507444 3068 8164 0183 3005 EM942000 3469 8115 EM903049 EM903113 EM903012 3504 EM941306 AXLE, RIGID ....................................... 1 .................... UP TO S/N 98960000 AXLE, RIGID ....................................... 1 .................... STARTING S/N 20800000 SEAL 2 THICK SPACER ....................
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 PAYMENT TERMS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
