User's Manual
Table Of Contents
- _
- Contents
- Chapter 1 - Introduction
- _
- Front Panel
- Front Panel Description
- Back Panel
- Back Panel Description
- Typical Applications
- Connecting a Remote Site via Cable Modem
- Connecting a Local Site to the Internet
- Specifications
- Chapter 2 - Hardware Installation
- Hardware Installation
- Safety
- Unpacking the RF802EW
- Cabling
- Chapter 3 - Software Installation and Configuration
- Software Installation and Configuration
- Software Installation
- Using RouteFinder Setup Wizard
- Testing your Connection
- Chapter 4 - Telnet
- Using Telnet to Configure your RouteFinder
- Chapter 5 - RouteFinder Manager
- RouteFinder Manager
- General Settings
- WAN Ethernet Segment
- Async Port
- Remote Access-Remote Access Settings
- Enable IP Mapping - Virtual Server
- Port Settings
- Edit Login Script for Remote Access
- Writing a login script for IP Routing
- Modem String Settings
- LAN DHCP Server
- Routing Settings
- Routing Table
- Filter Settings
- Wireless Settings
- Refresh Device List
- Device Name and Password
- Save Settings to File
- Load Settings
- Upgrade Firmware
- General Diagnostic
- Chapter 6 - RouteFinder Monitor
- RouteFinder Monitor
- Running RouteFinder Monitor
- Refresh Device List
- Test Connection
- Terminate Connection
- Save to File
- Save Now
- Autosave
- IP Address/Name
- Event Messages
- TCP/IP Tab
- Time Tab
- Status Tab
- Statistics Tab
- Chapter 7 - LAN Client Settings
- LAN Client Settings
- Setting up Remote Access Clients
- Accessing a Windows NT Server
- Accessing a Novell Server
- Accessing a Windows NT Server and a Novell NetWare Server
- Accessing a Unix Server
- Make New Connection (Windows 2000 only)
- Chapter 8 LAN-to-LAN Settings
- LAN-to-LAN Settings
- Setting up LAN-to-LAN Routing
- Using the Find Computer command
- Using LMHosts
- Chapter 9 - Troubleshooting
- Troubleshooting
- Common Problems
- Chapter 10 - Service, Warranty and Technical Support
- Introduction
- Limited Warranty
- Addendum for North American Products
- Addendum for International Products
- Out of Warranty Repair Costs
- Software User License Agreement
- Technical Support
- Contacting Technical Support
- Recording RouteFinder Information
- Online Warranty Registration
- About the Internet
- Ordering Accessories
- Appendixes
- Appendix A - Regulatory Compliance Information
- Class B Statement FCC Part 15
- Appendix B - Tools for your RF802EW
- RouteFinder Monitor
- PING
- WINIPCFG and IPCONFIG
- TRACERT
- Appendix C - Cabling Diagrams
- Glossary
- Index
10
Chapter 1 - Introduction
Specifications
Hardware ARM RISC CPU
32 bit, 40MHZ
4MB DRAM and 512k Flash ROM
UART Serial port controller
LAN Port Interface: 1 10Base-T/100BaseTX RJ-45 Connection
Standard: 802.3
WAN Ports 1 x 10Base-T
1 x RS232 (V.24)
DTE Speed: Up to 230K asynchronous
Wireless
Access Point IEEE 802.11b for wireless LAN
Date Rates: 11, 5.5, 2, 1 Mbps data rate per channel
RF Frequency: 2.4-.24835 Ghz
Emission Type: Direct Sequence Spread Spectrum
Operating Range: Up to 100 meters indoors and 300 meters outdoors
Antenna: Dual Dipole with Diversity
Antenna Gain: 2 dB MAX
Protocols Security: PAP/CHAP, NAT Firewall, RADIUS, Callback, WEP
Network: TCP/IP, IPX, DHCP, PPP, PPPoE
Routing: Static, RIP 1, VPN, IPSec & PPTP Pass-Through
Filtering: Protocol, port number, and IP address
Power Output 5V DC, 2000mA
Dimensions 7.1” x 4.9” h x 1.4” d
(18.1 cm x 12.5 cm x 2.5 cm)
Weight 380g
13 oz.
Memory RAM: 4MB
Flash ROM: 512k
Operating
Environment: Temperature Range: 32-120 degrees F (0-50 degrees C)
Humidity: 25-85% non-condensing
Approvals: FCC Part 15 Class B & ETS 300 328
Warranty 2-year warranty