User's Manual
Table Of Contents
- _
- Contents
- Chapter 1 - Introduction
- _
- Front Panel
- Front Panel Description
- Back Panel
- Back Panel Description
- Typical Applications
- Connecting a Remote Site via Cable Modem
- Connecting a Local Site to the Internet
- Specifications
- Chapter 2 - Hardware Installation
- Hardware Installation
- Safety
- Unpacking the RF802EW
- Cabling
- Chapter 3 - Software Installation and Configuration
- Software Installation and Configuration
- Software Installation
- Using RouteFinder Setup Wizard
- Testing your Connection
- Chapter 4 - Telnet
- Using Telnet to Configure your RouteFinder
- Chapter 5 - RouteFinder Manager
- RouteFinder Manager
- General Settings
- WAN Ethernet Segment
- Async Port
- Remote Access-Remote Access Settings
- Enable IP Mapping - Virtual Server
- Port Settings
- Edit Login Script for Remote Access
- Writing a login script for IP Routing
- Modem String Settings
- LAN DHCP Server
- Routing Settings
- Routing Table
- Filter Settings
- Wireless Settings
- Refresh Device List
- Device Name and Password
- Save Settings to File
- Load Settings
- Upgrade Firmware
- General Diagnostic
- Chapter 6 - RouteFinder Monitor
- RouteFinder Monitor
- Running RouteFinder Monitor
- Refresh Device List
- Test Connection
- Terminate Connection
- Save to File
- Save Now
- Autosave
- IP Address/Name
- Event Messages
- TCP/IP Tab
- Time Tab
- Status Tab
- Statistics Tab
- Chapter 7 - LAN Client Settings
- LAN Client Settings
- Setting up Remote Access Clients
- Accessing a Windows NT Server
- Accessing a Novell Server
- Accessing a Windows NT Server and a Novell NetWare Server
- Accessing a Unix Server
- Make New Connection (Windows 2000 only)
- Chapter 8 LAN-to-LAN Settings
- LAN-to-LAN Settings
- Setting up LAN-to-LAN Routing
- Using the Find Computer command
- Using LMHosts
- Chapter 9 - Troubleshooting
- Troubleshooting
- Common Problems
- Chapter 10 - Service, Warranty and Technical Support
- Introduction
- Limited Warranty
- Addendum for North American Products
- Addendum for International Products
- Out of Warranty Repair Costs
- Software User License Agreement
- Technical Support
- Contacting Technical Support
- Recording RouteFinder Information
- Online Warranty Registration
- About the Internet
- Ordering Accessories
- Appendixes
- Appendix A - Regulatory Compliance Information
- Class B Statement FCC Part 15
- Appendix B - Tools for your RF802EW
- RouteFinder Monitor
- PING
- WINIPCFG and IPCONFIG
- TRACERT
- Appendix C - Cabling Diagrams
- Glossary
- Index
17
Chapter 3 - Software Installation and Configuration
Record the values presented in the Device Information panel for later reference.
Device IP Address ______________________
Device MAC Address ____________________
Device Firmware Version _________________
Click Next.
Note: If a message appears indicating the device is not found, or you do not see the device
you are attempting to configure listed, click Refresh Device List.
6. The Setup Wizard: Device IP Address dialog box displays.
• Enter your local internal network’s IP address for this device.
The Setup Wizard will automatically detect the first three octets of your local IP address. You
must enter the last octet only.
• If you wish, you can change the network name of your RouteFinder. If your ISP requires
your device to have a name, you may use the name entered here.
• Click Next to continue. The device will search the network to ensure that the IP address is
valid. This may take several seconds.
Note: If your ISP provided you with an IP address, do not enter that address. Enter the IP
address for this device on your local network. Refer to the Glossary for additional
information on IP addressing.
7. The Wireless Function dialog box displays.
Select the function for the wireless port function by selecting Enable Wireless Access Point
function only, or Enable Wireless Access Point + Router function. If you are using NAT
Enabled, you may also select Enable PPPoE.