User's Manual
Table Of Contents
- _
- Contents
- Chapter 1 - Introduction
- _
- Front Panel
- Front Panel Description
- Back Panel
- Back Panel Description
- Typical Applications
- Connecting a Remote Site via Cable Modem
- Connecting a Local Site to the Internet
- Specifications
- Chapter 2 - Hardware Installation
- Hardware Installation
- Safety
- Unpacking the RF802EW
- Cabling
- Chapter 3 - Software Installation and Configuration
- Software Installation and Configuration
- Software Installation
- Using RouteFinder Setup Wizard
- Testing your Connection
- Chapter 4 - Telnet
- Using Telnet to Configure your RouteFinder
- Chapter 5 - RouteFinder Manager
- RouteFinder Manager
- General Settings
- WAN Ethernet Segment
- Async Port
- Remote Access-Remote Access Settings
- Enable IP Mapping - Virtual Server
- Port Settings
- Edit Login Script for Remote Access
- Writing a login script for IP Routing
- Modem String Settings
- LAN DHCP Server
- Routing Settings
- Routing Table
- Filter Settings
- Wireless Settings
- Refresh Device List
- Device Name and Password
- Save Settings to File
- Load Settings
- Upgrade Firmware
- General Diagnostic
- Chapter 6 - RouteFinder Monitor
- RouteFinder Monitor
- Running RouteFinder Monitor
- Refresh Device List
- Test Connection
- Terminate Connection
- Save to File
- Save Now
- Autosave
- IP Address/Name
- Event Messages
- TCP/IP Tab
- Time Tab
- Status Tab
- Statistics Tab
- Chapter 7 - LAN Client Settings
- LAN Client Settings
- Setting up Remote Access Clients
- Accessing a Windows NT Server
- Accessing a Novell Server
- Accessing a Windows NT Server and a Novell NetWare Server
- Accessing a Unix Server
- Make New Connection (Windows 2000 only)
- Chapter 8 LAN-to-LAN Settings
- LAN-to-LAN Settings
- Setting up LAN-to-LAN Routing
- Using the Find Computer command
- Using LMHosts
- Chapter 9 - Troubleshooting
- Troubleshooting
- Common Problems
- Chapter 10 - Service, Warranty and Technical Support
- Introduction
- Limited Warranty
- Addendum for North American Products
- Addendum for International Products
- Out of Warranty Repair Costs
- Software User License Agreement
- Technical Support
- Contacting Technical Support
- Recording RouteFinder Information
- Online Warranty Registration
- About the Internet
- Ordering Accessories
- Appendixes
- Appendix A - Regulatory Compliance Information
- Class B Statement FCC Part 15
- Appendix B - Tools for your RF802EW
- RouteFinder Monitor
- PING
- WINIPCFG and IPCONFIG
- TRACERT
- Appendix C - Cabling Diagrams
- Glossary
- Index
113
Glossary
The following is a glossary of terms used in this manual:
B
Baudrate
Baudrate refers to the number of bits per second (Bps) that are transmitted between your
network device and modem or ISDN TA.
D
DHCP (Dynamic Host Configuration Protocol)
A protocol that was made to lessen the administrative burden of having to manually configure
TCP/IP Hosts on a network. DHCP makes it possible for every computer on a network to extract
its IP information from a DHCP server instead of having to be manually configured on each
network computer. The DHCP server built-in to your RouteFinder allows every computer on your
network to automatically extract IP information from the RouteFinder.
Why is it called Dynamic?
Each time a network client turns on their computer your RouteFinder DHCP server will
automatically give them an IP address from the IP address pool configured in the DHCP
Configuration dialog box in RouteFinder Manager. It is called Dynamic because the address that
is issued could be different each time a computer connects to the network.
DNS (DomainNameSystem)
A DNS Server can be thought of as the computer at your ISP whose job is to take all the URLs
that you type into your web browser and translate them to their corresponding IP address. To
use this the DNS translator, you need to know the IP address of your ISP’s DNS Server.
E
Ethernet
A LAN (Local Area Network) protocol developed by Xerox and DEC. It is a very commonly used
type of LAN.
F
Firewall
A system designed to prevent unauthorized access to or from a private network. Firewalls are
typically installed to give users access to the Internet while protecting their Internal Information.
Your RouteFinder uses a firewall technology known as NAT (see NAT). Each message entering
or leaving the intranet passes through the firewall. The firewall examines each message and
blocks those that do not meet the specified security criteria.
Firmware
Software that has been has been permanently or semi-permanently written to the RouteFinder’s
memory. Your RouteFinder supports flash ROM which means you can upgrade the fimware in
your network device very easily by downloading a copy of the new firmware from the Multi-Tech
web site and using the RouteFinder Manager Upgrade Firmware function.
FTP (File Transfer Protocol)
A protocol which allows a user on one host to access,and transfer files to and from another host
over a network.
I
IP (Internet Protocol)
The Internet Protocol is the network layer for the TCP/IP Protocol Suite. It is a connectionless,
best-effort packet switching protocol.
Intranet
An Intranet is the use of Internet technologies within a company. Intranets are private networks
that exist only within organizations, while the Internet is a global network open to all.