Cl ■ • I ;a I •• I Congratulations and thank you for purchasing the MTX Audio X3-17-THUNDER6 audio system designed for the Can-Am™ Maverick X3. Our audio system will deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
IN THE BOX I AWMC3 Bluetooth Media Controller XJ-17-DK AWMC3 Dash Kit MUDLEDC RGB Remote Control MUD100.
VEHICLE LAYOUT WE'RE HERE TO HELP We're here to help with any installation or technical support. Visit mtx.com to chat, call 1-800-225-5689 to speak with an MTX Technical Support representative, or visit youtube.com/user/MTXAudioUSA to view product videos. DON'T FORGET TO REGISTER YOUR PRODUCT Don't forget to register your new MTX Audio product. Visit mtx.com/productregistration or scan the QR code to the right.
THANKS AGAIN! Once you're done putting your new MTX Audio X3-17-THUNDER6 audio system to the test, and making all your friends jealous, be sure to find us online and let us know what you think. Leave a product review on the website, and connect with us over social media . Let's Get Social mtx.com Hr.Jilt;] Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MD< is a trademark of MiTek Corporation. All other trademarks are property of their respective owners.
X3-17-DK CAN-AM MAVERICK X3 DASH KIT OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our Can-Am® Maverick X3 dash kit designed for use with the MTX Audio AWMC3 Bluetooth all-weather head unit. This easy to install dash kit is the perfect OEM fit solution for your Can-Am® Maverick X3. So, congratulations on your purchase, thanks for your support and most importantly, enjoy the ultimate audio experience with MTX! WE’RE HERE TO HELP We’re here to help with any installation or technical support. Visit mtx.
FIT GUIDE Turbo / Max Turbo...................................................................................................................................2018 - 2019 Turbo R / Max Turbo R............................................................................................................................2017 - 2019 X-DS Turbo..........................................................................................................................................................
INSTALLATION Step 1 - Remove the cover from top center of the dash. Step 2 - Locate the four (4) dimples formed into the tray area on the top center dash. Two are located toward the front and two are at the rear under the cover that was just removed. Using a 1⁄8" drill bit, drill through the dimples just enough to expose the existing boss located below. Caution: Drilling deeper can damage the bosses beneath and prevent proper installation of the dash kit. 4 MTX.
Step 3 - Using a 1" hole saw, drill a hole in the top of the dash to pass the wiring harness through. Our recommended location is indicated in the picture. Note: The 12-volt power port can be removed and used to pass the harness through the dash if you do not desire to drill a separate hole. This will require the removal of the center dash console panel to remove the power port. Step 4 - Prepare the AWMC3 radio unit by removing the two (2) threaded studs from the back of the radio.
Step 6 - Sliding the plate toward the rear of the kit, install the radio into the kit opening from the rear making sure the top of the radio is between the kit face and compression plate. Once in position, press the radio forward into the opening until it is flush with the front and aligned with the pre-molded screw holes. Step 7 - Using the two (2) longer screws, secure the bottom of the radio to the kit. 6 MTX.
Step 8 - While pressing the pressure plate forward against the radio chassis, tighten the two (2) screws left loose in Step 5. Step 9 - Prepare the pigtail harness supplied with the AWMC3 radio for installation by connecting additional wire to reach power / ground locations, speaker wire if needed and amplifier turn on wire. Note: If the radio installation is part of a full plug and play kit, use the pigtail supplied with the kit and not the radio.
Step 11 - With connections made, collect the wire harness under the kit shroud and place the radio kit on top of the dash aligning it with the four (4) holes drilled earlier. Making sure all wires are tucked under the kit, secure it in place with the four (4) screws provided Step 12 - With the radio secure, make the appropriate electrical connections to complete the install such as power, ground and remote turn on for amplifiers. Step 13 - Reassemble and go ride. 8 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
NOTES 10 MTX.
NOTES MTX.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006220 RevA 1/21 • 21A10809 • AW0015864 12 MTX.
X3-17-FS-U CAN-AM MAVERICK X3 FRONT UPPER SPEAKER PODS OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio 4" weatherproof upper dash speakers for your Can-Am® Maverick X3. With a few simple tools from your trusty toolbox you’ll have these installed in no time. The rotationally molded enclosures are built as a single piece, designed to take years of abuse without failure and they install quickly with only minor disassembly of the vehicle.
FEATURES • • • • • • • Custom Fit for Maverick X3 Dash Custom Quick Mount Bracket for Easy Installation Rotationally Molded Sealed Enclosure Factory Matched Texture Polypropylene Woofer and Mylar Dome Tweeter Installer Friendly Design Direct Fit, No Cutting Required • • • • • • RMS Power Handling: 50-Watts Peak Power Handling: 100-Watts Sensitivity (2.83V/1m): 89.9dB Sensitivity (1W/1m): 85.6dB Frequency Response: 75Hz - 20kHz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Turbo / Max Turbo..................
INSTALLATION Step 1 - On the driver side, locate and remove seven (7) T-30 Torx screws and two (2) pushpin rivets from the driver’s side upper dash panel. • Two (2) located to the left of the steering wheel. • Three (3) located at the front along the windshield line. 4 MTX.
• Two (2) located on either side of the steering wheel. • Two (2) pushpins located on the right side of the panel at top center tray. Step 2 - Disconnect the light switch harness from the back of the switch. Note: If any additional switches are mounted in this panel, disconnect at this time. If necessary, label harnesses to ensure proper reconnection. MTX.
Step 3 - Release and push the steering wheel to its lowest position for proper clearance. Step 4 - Lift up on the dash panel releasing the harness clips from the bottom side as you do. Step 5 - Once the panel is loose, disconnect the computer harness from the computer module attached to the panel and remove the panel from the vehicle. Note: It is not necessary to remove the computer module from the panel for installation of the speaker pod. 6 MTX.
Step 6 - On the passenger side, locate and remove five (5) T-30 Torx screws, one with 10mm nut, and two (2) pushpin rivets from the passenger’s side upper dash panel. • Two (2) located on the right side upper dash, one has a 10mm nut located behind gas cap cover panel. • Three (3) located at the front along the windshield line. MTX.
• Two (2) pushpins located on left side of the panel at top center tray. Step 7 - With hardware removed, lift up on the dash panel releasing the harness clips from the bottom side as you do. Step 8 - Once the panel is free, remove the panel from the vehicle. Step 9 - Prep the panels for installation by removing the speaker opening cover panel located on the bottom side of each panel. Note: Your vehicle may not have these installed if panels have been replaced or if audio equipment was previously installed.
Step 10 - Using side cutters or a razor knife, remove the four (4) mounting tabs on the bottom side of the panel around the speaker opening to provide proper clearance for the pod installation. Note: These DO NOT need to be perfectly flush with the back of the panel. Step 11 - Turn the panel over and locate the three (3) dimples around the molded speaker grill. Two (2) on top and one (1) on bottom of the grill area. Step 12 - Using a 3⁄16" drill bit, drill though the panel at each dimple location. MTX.
Step 13 - On the speaker pods, locate the single molded dimple at the bottom of the pod face. Step 14 - Using a 1⁄8" drill bit, pre-drill the hole approximately 1⁄8" deep to allow the mounting screw to be started by hand. Step 15 - Align the appropriate speaker pod on the back of the panel with the drilled holes and begin securing using two (2) machine screws through the front of the panel and into the threaded holes located on the pod bracket.
Step 17 - Tighten the machine screws securing the pod to the panel. Step 18 - Repeat this process on the other panel. Step 19 - With the panels back at the vehicle, route the pod speaker wire to its connection point. Note: If installing as part of a kit, the upper pod plug will connect to the pigtail located as part of the lower pod harness. If not installing as part of a kit, the plug will need to be removed and additional speaker wire added.
NOTES 12 MTX.
NOTES MTX.
NOTES 14 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006224 RevA 1/21 • 21A10811 • AW0015866 16 MTX.
X3-17-FS-L CAN-AM MAVERICK X3 FRONT LOWER SPEAKER PODS OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio 6.5" weatherproof kick panel speakers for your Can-Am® Maverick X3. With a few simple tools from your trusty toolbox you’ll have these installed in no time. The rotationally molded enclosures are built as a single piece, designed to take years of abuse without failure and they install quickly with only minor disassembly of the vehicle.
FEATURES • • • • • • • • Integrated RGB LED Lighting Custom Fit for Maverick X3 Kick Panel Custom Quick Mount Bracket for Easy Installation Rotationally Molded Sealed Enclosure Factory Matched Texture Polypropylene Woofer and Mylar Dome Tweeter Installer Friendly Design Direct Fit, No Cutting Required • • • • • • RMS Power Handling: 50-Watts Peak Power Handling: 100-Watts Sensitivity (2.83V/1m): 89.9dB Sensitivity (1W/1m): 85.
INSTALLATION Step 1 - Remove the outer front fender from both the driver and passenger side of the vehicle. Step 2 - On the driver side, locate and remove eleven (11) screws using a T30 Torx driver and 10mm wrench where needed. • Six (6) located in the wheel well area, one with a 10mm nut. • One (1) located at the top of the fender forward of the roll cage. Note: This is a longer bolt than the rest being removed. 4 MTX.
• One (1) located in the lower door jamb. • One (1) located in the front corner by the headlight with a 10mm nut. • Two (2) located inside vehicle, top of dash. MTX.
Step 3 - Remove two (2) metal clips and plastic retaining plates from the underside of the fender section attaching it to the driver’s side hood trim piece. Step 4 - Once the clips are removed, lift up on the hood trim and lift the outer fender piece up and back toward the rear of the vehicle to disengage it. Set it aside. 6 MTX.
Step 5 - The driver’s inner footwell panel will also be free now, remove it and set it aside for the installation process. Step 6 - On the passenger side, remove the gas cap cover panel and set aside. MTX.
Step 7 - Locate and remove twelve (12) screws using a T30 Torx driver and 10mm wrench where needed. • Six (6) located in the wheel well area, one with 10mm nut. • One (1) located at the top of the fender forward of the roll cage behind cover. Note: This is a longer bolt than the rest being removed. • One (1) located in the lower door jamb. 8 MTX.
• One (1) located in the front corner by the headlight with a 10mm nut. • One (1) located inside vehicle, top of dash with a 10mm nut on gas cap side. • One (1) located inside vehicle, top of dash. MTX.
• Two (2) from top dash panel. Step 8 - Remove two (2) metal clips and plastic retaining plates from the underside of the fender section attaching it to the passenger side hood trim piece. Step 9 - With these removed, lift the dash panel up from the vehicle exposing the gas filler neck below. 10 MTX.
Step 10 - Loosen the topmost hose clamp securing the fender assembly to the filler tube and slide the clamp down out of the way. Step 11 - Lift up on the hood trim piece and pull the fender up and away from the vehicle to remove it. Once removed, set aside. Note: Once removed, cover or stuff a clean rag into the filler tube to prevent gas fumes from escaping. Step 12 - Starting with the removed driver’s interior panel, locate and align the driver side template supplied with the speakers as shown.
Step 13 - Mark the five (5) holes with a marker or marking device. Step 14 - Using the supplied 1" hole saw, drill at each of the marked locations. Step 15 - Once the holes are drilled, temporarily reinstall the interior panel by reinserting the screw removed from the lower door jamb location. Step 16 - Repeat this process on the passenger side interior panel using the passenger side template. 12 MTX.
Step 17 - Starting on the driver’s side, begin by installing two hoop clamps over the vertical frame tube with the lower clamp facing the front of the vehicle and the upper facing the rear. Step 18 - Using two (2) longer 10mm bolts supplied, install the two saddle pieces into the hoop clamps leaving them loose enough to move up and down the frame tube. MTX.
Step 19 - Slide the correct mounting plate behind the frame tube aligning the clamps with the mounting slots on the plate. The holes of the plate should align with the holes you’ve already drilled in the inner fender panel. Plates are marked for driver and passenger’s side. Step 20 - Secure the mounting plate to the clamp assemblies using four (4) 10mm bolts and tighten the clamp bolts. 14 MTX.
Step 21 - Pass the driver side pod’s harness through the forward most hole. Step 22 - Holding the pod in place against the inside panel, align the threaded inserts with the holes in the mounting plate. Step 23 - Install four (4) 10mm bolts through the plate and secure the pod in place. MTX.
Step 24 - When complete, the plate assembly should appear as shown. Step 25 - Route the wire harnesses into the dash and make the appropriate speaker connections Note: If this install is part of a complete kit, the lower pod harness will connect to the main harness included in that kit. If installing outside a complete kit and hardwire connection need to be made, refer to the diagram for proper connectivity. Step 26 - For the passenger side pod, repeat the steps. 16 MTX.
Step 27 - Once the pods are installed and tested, the vehicle can be reassembled in the reverse order as disassembled. Note: The screw in the bottom of the driver’s door jamb that was temporarily reinstalled will need to be removed to reinstall the driver’s fender. Step 28 - Reassemble and go ride. MTX.
NOTES 18 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006222 RevA 1/21 • 21A10810 • AW0015865 20 MTX.
PASSENGER SIDE 0 ~1.00~ I L.____ ( 1.
DRIVER SIDE 0 0 0 0 0
X3-17-SW-D / XJ-17-SW-P CAN-AM® MAVERICK X3 SUBWOOFER ENCLOSURE OWNER'S MANUAL ADDENDUM NOTICE When installing your new X3 subwoofer enclosure, you may notice that the front mounting hole locations may not perfectly align with your seat bracket hole locations. During vehicle manufacturing, some variance can occur in the alignment of the seat brackets. This may requ ire the X3 seat bracket hole on the vehicle to be enlarged before installation to ensure proper fitment and mounting.
X3-17-SW-D CAN-AM MAVERICK X3 DRIVER SUBWOOFER ENCLOSURE OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit subwoofer enclosure designed for the Can-Am® Maverick X3. Our sub enclosure, with its 3512-04S 12" shallow subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • • • • • Includes an MTX 3512-04S 12" Shallow Subwoofer Mounts Under Driver Seat Factory Matched Texture Installer Friendly Design Direct Fit, No Cutting or Drilling Required • • • • • • • 12" Loaded Subwoofer Enclosure RMS Power Handling: 300-Watts Peak Power Handling: 600-Watts Sensitivity (2.83V/1m): 88.5dB Sensitivity (1W/1m): 84.4dB Frequency Response: 23Hz - 130Hz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Turbo / Max Turbo..................................................................
INSTALLATION Step 1 - Release the lower seat belt strap from the harness by feeding it back through the tension assembly. This will allow you to feed the shoulder straps through the hole at the top of the seat. Step 2 - Remove two (2) 13mm bolts and nuts at the front of the seat frame. 4 MTX.
Step 3 - Access the rear 18mm nuts using a socket with extension either by aligning the holes in the seat base over the nuts or by sliding the seat fully forward and reaching behind. Step 4 - With the seat free, disconnect the seat belt sensor and speed sensor cables from the seat assembly. Step 5 - Once disconnected, lift the seat out of the vehicle and set aside. Step 6 - Remove the 10mm M6 bolt holding the brake line clamp in place on the seat frame. MTX.
Step 7 - Remove the cable clamp from the brake line. Step 8 - Wrap the brake line with the strip of adhesive backed foam tape included in the box. Note: This step is to prevent the brake line from rattling against the enclosure under high bass output and any chaffing due to movement of the brake line while the vehicle is in motion. 6 MTX.
Step 9 - Tilt the front of the enclosure down and slide it under the forward crossbar as you set it in place onto the floor of the vehicle tucking the brake line into the pre-molded slot in the bottom of the enclosure. Step 10 - Taking the long bar bracket included, align the slotted holes with the threaded insets on the top rear of the enclosure. The two large holes at either end should slide over the threaded seat mounting posts. Step 11 - Loosely install three (3) T-40 Torx screws into the bracket.
Step 12 - Align the threaded inserts at the front corners of the enclosure with the holes in the bottom of the seat brackets and insert two (2) T-40 Torx screws. Step 13 - Once all fasteners are in place, tighten to secure the enclosure. 8 MTX.
Step 14 - Route the subwoofer cable to the desired connection point. Note: If installing as part of a kit, the subwoofer plug will connect to the main harness supplied. If not installing as part of a kit, the plug will need to be removed and additional speaker wire added. Step 15 - With your wire routed and system tested, reinstall the seat in the reverse order as removed.
NOTES 10 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006226 RevA 1/21 • 21A10812 • AW0015867 12 MTX.
X3-17-SW-D / XJ-17-SW-P CAN-AM® MAVERICK X3 SUBWOOFER ENCLOSURE OWNER'S MANUAL ADDENDUM NOTICE When installing your new X3 subwoofer enclosure, you may notice that the front mounting hole locations may not perfectly align with your seat bracket hole locations. During vehicle manufacturing, some variance can occur in the alignment of the seat brackets. This may requ ire the X3 seat bracket hole on the vehicle to be enlarged before installation to ensure proper fitment and mounting.
X3-17-SW-P CAN-AM MAVERICK X3 PASSENGER SUBWOOFER ENCLOSURE OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit subwoofer enclosure designed for the Can-Am® Maverick X3. Our sub enclosure, with its 3512-04S 12" shallow subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • • • • • Includes an MTX 3512-04S 12" Shallow Subwoofer Mounts Under Passenger Seat Factory Matched Texture Installer Friendly Design Direct Fit, No Cutting or Drilling Required • • • • • • • 12" Loaded Subwoofer Enclosure RMS Power Handling: 300-Watts Peak Power Handling: 600-Watts Sensitivity (2.83V/1m): 88.5dB Sensitivity (1W/1m): 84.4dB Frequency Response: 23Hz - 130Hz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Turbo / Max Turbo...............................................................
INSTALLATION Step 1 - Release the lower seat belt strap from the harness by feeding it back through the tension assembly. This will allow you to feed the shoulder straps through the holes at the top of the seat. Step 2 - Remove two (2) 13mm bolts and nuts at the front of the seat frame. 4 MTX.
Step 3 - Access the rear 18mm nuts using a socket with extension either by aligning the holes in the seat base over the nuts or by sliding the seat fully forward and reaching behind. Step 4 - With the seat free, lift the seat out of the vehicle and set aside. Step 5 - Remove the 10mm M6 bolt holding the brake line clamp in place on the seat frame. MTX.
Step 6 - Remove the cable clamp from the brake line. Step 7 - Wrap the brake line with the strip of adhesive backed foam tape included in the box. Note: This step is to prevent the brake line from rattling against the enclosure under high bass output and any chaffing due to movement of the brake line while the vehicle is in motion. 6 MTX.
Step 8 - Tilt the front of the enclosure down and slide it under the forward crossbar as you set it in place onto the floor of the vehicle tucking the brake line into the pre-molded slot in the bottom of the enclosure. Step 9 - Taking the long bar bracket included, align the slotted holes with the threaded insets on the top rear of the enclosure. The two large holes at either end should slide over the threaded seat mounting posts. Step 10 - Loosely install three (3) T-40 Torx screws into the bracket.
Step 11 - Align the threaded inserts at the front corners of the enclosure with the holes in the bottom of the seat brackets and insert two (2) T-40 Torx screws. Step 12 - Once all fasteners are in place, tighten to secure the enclosure. 8 MTX.
Step 13 - Route the subwoofer cable to the desired connection point. Note: If installing as part of a kit, the subwoofer plug will connect to the main harness supplied. If not installing as part of a kit, the plug will need to be removed and additional speaker wire added. Step 14 - With your wire routed and system tested, reinstall the seat in the reverse order as removed.
NOTES 10 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006228 RevA 1/21 • 21A10813 • AW0015868 12 MTX.
