Specifications

- Within 5 seconds after pressing “ON” button, fully
depress start button (when cathode comes into
contact with ozzle, the voltage will drop to
V , and release it slowly voltage in initialized arc
is between and V
Several seconds later a jet is supposed to appear
from torch nozzle while voltage will increase to
V
Set operating voltage to 160- V by turning
start button clockwise.
n 0-5
)(
20 80 ).
-
,
80 -160 .
- 170
Caution
If arc fails to form display reading remains at V , press start button again
within 5 seconds
If you fail to press the start button within the specified time, display reading will fall to
V and “OFF” LED will illuminate If that were to happen, repeat start procedure
press “ON” button and press start button
If a jet fails to form or an arc cannot be started deactivate torch
as specified in Sections .8 5.10 identify and troubleshoot failure Section .
Welding Procedure Modes
5. .1 MODE I Welding
Welding in this mode is similar to gas welding
Set appropriate MODE I current value as required based on metal thickness and
recommendations set forth in the Process Attachment Section
Prior to every indicator setting change by one step verify that voltage display reading is
between and V To increase voltage, turn start button clockwise, to reduce, turn
start button counterclockwise
Caution!
- Before using the cutting torch for welding
et the current for MODE I to 6 (if using 100-120V, set to 4), set the torch on the
torch holder (see ‘What’s Included’) and wait for the torch to automatically shut off.
!
- ( 200 - 350 )
.
-
000 .
().
-,
5 , , (see 7)
5.6 (2 )
6
.
( 8).
,
140 180 .
.
within 8 to 10 seconds
evaporate water performing Sections 5.2-5.5,
5.6.1. S
It is prohibited:
- to look inside nozzle to check for jet It is dangerous.!
5
25
-
.
Connect filler holder to grounding
connector on power supply rear
panel
5T
-
.
-
-.
(
200-350 ) (see igure)
.5 orch Start
buttons and select
position 4 of MODE I current indicator
Make certain that power supply ”OFF” LED is illuminated.
Depress and release “ON” button on power supply Make
certain that “ON” LED is on voltage reading will jump
briefly to V f .
5Press step-by-step the left or6
24
5
-
(50% 50% )
.
Take syringe (see "What's included") and fill with water/alcohol
mixture water and ethyl alcohol
- Open the filling neck cap.
- Insert the syringe into the filling neck holewhile pressing the
piston, fill until the torch starts to drip the water-ethanol
mixture from the nozzle. (see Figure)
- After filling, close the filling neck cap tightly and wipe torch
body dry
- Place the torch on the torch holder.
Caution!
-.
- While refueling, hold the torch with filling hole up and keep the nozzle level higher than
the filling hole
-.
Fill torch immediately prior to operations
Starting unfilled torch result damage
5. .
- 2.2-2.5 (
). 6.1, 1 - 3 6.6, 8 -
9.
- .
-
6.1 1- , 7)
( 6.6 1-3, -9).
4 Torch Setup and Servicing
Welding requires nozzle of diameter mm, i.e. 0,086-0,098 inches see ‘Spare
Parts Kit’ To replace nozzle follow Section Steps and Section Steps
Rotate torch start button to set it’s free movement to 2-3 mm (i.e 0,08-0,12 inches)
If it is not possible to set the free movement to 2-3 mm (i.e 0,08-0,12 inches),
disassemble torch (see Section , Steps 5 and adjust cathode assembly
position see Section , Step 6