Installation Instructions

24
| Trinity user manual
8. Select the folder that contains the pictures.
9.
Select Start.
10
. The geotagged pictures are saved in the folder GeoTagged, a subfolder of the folder that contains the original pictures.
After saving the pictures on your computer, laptop or tablet it is recommended to delete the pictures from the SD card.
7.8 PAYLOAD
%DVHGRQWKHWKUHHVWDQGDUGSD\ORDGFRQƓJXUDWLRQVWKUHHSD\ORDGVDUHSUHVHWLQ4%DVH3OHDVHVHHFKDSWHUIRUWKH
WKUHHVWDQGDUGSD\ORDGFRQƓJXUDWLRQV
Creating a new camera
1. Select the Main Menu
in the top left corner.
2. Select Create Camera
.
3.
Select a camera name.
4.
Set camera settings.
The settings need to be obtained from the technical
VSHFLƓFDWLRQVRIWKHFDPHUD
5. Set default forward overlap.
6.
Set default side overlap.
7.
Set fastest trigger interval.
8. Select
to add the camera to the payload list.
9. If you wish to add another camera to the same payload
repeat steps 3. – 8.
10. Save the payload in the directory that is selected in settings (see chapter 7.10.1). The payload is automatically added to
the payload list in the Mission Template if it is saved in the payload directory that was selected in the QBase settings.
7.9 CREATING AN OFFLINE MAP
4%DVHRIIHUVWKHRSSRUWXQLW\WRZRUNZLWKRIŴLQHPDSVLQFDVH4%DVHLVQRWFRQQHFWHGWRWKHLQWHUQHW2IŴLQHPDSVFDQEH
FUHDWHGIURPDVHOHFWHGDUHD2IŴLQHPDSVDUHJHQHUDWHGEDVHGRQWKHLQIRUPDWLRQRIWKHRQOLQHPDSV'XULQJWKHFUHDWLRQ
process QBase needs to be connected to the internet.
Note:7KHODUJHUWKHVHOHFWHGDUHDRIDQRIŴLQHPDSLVWKHORQJHULWWDNHVWRJHQHUDWHLW
1.
Select the Main Menu
in the top left corner.
2. Select Create Map
.
3. Select Load Map.
4.
6HOHFWDQDUHDWKDW\RXZLVKWRFUHDWHWKHRIŴLQHPDSRI7KHRIŴLQHPDSLVFUHDWHGRIWKHFXUUHQWO\GLVSOD\HGDUHD
5. Choose the level of detail.
6. Select Estimate Cache SizeWRFDOFXODWHWKHVL]HRIWKHRIŴLQHPDS
7. Select Export Tiles
to create the map. The map is saved in the maps directory that is set in QBase settings (see chap-
WHU'HSHQGLQJRQWKHVL]HRIWKHƓOHLWPLJKWWDNHVRPHWLPHWRFUHDWHWKHRIŴLQHPDS
7.10 SETTINGS
7.10.1 Directory settings
:LWKWKHKHOSRIWKLVPHQXWKHGLUHFWRU\RIWKHRIŴLQHPDSVWKHXSGDWHVWKHPLVVLRQVDQGWKHSD\ORDGFDQEHVHW
1. Select the Main Menu
in the top left corner.
2. Select QBase
.
3.
Select Set Path to change the directories. The new path is automatically saved when the QBase User Interface is closed.
Click
to set directory to the default settings.
7 QBase – ground control station