User's Manual
Table Of Contents
- _
- Contents
- Chapter 1 - Introduction
- _
- Front Panel
- Front Panel Description
- Back Panel
- Back Panel Description
- Typical Applications
- Connecting a Remote Site via Cable Modem
- Connecting a Local Site to the Internet
- Specifications
- Chapter 2 - Hardware Installation
- Hardware Installation
- Safety
- Unpacking the RF802EW
- Cabling
- Chapter 3 - Software Installation and Configuration
- Software Installation and Configuration
- Software Installation
- Using RouteFinder Setup Wizard
- Testing your Connection
- Chapter 4 - Telnet
- Using Telnet to Configure your RouteFinder
- Chapter 5 - RouteFinder Manager
- RouteFinder Manager
- General Settings
- WAN Ethernet Segment
- Async Port
- Remote Access-Remote Access Settings
- Enable IP Mapping - Virtual Server
- Port Settings
- Edit Login Script for Remote Access
- Writing a login script for IP Routing
- Modem String Settings
- LAN DHCP Server
- Routing Settings
- Routing Table
- Filter Settings
- Wireless Settings
- Refresh Device List
- Device Name and Password
- Save Settings to File
- Load Settings
- Upgrade Firmware
- General Diagnostic
- Chapter 6 - RouteFinder Monitor
- RouteFinder Monitor
- Running RouteFinder Monitor
- Refresh Device List
- Test Connection
- Terminate Connection
- Save to File
- Save Now
- Autosave
- IP Address/Name
- Event Messages
- TCP/IP Tab
- Time Tab
- Status Tab
- Statistics Tab
- Chapter 7 - LAN Client Settings
- LAN Client Settings
- Setting up Remote Access Clients
- Accessing a Windows NT Server
- Accessing a Novell Server
- Accessing a Windows NT Server and a Novell NetWare Server
- Accessing a Unix Server
- Make New Connection (Windows 2000 only)
- Chapter 8 LAN-to-LAN Settings
- LAN-to-LAN Settings
- Setting up LAN-to-LAN Routing
- Using the Find Computer command
- Using LMHosts
- Chapter 9 - Troubleshooting
- Troubleshooting
- Common Problems
- Chapter 10 - Service, Warranty and Technical Support
- Introduction
- Limited Warranty
- Addendum for North American Products
- Addendum for International Products
- Out of Warranty Repair Costs
- Software User License Agreement
- Technical Support
- Contacting Technical Support
- Recording RouteFinder Information
- Online Warranty Registration
- About the Internet
- Ordering Accessories
- Appendixes
- Appendix A - Regulatory Compliance Information
- Class B Statement FCC Part 15
- Appendix B - Tools for your RF802EW
- RouteFinder Monitor
- PING
- WINIPCFG and IPCONFIG
- TRACERT
- Appendix C - Cabling Diagrams
- Glossary
- Index
49
Chapter 5 - RouteFinder Manager
Routing Table
The routing table stores the routing information so that the RF802EW knows how to route the IP
packets to the proper network.
WAN Ethernet 192.168.3.1
LAN Ethernet 192.168.5.1
WAN Ethernet 192.168.5.254
LAN Ethernet 172.168.2.254
PC 2
172.168.2.1
PC 1
192.168.3.9
RF802EW-1
RF802EW-2
What is the purpose of the routing table?
In the diagram above, the RF802EW-1 has the routing information to route between 192.168.3.x
and 192.168.5.x. The device does not have the information about how to route to the 172.168.2.x
network. If you want the RF802EW-1 to route to 172.168.2.x, you must add the following
information to the routing table:
IP: 172.168.2.0
Network: 255.255.255.0
Gateway IP: 192.168.5.254
Interface: Ethernet (Local Network)
If you would like the RF802EW-2. to route to 192.168.3.x, enter the following routing table
information into the RF802EW Routing settings:
IP: 192.168.3.0
Network: 255.255.255.0
Gateway IP: 192.168.5.1
Interface: WAN Ethernet