Instructions

21
Parts List KIT Lentus # 1-00899 + RR Lentus # 1-00900
Power set (installed in RR version), available for KIT version as separate set # 1-01183
Reinforcements (tube, rod and longerons)
Plastic parts set (wings / fuselage + tail)
No. KIT RR Description Material Dimensions
80 0 1 LENTUS power set instructions
81 0 1 “Roxxy BL-Control 755 S-BEC” instructions
82 1 1 Washer Metal 8.4 mm I.D., 16 mm O.D.
83 1 1 Shakeproof washer Metal 8.4 I.D., M8
84 1 1 Nut Metal M8
85 2 2 Cheesehead screw Metal M3 x 20
86 2 2 Self-locking nut Metal M3
87 1 1 Mushroom-head screw Metal M2.5 x 12
88 0 4 Cheesehead screw Metal M3 x 6
89 1 1 Taper collet, complete Metal 5 mm O.D.
90 1 1 Propeller hub Injection-moulded plastic Ready made
91 1 1 Spinner Injection-moulded plastic Ready made
92 1 1 O-ring UV-resistant plastic 50 Ø x 1.5 mm
93 0 2 Folding propeller blade # 1-00106 for 3S hand-launch (standard) 11 x 7”
94 0 0 Folding propeller blade # 1-01970 for 4S ground take-off (option) 8 x 6”
95 0 1 BL speed controller ROXXY BL-755 S-BEC
96 0 4 Washer Metal 3.2 mm
97 0 1 BL outrunner motor ROXXY C 35-48-990kv
No. KIT RR Description Material Dimensions
70 1 1 Fuselage reinforcing tube (centre front) Rectangular GRP 9.85 x 273 mm
71 1 1 Fuselage reinforcing tube (tail) Round GRP 20 Ø x 750 mm
72 2 2 Fuselage stiffener (centre side) Rectangular GRP 5.5 x 3.5 x 250 mm
73 2 2 Fin strip (top rear, both sides) Rectangular CFRP 3.0 x 1.0 x 120 mm
74 1 1 Front side stiffener (L.H. + R.H.) Round GRP 2 Ø x 700 mm *
* length as supplied => shorten to: (*=> 2x Ø2 x 330 mm)
75 1 1 Top rear fuselage longeron Round GRP 2 Ø x 800 mm
76 1 1 CFRP strip (tailplane) Rectangular CFRP 6 x 1.5 x 400 mm
77 4 4 Aileron + ap stiffening tube Stainless steel tube 3 Ø x 400 mm
78 1 1 Rudder stiffening tube Stainless steel tube 3 Ø x 200 mm
No. KIT RR Description Material Dimensions
50 1 1 Flanged motor bulkhead Injection-moulded plastic Ready made
51 2 2 M6 connector holder, half-shell Ready made Injection-moulded plastic
52 1 1 Fin former Injection-moulded plastic Ready made
53 1 1 Tailwheel holder Injection-moulded plastic Ready made
54 3 3 Knuckle hinge lug Injection-moulded plastic Ready made
55 3 3 Knuckle hinge pivot Injection-moulded plastic Ready made
56 1 1 Tailplane spreader Injection-moulded plastic Ready made
57 1 1 Tailplane mount (for nuts) Injection-moulded plastic Ready made
58 1 1 Elevator horn Injection-moulded plastic Ready made
59 1 1 Tailwheel Plastic 32 mm Ø / 2.1 mm Ø bore
60 1 1 L.H. wing root rib Injection-moulded plastic Ready made
61 1 1 R.H. wing root rib Injection-moulded plastic Ready made
62 4 4 Wing retaining clip Injection-moulded plastic Ready made
63 1 1 Wing retaining bolt Injection-moulded plastic Ready made
64 2 2 Dummy wingtip wheel Injection-moulded plastic Ready made
65 2 2 L.H. servo shroud Injection-moulded plastic Ready made
66 2 2 R.H. servo shroud Injection-moulded plastic Ready made
EN