Operation Manual

12
SONIC-Liner kit and SONIC-Liner complete model
Part No. off Description Material Dimensions
1 1 Fuselage / wing Moulded Elapor foam Ready made
2 1 Fuselage nose, top Moulded Elapor foam Ready made
3 1 Fuselage nose, bottom Moulded Elapor foam Ready made
4 1 Left wing panel Moulded Elapor foam Ready made
5 1 Right wing panel Moulded Elapor foam Ready made
6 1 Stabiliser (canard) Moulded Elapor foam Ready made
7 1 Left fin Moulded Elapor foam Ready made
8 1 Right fin Moulded Elapor foam Ready made
9 1 Left engine nacelle Moulded Elapor foam Ready made
10 1 Right engine nacelle Moulded Elapor foam Ready made
11 1 Fuselage joiner cover, left Moulded Elapor foam Ready made
12 1 Fuselage joiner cover, right Moulded Elapor foam Ready made
13 1 Wing joiner cover, left Moulded Elapor foam Ready made
14 1 Wing joiner cover, right Moulded Elapor foam Ready made
15 1 Fuselage top decking Moulded Elapor foam Ready made
16 1 Building instructions Paper, 80 g / m² A5
17 1 Decal sheet Printed adhesive film Ready made
Small parts set
20 4 Velcro tape, hook Plastic 25 x 60 mm
21 4 Velcro tape, loop Plastic 25 x 60 mm
22 6 Latch clip Inj. moulded plastic Ready made
23 6 Latch lug Inj. moulded plastic Ready made
24 4 Glue-fitting horn Inj. moulded plastic Ready made
25 4 Articulated connector housing Plastic Ready made
26 4 Articulated swivel block Metal Ready made 6 mm Ø
27 4 Countersunk screw Metal M1.6 x 4mm
28 4 Socket-head grubscrew (pushrod connector) Metal M3
29 1 Allen key Metal 1.5 A/F
30 1 Pushrod, V-bend Metal 1mm Ø
31 2 Pushrod, Z-bend Metal 1 Ø x 90mm
32 2 Wing joiner GRP 10 Ø x 7.5 x 210mm
33 1 Threaded sleeve, M4 clearance Inj. moulded plastic 12 Ø x 34 mm
34 1 Threaded bush Inj. moulded plastic M4 x 14 x 8.5mm Ø
35 1 Screw Plastic M4 x 40 mm
36 2 O-ring Rubber 36 Ø x 2 mm
RC fittings / power set (incl. 2 x Permax 400/6V)
40 2 Propeller Plastic 125 x 110mm
41 2 Motor Permax 400 6V Ready made
42 1 Connecting lead, complete with green plug Ready made
43 2 Electric motor suppressor set Ready made
50 3 Servo Tiny-S Ready made
51 1 Speed controller PiCO-Control 400 DUO Ready made
52 1 NiMH battery, 7/3000 mAh Ready made
53 1 Instructions Tiny-S servo Ready made
54 1 Instructions NiMH battery Ready made
55 1 Speed controller instructions PiCO-Control 400 DUO Ready made
56 2 Insulated ferrite ring, 14 x 9 x 5 Ready made
57 6 Heat-shrink sleeving Plastic, size 19 Ready made
58 2 UNI extension lead, 1200mm Ready made
59 2 Heat-shrink sleeving Plastic, size 32 10mm
Motor power leads
60 2 Flexible wire, 2 x 0.75mm² red/black 4/4 550mm
61 2 Heat-shrink sleeving, FT500 4.8/2.4 15mm
62 1 6-pin plug, complete, K4, assembled Ready made
Electric motor suppressor set
70 6 Kerko 47NF, R5 banded
71 2 ISO sleeve, 18mm long (0.8x 0.25)