Operation Manual

ROYAL evo 7
Page 2
15.3. Mixer: Ail.Diff 37
15.3.1. Parameter: Mode 37
15.3.2. Parameter: Diff. 37
15.4. The "...+" mixers 38
15.4.1. How the “...+” mixers work 38
15.4.2. How to set up “...+” mixers 38
15.4.3. Mixer options 39
15.5. The MixerA/B free mixers 39
15.5.1. Free mixer MixerA 40
15.5.2. Free mixer MixerB 40
15.6. Mixer: Gyro 40
15.6.1. Parameter: Mode 41
15.6.2. Parameter: Heading / Damping
(gyro gain) 41
15.6.3. Parameter: Suppression 41
15.7. Mixer: TAIL 42
15.7.1. Parameters: Coll.+ and Coll.- 42
15.7.2. Parameter: Yaw diff. 42
15.7.3. Parameter: Offset 42
15.7.4. Parameter: Zero point and
Collective Pitch display 43
15.8. Mixer: Rotor head
(electronic swashplate mixer / CCPM) 43
15.8.1. Parameter: Geometry 43
15.8.2. Parameter: Rotation 43
16. Main menu Servo K 44
16.1. Sub-menu Calibrate 44
16.1.1. Parameter: REV. (servo reverse) 45
16.1.2. Parameter: P1 … P5 45
16.2. Sub-menu: Assignment 46
16.2.1. Free assignment with fixed-wing models 46
16.2.2. Free assignment with model helicopters 47
16.2.3. Special features when assigning 47
16.3. Sub-menu: Monitor 47
16.4. Sub-menu: Test run 47
17. Main Menu Timer A 47
18. Main Menu Memory I 49
18.1. Sub-menu: Select model
(switch memories) 49
18.2. Sub-menu: Copy 49
18.3. Sub-menu: Erase 49
18.4. Sub-menu: Flight phases 50
18.4.1. Selecting names for flight phases 50
18.4.2. Blocking / releasing flight phases 50
18.4.3. Copying flight phases 50
18.5. Sub-menu: Properties 51
18.5.1. Parameter: Template 51
18.5.2. Parameter: Mode 51
18.5.3. Parameter: Assignment 51
18.5.4. Parameter: Throttle curve 51
18.5.5. Parameter: Shift 51
18.5.6. Parameter: Name 51
18.6. Sub-menu: New Model 52
18.6.1. Parameter: Memory No. 52
18.6.2. Parameter: Template 52
18.6.3. Parameter: Servo Config. 52
18.6.4. Parameter: Mode 52
18.6.5. Parameter: OK 52
19. Setting up a new model 53
19.1. Introduction 53
19.2. A new (fixed-wing) model
53
19.3. A new model helicopter
54
20. The model templates in detail 58
20.1. Template: BASIC1 59
20.1.1. Transmitter controls and switches 59
20.1.2. Servo assignment/receiver output sequence 59
20.1.3. Mixers 59
20.2. Template: BASIC2 60
20.2.1. Transmitter controls and switches 60
20.2.2. Servo assignment/receiver output sequence 60
20.2.3. Mixers 60
20.3. Template: ACRO 61
20.3.1. Transmitter controls and switches 61
20.3.2. Servo assignment/receiver output sequence 61
20.3.3. Mixers 62
20.4. Template: DELTA 63
20.4.1. Transmitter controls and switches 63
20.4.2. Servo assignment/receiver output sequence 63
20.4.3. Mixers 63
20.5. Template: GLIDER 64
20.5.1. Transmitter controls / switches 64
20.5.2. Servo assignment/receiver output sequence 64
20.5.3. Mixers 65
20.6. Template:4FLAPS 66
20.6.1. Transmitter controls / switches 66
20.6.2. Servo assignment/receiver output sequence 66
20.6.3. Mixers 67
20.7. Template: HELImech 69
20.7.1. Transmitter controls and switches 69
20.7.2. Servo assignment/receiver output sequence 70
20.8. Template: HELIccpm 70
20.8.1. Transmitter controls and switches 70
20.8.2. Servo assignment/receiver output sequence 70
21. Error messages 71
22. Accessories 71
22.1. HFM-4 crystal RF module 71
22.2. Channel-Check module
for HFM-4 crystal RF module 71
22.3. HFM-S Synthesizer RF module 71
22.4. Scanner
for HFM-S Synthesizer RF module 72
22.5. Trainer lead 72
22.6. Diagnosis lead 72
22.7. Other accessories, spareparts 72
23. PC interface 72
23.1. Software update / data back-up 72
23.2. Using a flight simulator 72
24. MULTInaut IV
channel expansion system 73
25. Care and maintenance 74
26. Advice and customer service 74