User Manual

ManualsBrandsMultiplex ManualsAircraftsTOMMY Jr. (White Red)

Accessories and tools

Before assembly

Use the list of components and

Fig. 1

to check completeness of the

components supplied.

We recommend using a soft, clean and at surface to ensure the model is

not damaged during assembly. Always use, unless otherwise specically

stated, ZACKI

-ELAPOR instant adhesive for gluing.

1. Completing the wings

Place the upper wing

as shown in

Fig. 2

on the clean and at

surface to ensure it is not damaged. Experimentally insert the canopy

into the pockets of the wing. This should be possible without having to

apply too much pressure. If this is not the case, minor adjustments to the

recesses for the carbon ber spars may be necessary. It is essential that

the canopy can be glued into the pockets fully and ush with the surface,

otherwise the correct installation angle difference will not be set. After

making sure everything ts properly, slightly roughen the contact surfaces

with sandpaper (240-320 grit), preferably also the exposed piece of the

carbon ber spar. Now apply sufcient adhesive to the contact surfaces

and insert the canopy rmly. Use a paper towel to wipe off any escaping

adhesive. Weigh down the canopy, e.g. with the ight battery, until the

adhesive has set fully. The bonded joint is very important and must,

therefore, be carried out carefully.

While the upper wing is setting, glue the wing struts

and

onto the

lower wing

Fig. 3

shows the installation direction, the procedure

is exactly the same as for the canopy; also ensure the bonded joint is

sufciently secure. When both components have set sufciently, join

them together. Place the upper wing as shown in

Fig. 4

on the surface

and perform all the work steps as usual. Make sure the components are

aligned properly to each other.

2. Gluing in the tailplane

In the next work step, the tailplane

is glued to the fuselage

; to do

so, please refer to

Fig. 5

. The process is the same as before; t together

without adhesive, roughen slightly, clean, apply ZACKI

, t together,

align properly. To check everything is correct, as shown in

Fig. 6

measure the distance from the wing tips of the tailplane to the recess of

the lower wing. The distance should be the same on both sides and the

tail should sit horizontally on the fuselage

Fig. 17

3. Gluing in the vertical tail

The procedure for gluing in the vertical tail is shown in

Fig. 7

. Here,

too, the respective work steps must be carried out carefully. During the

trial tting, the rear undercarriage can be experimentally pushed through

the hinge. It is now possible to carry out any reworking that might be

required. When gluing the tail, the rear undercarriage can be inserted

as a positioning aid. Take special care that ZACKI

does not come into

contact with the hinge. Use

Fig. 17

to check correct alignment of the tail

to the fuselage.

4. Installing the RC

Install the receiver in the model. To do so, use a piece of the supplied

hook and loop tape

⓰

. Ideally, the hook side is glued into the fuselage

and the loop side onto the receiver. The servos can now be connected.

The numbering facilitates assignment. In the next step, make sure your

transmitter is ready for operation. This involves assigning the channels

correctly and ensuring the trim is set to neutral.

Now insert the battery using a piece of hook and loop tape

⓰

Fig. 11

It is now time to bind your receiver. The servos can now be controlled and

should be set to neutral. Make sure the rods do not come into contact with

anything, thereby blocking the servos. As this could damage the servos.

Required accessories

• 1x Zacki2 Elapor

20g # 85 2727 or

• 1x Zacki2 Greentec 20g # 1-01293

• 1x ROXXY EVO Lipo 3-2600M 40C # 316656

• 1x receiver RX-6-DR light M-LINK 2.4 GHz # 5 5809

The following tools are required to assemble the model:

• 1x sheet of sandpaper (240-320 grit)

• Small cross-tip screwdriver (PH0)

• Possibly large cross-tip screwdriver

• Slotted screwdriver

• 10mm socket wrench

• 1.5mm hex wrench (included)

• If necessary, ZACKI

activator spray

Optional accessories

• 1x Hitec multi charger X1 red # 114131

• 1x lithium battery checker # 1-00957

• 1x Protect Pad charging mat # 763325

• 1x battery safe 10 # 763324

• 1x propeller balancer # 332355

Assembly instructions

Wingspan: 900 mm

Overall length: 930 mm

Flight weight: Approx. 1180 g

Wing area: 37.11 dm²

Wing loading: 31.8 g/dm²

RC functions: Aileron, elevator, rudder, motor

RR construction time: Approx. 45 min

Flight time: Approx. 6 min (3S-2600mAh)

Specications