877-2-MUELLER www.MuellerInc.com 12'x15' & 12'x21' DIY KIT FOR SLAB COLDFORM ENDWALL ERECTION MANUAL Mueller BYK buildings do not meet any specific code or engineering criteria. These buildings are intended to be erected in geographical locations which do not require engineered loads for buildings under 400 sq. ft.
TRIM PAGE
6" 10" 12" 2" BUTYLTAPE LAP SCREW TEK SCREW UPN-PANEL BACK SIDE VIEW X Y X & Y Dimensions are located further in the instructions Foam Closure CORNER TRIM To avoid leaking place sealer tape between roof sheets only.
HE AD ER JT RI M COLUMN J-TRIM DOOR DOOR SHOULD BE LOWER THAN BOTTOM OF TRIM DETAIL K JT RI M J TRIM J TRIM DOOR JAMB DOOR J-TRIM NOTE FOR DOOR SIDE SHEETING ONLY: START SHEET FLUSH WITH J-TRIM ON BOTH SIDES OF DOOR
36" 10" To avoid leaking place sealer tape between roof sheets only.
A DETAIL A E EL SID ANN H C FB OT L FT OT RT OT C HA N Note: Place only one bolt where shown to connect the MKB1 clip. The other bolt will be used when installing the corner column. Note: Leading and trailing edges of channel and columns are over bent for a tight fit. Spread apart as needed to nest the columns into the channel.
MAKE SURE THE ASSEMBLY IS SQUARE. ASSEMBLY IS SQUARE WHEN THE CORNER TO CORNER MEASUREMENTS ARE EQUAL. USE TEMPORARY BRACING TO HOLD ASSEMBLY SQUARE IF REQUIRED, TEMPORARY BRACING IS NOT INCLUDED.
EL DE SI ANN CH COLUMN DETAIL C BB COLUMN COLUMN DETAIL B OT CH AN COLUMN COLUMN B EL DE SI ANN CH COLUMN JAMB JAMB COLUMN C FB OT LF T JAMB DETAIL D COLUMN D
Mid-Girts Sold at additional cost on selected kits DETAIL E E DETAIL F VIEW OF THE BACK OF COLUMN F E G F G DETAIL G
DETAIL H HE A DE R HE AD ER
COLUMN J 1 MG COLUMN 1 MG NOTE: ONLY PUT THE BOTTOM BOLT IN LOOSELY UNTIL THE TOP SIDE CHANNEL IS INSTALLED I MG 2 1 MG 1 MG COLUMN NOTE: THE GIRT GOES TO THE INSIDE OF THE CLIP AS SHOWN DETAIL I DETAIL J Mid-Girts Sold at additional cost on selected kits MG 2 J 1 MG 1 MG MG 3 1 MG MG 3
DETAIL K DETAIL L E EL SID ANN CH E EL SID ANN CH DETAIL M E EL SID ANN CH E EL SID ANN H C E EL SID ANN CH
DETAIL N DETAIL N FT CH OP AN COLUMN COLUMN N COLUMN E EL SID ANN CH DETAIL O E EL SID ANN CH CN RA T FT ER BT CE OP E BT CE OP E E EL SID ANN H C N N CN TR AF TE R E EL SID ANN CH O N FT CH OP AN O
DETAIL P P TO PC H LIN R U E EL SID ANN CH AN R PU IN RL U P LIN R U P P P TO PC HA N LIN E EL SID ANN CH
Corner Mid-Girts Sold at additional cost on selected kits Side Wall DG MI MI T IR 1 MI DG I RT T1 IR DG DG MI MI DG I RT 2 T IR 1 3 MI DG I RT DG MI T IR 1 3 Note: Attach MKB clips to the girts then attach then to the columns
36" 10" LAP SCREW 12" 12" 2" BUTYLTAPE TEK SCREW UPN-PANEL DETAIL R BACK SIDE VIEW R Foam Closure DETAIL Q 3 4" Q START SHEET 3/4" PAST THE END OF THE FRAME AND 1" FROM THE BOTTOM OF BASE
36" 10" LAP SCREW 12" 12" 2" BUTYLTAPE TEK SCREW UPN-PANEL CORNER TRIM DETAIL S CORNER TRIM CORNER TRIM CORNER TRIM S
36" 10" To avoid leaking place sealer tape between roof sheets only.
U IL TA E D U CUT IN MIDDLE
SKY LIGHT FOAM CLOSURE ROOF PANEL TEK SCREW DETAIL V V
FRAMED OPENING IS 5'-10"x6'-5" WHEN INSTALLED PROPERLY THE OPEN HEIGHT OF THE DOOR IS 6'-1" 8'-2" 6'-5" 8'-11" 5'-10" KIT COMES WITH A MUELLER 5'-9 21"x 6'-5" M250 ROLL UP DOOR
