Product Manual

CHECKLIST UPON RECIEPT OF GOODS
1) Inspect for any damage that may have occurred in transit,
report any damage within 48 hours.
2) Check all bolts, screws, set screws etc. for looseness, and
retighten as required.
3) Before installing rotate the blade to be sure it does not rub.
Adjust as required.
4) Before installation please read the entire information sheet
carefully.
GENERAL SAFTEY INFORMATION
WARNING– TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING.
1) Use this unit only in the manner intended by the manufacturer. If you have
any questions, contact the manufacturer.
2) Before servicing or cleaning the unit, switch the power off at the service
panel and lock the service panel to prevent the power from being switched
on accidentally. When the service disconnect can not be locked, securely
fasten prominent warning device, such as a tag to the service panel.
3) Follow all electrical and safety codes as well as National Electric Code
(NEC) and the Occupational Safety and Health Act (OSHA).
4) Motor must be securely and adequately grounded.
5) All moving parts should be guarded.
6) When cleaning electrical equipment always use an approved cleaning
FOLLOW INSTALLATION INSTRUCTIONS CAREFULLY
DO NOT TAKE SHORT CUTS
DISCLAIMER
The warranties contained herein are made expressly in view of any and all other warranties expressed or implied. The liability of the seller is limited to the
repair or replacement of any product which does not conform to the warranties expressly provided herein.
LIMITIED WARRANTY
MF Flex fans are warranted by Vostermans Ventilation Inc., to the original user, against defects in workmanship on materials, under normal use and
service (rental use excluded) for the indicated period of guarantee after date of purchase. Any part which is determined to be defective in material or
workmanship should be returned to the dealer from whom it was purchased. All shipping cost will be paid by the customer unless arranged differently
prior to return. Parts will be repaired or replaced at the dealers discretion.
GUIDELINES FOR INSTALLATION
1) Installation work and electrical wiring must be done by qualified persons in
accordance with all applicable codes and standards, including fire-rated
construction.
2) The unit should be securely mounted in a rigid framework. Note: allowing
the fan frame to flex or move will result in undue vibrations and possible
pre-mature motor or fan blade failure.
3) Connect the power to the motor using an approved wiring method.
4) Before activating the fan, double check to ensure that there are no obstruc-
tions (framing, packaging, debris, cord) which could interfere with proper
fan operation.
5) Ensure proper installation/removal of condensation plug—see diagram.
6) Use liquid tight fittings and conduit.
7) When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
8) If fan is used to inflate advertising tubes ensure placement will not interfere
with traffic flow, hinder visibility or come in contact with overhead power
lines.
Use limitations
1) Verify fan/motor is capable of variable speed operation before attaching
speed control devices.
2) Installation instructions for fan and controller must be followed carefully.
All warranty rights and conditions are considered null and void when a low
quality controller is used.
3) Air supply and temperature. Sufficient air supply over the motor must be
assured in all circumstances. Limits of operating ambient temperatures are
15 to 112 degrees F ( -19 to 45 C).
4) Industrial restrictions on Polypropylene blades apply. Use with certain
chemicals is unsuitable or not recommended—the following is a partial list
for guideline purposes.
Restrictions on Polypropylene Blades (not Recommended)
Chloro-Sulphonic acid mixtures of HN03-H2SO4 Chloroform
Mixture of HNO3-HCL Esters 1:2 Dichloroethylene
Nitric Acid Benzene Trichloroethylene
Sulphuric acid, fuming Gasoline Diethyl Ether
Carbon Tetracholride Toluene Liquid Chlorine
Chlorobenzene Xylene