User's Manual
Table Of Contents
- _
- Contents
- Chapter 1 - Introduction
- _
- Front Panel
- Front Panel Description
- Back Panel
- Back Panel Description
- Typical Applications
- Connecting a Remote Site via Cable Modem
- Connecting a Local Site to the Internet
- Specifications
- Chapter 2 - Hardware Installation
- Hardware Installation
- Safety
- Unpacking the RF802EW
- Cabling
- Chapter 3 - Software Installation and Configuration
- Software Installation and Configuration
- Software Installation
- Using RouteFinder Setup Wizard
- Testing your Connection
- Chapter 4 - Telnet
- Using Telnet to Configure your RouteFinder
- Chapter 5 - RouteFinder Manager
- RouteFinder Manager
- General Settings
- WAN Ethernet Segment
- Async Port
- Remote Access-Remote Access Settings
- Enable IP Mapping - Virtual Server
- Port Settings
- Edit Login Script for Remote Access
- Writing a login script for IP Routing
- Modem String Settings
- LAN DHCP Server
- Routing Settings
- Routing Table
- Filter Settings
- Wireless Settings
- Refresh Device List
- Device Name and Password
- Save Settings to File
- Load Settings
- Upgrade Firmware
- General Diagnostic
- Chapter 6 - RouteFinder Monitor
- RouteFinder Monitor
- Running RouteFinder Monitor
- Refresh Device List
- Test Connection
- Terminate Connection
- Save to File
- Save Now
- Autosave
- IP Address/Name
- Event Messages
- TCP/IP Tab
- Time Tab
- Status Tab
- Statistics Tab
- Chapter 7 - LAN Client Settings
- LAN Client Settings
- Setting up Remote Access Clients
- Accessing a Windows NT Server
- Accessing a Novell Server
- Accessing a Windows NT Server and a Novell NetWare Server
- Accessing a Unix Server
- Make New Connection (Windows 2000 only)
- Chapter 8 LAN-to-LAN Settings
- LAN-to-LAN Settings
- Setting up LAN-to-LAN Routing
- Using the Find Computer command
- Using LMHosts
- Chapter 9 - Troubleshooting
- Troubleshooting
- Common Problems
- Chapter 10 - Service, Warranty and Technical Support
- Introduction
- Limited Warranty
- Addendum for North American Products
- Addendum for International Products
- Out of Warranty Repair Costs
- Software User License Agreement
- Technical Support
- Contacting Technical Support
- Recording RouteFinder Information
- Online Warranty Registration
- About the Internet
- Ordering Accessories
- Appendixes
- Appendix A - Regulatory Compliance Information
- Class B Statement FCC Part 15
- Appendix B - Tools for your RF802EW
- RouteFinder Monitor
- PING
- WINIPCFG and IPCONFIG
- TRACERT
- Appendix C - Cabling Diagrams
- Glossary
- Index
41
Chapter 5 - RouteFinder Manager
Enable IP Mapping - Virtual Server
IP Mapping is available only when NAT is enabled. If NAT is enabled for a particular port, that port is
firewall protected. The Enable IP Mapping function allows you to open a “hole” in your firewall to
allow access to your LAN via the Internet. For example, you can use the IP mapping function to
access an FTP server on your LAN via the Internet. IP Mapping is most suitable to fixed or static IP
addressing.
1. To enable IP Mapping, from the General Settings dialog box, select Enable IP Mapping, then
click IP Mapping (Virtual Server).
2. The Virtual Server Mapping dialog box displays.
For each service you want to set up:
1. Select either the WAN or Async (Serial) port from the Port No list.
2. Enter the External IP address supplied by your ISP. If your ISP uses dynamic IP addressing,
enter 0.0.0.0. Your device will use the dynamically assigned address when connecting to your
ISP.
3. Enter the TCP/IP port number for the service that you will be using for IP mapping. Common
TCP/IP port numbers are listed below:
WWW Port 80
FTP Port 20 or 21
SMTP Port 25
POP3 Port 110
If you would like to map all services for this external IP address to a computer on your LAN, you
can enter port number 0. This means that whenever anyone accesses your external IP address,
they will automatically be “mapped” to the internal computer that you specify, regardless of what
port number they are using.
4. Enter the Internal IP address of the server to which you want to map the External IP address.
5. Enter the port number for the service that you will be using for this IP mapping.
Click Insert to include the mapping.
6. Click OK when you have completed mapping addresses.
Note: IP Mapping function allows you to have only one port service on your LAN. For example, if
you map an external IP (16.895.1.3) to an internal IP address (192.168.2.22 - a www server),
only the internal IP address in your local network can serve as the www.server for the external IP
address.