User Guide

APPLICATION LIMITATIONS
D
o not apply if wall board surface temperature is below 50°F, or
o
ver 100°F. Do not apply if ambient temperature is less than 50°F
and falling, over 100°F and rising, or if precipitation or extreme
high humidity is expected within a 12-hour period.
PACKAGING AND STORAGE
SMOOTH PRIMED FIBERCEMENT SIDING - 4’ wide x 8, 9, 10 or
1
2 ft. Lengths
STANDARD THICKNESS - 5/16” – Special Order 7/16”
MULTICOAT STUCCO MIX - 5-Gal. Pails
MULTICOAT ELASTOMERIC JOINT TAPE - 3” & 6” widths 100 ft. rolls
POLYURETHANE CAULK - Tubes
Store at 40 –90°F. Shelf life is approximately 24 months in
unopened pails.
WARRANTY
Materials are guaranteed with respect to uniformity and quality
within manufacturers’ specifications. Seller makes no other
w
arranty, expressed or implied, regarding the use of its products.
Since use of the products is beyond seller’s control, the buyer
a
ssumes all risks of use. Seller’s sole obligation shall be to replace
material if found to be defective. Seller shall not be liable for any
l
oss, direct or consequential, resulting from use of its products.
TEST DATA –STUCCO MIX
TEST DATA –CEMENTITIOUS WALL BOARD
TEST TYPE TEST METHOD RESULTS
2000 Hour Weatherometer . . . . . . .ASTM G-23 No marked evidence of surface cracking, blistering, flaking, chalking,
crazing or any other deleterious ef
fects obser
ved
Moisture Resistance . . . . . . . . . . . .ASTM D2247 No blistering or cracking of surface
Freeze-Thaw . . . . . . . . . . . . . . . . . .Section VI D of acceptance No change in color, no cracks, no crazing, no delamination
criteria for EIFS
Abrasion Test (Falling Sand) . . . . . .ASTM DE968 Method A Initial wear started at 3200 liters
Fungus . . . . . . . . . . . . . . . . . . . . . .Mil-Std-810B (Method 508) Passed
Moisture Vapor Transmission . . . . .ASTM E96 4.56 Perms, the coating is not a vapor barrier
Thicknesses: 1/4", 5/16" & 7/16"
Installed Weight:
1/4" thick 1.9 lbs/sq.ft.
5/16" thick 2.4 lbs/sq.ft.
7/16" thick 3.3 lbs/sq.ft.
Density: 86 lbs/cu.ft.
Bending Strength:
Transversal: 2,000 psi
Longitudinal: 2,500 psi
Thermal Resistance: R=0.17
Shrinking: Ambient to oven-dry: 0.06%
Swelling of Thickness
(after 7 days of full saturation): 0.2%
Flame Spread: 0
Smoke Density: 0
Wind Pressures:
Shear
V
alues:
ICC/ES Report #5139 SBCCI Report #9556
FOAM OR MIX PANEL
A
TTACHED OR GLUED
TO TOP SHEET ONLY
P
RIMED FIBERCEMENT PANEL
ADHESIVE
1/8" GAP
3
/8" CLEAR
HORIZONTAL
E
XPANSION
J
OINT REVEAL
T
OP PLATE 2' X 4'
P
RIMED FIBERCEMENT PANEL
NAILED TO TOP
PLATE, FLOATING
ON JOIST AND FLOOR
PRIMED FIBERCEMENT P
ANEL
SMOOTH
1
.8" GAP
3
/8" CLEAR
HORIZONT
AL
EXPANSION
JOINT REVEAL
PRIMED FIBERCEMENT
P
ANEL
N
AILED TO
T
OP PLA
T
E,
F
LOA
TING
ON JOIST
A
ND FLOOR
S
TUD 2' X 4'
B
OTTOM PLATE
2' X 4'
FLOORING
FLOOR JOIST
2
' X 6'
S
TUD 2' X 4'
S
TUD 2' X 4'
B
OTTOM PLA
T
E
2
' X 4'
FLOORING
F
LOOR JOIST 2' X 6'
TOP PLA
TE 2' X 4'
Tape and joining system
b
y coating applicator
S
traight Joint Detail
E
xternal Corner Detail
Internal Corner Detail
P
rimed Fibercement Panel
R
einforcing tape
M
ulticoat
Stucco Mix
Sealant
Internal Corner
Primed Fiber
c
ement Panel
3/16" gap
External Corner
Primed Fibercement Panel
e
dges
1/8" gap
Straight Joint
P
rimed Fibercement Panel
E
xternal
Corner
Bead
External
Bullnose
Corner Bead
Outside Cor
ner (Optional)
Primed Fiber
cement Panel
F
inish
F
oundation
W
eep Screed 3/8"
2'
Primed Fibercement Panel
Tape and joining system
by coating applicator
Multicoat Stucco Mix
Multicoat Stucco
Mix over Primed
Fibercement Panel
Primed
Fibercement
P
anel
Outside Corner (Optional)
P
rimed
F
ibercement
P
anel
The Coating of the Future…Today
MC0406
MULTICOAT
®
CORPORATION
West Coast
Toll Free: [phone]
[phone] F
ax [phone]
Website: www.multicoat.com
E-mail: info@m
ulticoat.com
MULTICOAT
®
PRODUCTS, INC.
East Coast
Toll Free: [phone]
[phone] F
ax [phone]
Website: www.multicoat.com
E-mail:
inf
o@m
ulticoat.com
Available Through: