ZONER16 1 6 ZO N E PAGI N G AN D BGM S W I T C H ER INS TA LLAT I ON AN D OP E RAT I ON M AN UAL
I M P O RTA N T SAF E TY INF ORMATION 1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 2. Read all documentation before operating your equipment. Retain all documentation for future reference. 3. Follow all instructions printed on unit chassis for proper operation. 4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 5.
INTRODUCTION AND CONTENTS The Zoner 16 is the entry level AMIS zoning product. A simple 16 zone output switcher with much more - providing remote paging facility, zone BGM enable buttons, LED BGM indication per active zone, zone output relays and separate BGM and paging inputs.
F R O N T PA N E L 1 1 BGM ON/OFF SWITCH These switches turn the BGM amplifier input ON or OFF to the corresponding ZONE OUTPUT 2 PAGING LEVEL This pot controls the level of the XLR output signal of the PAGING channel. It affects both the Paging Station and the Mic/Line XLR & RCA priority paging input. 4 5 3 4 5 5 POWER LED ON This LED indicates the unit is powered “on”.
R E A R PA N E L 10 9 10 8 7 6 BGM and PAGING IN 1 5 These pluggable terminal blocks connect the speaker outputs of the amplifiers used for the PAGING and BGM sources respectively. ZONE LOGIC OUT 2 This 25pin D-connector is used to control external devices. They can be used to drive relays for attenuator bypass. The outputs are open collector pull up, 24V 100mA drive. The total drive capacity is 150mA. This table shows an example of the possible combinations.
I N S TA L AT I O N E X A M P L E PA G E 6 A M I S Z O N E R 1 6 I N S TA L L AT I O N & O P E R AT I O N M A N U A L
INTERNAL ADJUSTMENTS & I N S TA L L AT I O N / T R O U B L E S H O O T I N G The only internal access required is for the installation of an Australian Monitor tone generator module. Installation is easy and is done by inserting the module onto the appropriate headers. INPUT CONNECTIONS For wiring balanced in, pin 2 is hot. Balanced input wiring (shielded pair cable) is recommended. Unbalanced RCA wiring should be keep as short as possible. Typically less than 3m.
Z 1 6 M PA G I N G S TAT I O N INTRODUCTION CONTROLS The Australian Monitor Installation Series Zoner16M Paging Station is a 16 zone paging station complete with a slimline gooseneck paging microphone. The Paging station is designed to be used with the Zoner16 Zone Switching System and will allow paging into any individual zone, any combination of zones or All Call to all zones. LED indicators provide the user with visual feedback of the zones being paged or if the priority local paging All Call is busy.
DIMENSIONS A M I S Z O N E R 1 6 I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 9
BLOCK DIAGRAM PA G E 1 0 A M I S Z O N E R 1 6 I N S TA L L AT I O N & O P E R AT I O N M A N U A L
S P E C I F I C AT I O N S FREQUENCY RESPONSE 20Hz - 20kHz (+0,-3dB) TOTAL HARMONIC DISTORTION < 0.1% @ 1kHz SIGNAL TO NOISE RATIO > 90dB (all pots at centre position) CROSSTALK BETWEEN CHANNELS >70dB SENSITIVITY (TRIM IN CENTRE 0 dB) Line Sens 0.
AUSTRALIA AND NEW ZEALAND w w w. a u s t r a l i a n m o n i t o r. c o m . a u SYDNEY MELBOURNE BRISBANE ADELAIDE PERTH AUCKLAND (NSW & ACT SALES) (VIC & TAS SALES) (QLD SALES) (SA & NT SALES) (WA SALES) (NZ SALES) 1 Clyde Street Silverwater NSW 2128 Private Bag 149 Silverwater NSW 1811 Phone: (02) 9647 1411 Fax: (02) 9648 3698 Email: nsw@audiotelex.com.
