Operation Manual

Manual
33
Now use the 3-D digi-adjuster to select, for example,
the MPX-UNI configuration from those available:
¦New model
¨Exit
Memory nr. 3
Template 4 FLAPS
Servo conf. MPX-UNI_
Mode 4: è é
Assignment GLIDER
OK
Press the 3-D adjuster again to confirm your choice.
By selecting the 4 FLAPS template and the servo con-
figuration MPX-UNI you automatically set the following
receiver output sequence:
MPX-UNI
1 AILERON+
2 ELEVATR+
3 Rudder
4 Throttle
5 AILERON+
6 FLAP+
7 FLAP+
8 Spoiler
9 Spoiler
See also the illustration in (Î 12.2.7.).
12.2.5. Selecting the stick mode
The stick mode defines the association between the
stick axis and the controlled function. However, the
mode affects only the functions aileron, elevator and
rudder. The way in which throttle, spoiler and flap
are controlled is defined when you assign the transmit-
ter controls (Î Menu: L, Assignment, Controls).
First consider the functions you wish to control using
the left stick, then look up the appropriate mode in
the table below.
Mode table for the left stick:
Stick movements, left stick Required
forward/back left/right mode
Rudder
1: è é
Elevator
Aileron
3: è é
Rudder
2: é è
Throttle
(or Spoiler)
Aileron
4: è é
The double arrows following the mode code numbers
indicate where elevator (
è) and rudder (é) are lo-
cated.
The stick functions for the right stick are assigned
automatically.
Example: we will assume that you want elevator and
aileron on the left stick; in which case you would se-
lect Mode 3. Rudder is now automatically on the right
stick.
Turn the 3-D digi-adjuster to the right until the select
bar is over the Mode line, then press the 3-D digi-
adjuster:
¦New model
¨Exit
Memory nr. 3
Template 4 FLAPS
Servo conf. MPX-UNI
Mode 4: è é
Assignment GLIDER
OK
You can now use the 3-D digi-adjuster to select the
stick mode you have just decided to use.
Press the 3-D digi-adjuster to confirm your choice.
12.2.6. Selecting the Assignment
At this point you can select the assignment list, which
defines which transmitter controls and switches are
used to operate the various functions.
For a glider you would of course use the assignment
list bearing the name GLIDER (No. 2).
Turn the 3-D digi-adjuster to the right until the select
bar is over the Assignment line, then press the 3-D
digi-adjuster:
¦New model
¨Exit
Memory nr. 3
Template 4 FLAPS
Servo conf. MPX-UNI
Mode 4: è é
Assignment GLIDER__
OK
Select GLIDER from the five available assignments
using the 3-D digi-adjuster.
Press the 3-D digi-adjuster to confirm your selection.
Note:
You can also change the selected assignment in any
way at any time (Menu: ¡Setup, Assignment).
12.2.7. Confirming with OK
Rotate the 3-D digi-adjuster to the right until the select
bar is at the OK line, then press the 3-D digi-adjuster.
Congratulations!
You have successfully stored a new model in the
transmitter’s memory.
If you have kept to our suggestions in the steps com-
pleted thus far, the following data is now stored in the
new model memory:
a. Receiver output sequence
1
2
4
5
6
3
7
8
9
Spoiler
Spoiler
AILERON+
Throttle
AILERON+
ELEVATR+
Rudder
FLAP+
FLAP+
Fig. 12.2.7.1.: Servo assignment with MPX-UNI configuration