6x9 (D.I.Y.) with Optional Center Girts and Floor Kit Instructions Mueller D.I.Y. buildings are not engineered structures and do not meet any specific building code criteria. 877-2- MUELLER • www.muellerinc.
Mueller Mueller Inc Inc ‐ 6 x 9 DIY Back Yard Kit Instructions; Instructions; For For additional additional information, information, see see the the D.I.Y D.I.Y Installation Installation Video Video PG 2 Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video st PARTS LIST ng improvements, please refer to the parts list on the itemized invoice delivered with your building.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video TYPES OF SCREWS Lap TEK Screw For attaching sheet metal to sheet metal TEK Screw For attaching sheet metal to purlin ⅞" 1 ¼" 36" 10" Lap TEK Screw 12" TEK Screw 12" TEK Screw NOTE: Make sure to use TEK screws to attach sheets to purlins, lap TEK screws to attach sheets to sheets.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video BASE LAYOUT (BC-1 AND BP-1) STEP 1 Insert BP-1 into BC-1 STEP 2 Add MKB-1 (Galvanized MKB-2) to top of BP-1 into BC-1 NOTE: Leading and trailing edge of channels are overbent for a tight fit. Spread apart as needed to nest the purlin into the channel. BP-1 (Base Purlin) BC-1 (Base Channel) BP-1 (Base Purlin) Leveling and proper blocking is critical for the base layout.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video MAKE SURE THE ASSEMBLY IS SQUARE NOTE: Mueller recommends the building be placed on leveling blocks (not included) to support the base channel and purlins. Mueller also recommends the building be anchored to the ground or foundation. The method of anchor is at the owner’s discretion. Make sure the assembly is square. Assembly is square when the corner to corner measurements are equal.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video FLOOR KIT (OPTIONAL) NOTE: Mueller recommends the building be placed on leveling blocks (not included) to support the base channel and purlins. Mueller also recommends the building be anchored to the ground or foundation. The method of anchor is at the owner’s discretion.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video ERECTING COLUMNS (C-1) Attach column to MKB-1 (Galvanized MKB-2) clip using 1/2"x1" Fin Head Bolts HINT: Add clips to top of columns before standing up.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video RAFTERS (R-1) R-1 Bolts should remain loose until EC-1 is installed Place one bolt as shown.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video EAVE CHANNEL (EC-1) Tighten bolts after EC-1 is installed.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video MAKE SURE THE ASSEMBLY IS SQUARE AND LEVEL 11 R-1 EC-1 C-1 R-1 EC-1 C-1 BP-1 C-1 BC-1 C-1 BP-1 BC-1 Make sure the assembly is square. Assembly is square when the corner to corner measurements are equal. Use temporary bracing (not included) to hold assembly square if required.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video MID-GIRTS (OPTIONAL - MG-1, MG-2 AND MG-3) NOTE: Bolt to inside of column leg -1 MG MG MG -2 MKB-1 Clip -2 -1 MG -3 MG -3 MG MG -2 -3 MG TEK Screws To attach MG-3, use TEK screws to go through door trim, door frame and girt.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video Eave Trim WINDOW (OPTIONAL) Lap TEK Screw Start sheet 1” in from steel line. Sheet 1” above bottom of base channel Use inside/outside closures behind drip trim DripTrim NOTE: Sheets below window will need to be field cut for window assembly. Install one full sheet, then partial sheet. Insert window and flap flush to sheet. Add drip edge window trim when installing eave trim.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video SHEETING SCREW PLACEMENT WALL SHEETS 36" 10" Lap TEK Screw 12" TEK Screw TEK Screw ROOF SHEETS TEK Screw 36" 10" Lap TEK Screw 12" 12" TEK Screw Place sealer tape between roof sheets only. 12" TEK Screw TEK Screw NOTE: Make sure to use TEK screws to attach sheets to purlins, lap TEK screws to attach sheets to sheets.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video SHEETING SIDEWALL WITH SINGLE DOOR Outside closures Inside closures 1" Endwall IMPORTANT: 1" above the bottom of the base channel TOP VIEW Sidewall Inside closure goes on the bottom and outside closure goes on top.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video TOP VIEW Endwall SHEETING SIDEWALL WITHOUT DOOR Sidewall Inside closure goes on the bottom and outside closure goes on top.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video SHEETING SIDEWALL WITHOUT DOOR Sidewall TOP VIEW Endwall 1" Inside closure goes on the bottom and outside closure goes on top.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video SHEETING NOTE: Make sure the frame is plumb and level, and tighten all bolts prior to sheeting. Repeat for each wall. TOP VIEW Door Jamb Door J-Trim Panel TEK Screw NOTE: For side with door, start sheets flush with J-trim on both sides of the door.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video BACK SIDE WALL Roof to wall sheet alignment Align major ribs from wall to major rib on roof NOTE: Make sure panels remain square during installation.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video 23 36" 10" 12" 12" SHEETING THE ROOF Align roof sheets with wall sheets Place sealer tape between roof sheets only Lap TEK Screw TEK Screw TEK Screw TEK Screw Inside Closure Eave Trim NOTE: Use TEK screws at the purlins Use Lap TEK screws every 20" vertically TOP VIEW 4.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video ROOFING TRIM DETAILS CAUTION: Use scaffold boards (not included) for support while installing roof sheets and trim.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video 25 SKYLIGHT RIDGE ROLL INSTALLATION CAUTION: Use scaffold boards for support while installing roof sheets and trim HINT: S crew corner of ridge roll and middle first to maintain pitch. Install remainder of screws. Foam Block (under Ridge Roll) Install lap screws on ridge roll every 12 inches Outside Closure Foam Block closes the gap in between the closures.
Mueller, Inc. 6 x 9 DIY Back Yard Kit Instructions; For additional information, see the D.I.Y Installation Video TOTAL BUILDING MEASUREMENTS 7'7" 7'1" 6'5.5" 9'5.
