Operation Manual

ROYAL evo 7 - Instructions
Page 39
ENGLIS
H
The “…+” mixer is set up in the main menu Mixer after
calling up a “…+” mixer (AILERON+ in our example ).
The mixer is then displayed, complete with all mixer in-
puts (Figs. 2 - 4).
What does the menu show? (Figs. 2 - 4)
Mixer inputs
The bottom five lines list the mixer inputs, i.e. the
transmitter controls which influence the movement of
the control surface in question.
Mixer values
The two columns to the right of the inputs show the
value for each mixer input (one or two values, depend-
ing on the mixer option of each mixer input). In this
menu only the displayed values can be altered.
Select the input to be changed. Press ENTER to move to
the first mixer value, which can then be altered. Pressing
ENTER again takes you to the second mixer value. Press-
ing ENTER once more concludes the adjustment process
for that mixer input.
“Dynamic overwriting”
Line 3 of the menu displays “dynamic” superimposed
information, depending on the mixer input at which the
cursor is currently located. This explains the current
mixer option in the form of a symbol, and the type of
mixer value.
Mixer switch
Column 4 indicates whether the mixer input in question
is switchable. If so, the switch and its current status are
displayed (example: I
Ð):
* (asterisk)  Mixer input = ON
Ð (arrow)  Shows the ON position of the switch,
if the switch is in the OFF position
15.4.3. Mixer options
™
“Symmetrical”
Neutral control setting: Centre
One parameter: Travels
100%
-100%
-100%
100%
Control
travel
Servo travel
Trv
š
“Asymmetrical“
Neutral control setting: Centre
Two parameters: TravelÏ and TravelÐ
100%
-100%
-100%
100%
Servo travel
Trv'
Trv#
Control
travel
œ
“Single-sided, with curve “
Neutral control setting: End-point
Two parameters: Pnt1 Point1, Pnt2 Point 2
100%
-100%
-100%
100%
Control
travel
Servo travel
Pt2
Pt1
›+
“Single-sided / linear with offset“
Neutral control setting: End-point
Two parameters: Offset and travel
100%
-100%
-100%
100%
Servo travel
Control
travel
Offs
Trv
Offs = 0%
Offs = -50%
15.5. The MixerA/B free mixers
for fixed-wing models and helicopters
Adjust. range
-100% ... OFF ... 100%
F
All mixer set-up values can be as-
signed to a 3D digi-adjustor
(Î 11.2.2.)
The free mixers (MixerA/B) can be used for special
mixer functions which are not covered by the “…+”
mixers. These two mixers are available for any model
(every model template), and are defined in the menu
Setup / MixerA/B, after which they appear auto-
matically in the current model in the
Mixer main menu,
where they then have to be activated and set up to suit
your specific application.
The control produces
symmetrical servo
movement with vari-
able travel.
Typical application:
aileron input in
AILERON+ mixer
The control produces
asymmetric servo
movement. The servo
travels can be set to
different values for
each direction.
Typical application:
flap input in
AI-
LERON+
mixer
The control produces
servo movement start-
ing from the end-point
of the control, with 2
points at ½ and full
control travel.
Typical application:
compensation input,
e.g. spoiler to ELE+
The control produces
linear servo move-ment
from its neutral posi-
tion, which can be
shifted using Offset.
Typical application:
spoiler input in
FLAP+
/ AILERON+
mixer,
for large down-travels
when butterfly / crow
braking is deployed.
Fig. 4
Dynamic overwriting:
Mixer value(s)
Mixer option (symbol)