X3-17-SW-D / XJ-17-SW-P CAN-AM® MAVERICK X3 SUBWOOFER ENCLOSURE OWNER'S MANUAL ADDENDUM NOTICE When installing your new X3 subwoofer enclosure, you may notice that the front mounting hole locations may not perfectly align with your seat bracket hole locations. During vehicle manufacturing, some variance can occur in the alignment of the seat brackets. This may requ ire the X3 seat bracket hole on the vehicle to be enlarged before installation to ensure proper fitment and mounting.
X3-17-SW-D CAN-AM MAVERICK X3 DRIVER SUBWOOFER ENCLOSURE OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit subwoofer enclosure designed for the Can-Am® Maverick X3. Our sub enclosure, with its 3512-04S 12" shallow subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • • • • • Includes an MTX 3512-04S 12" Shallow Subwoofer Mounts Under Driver Seat Factory Matched Texture Installer Friendly Design Direct Fit, No Cutting or Drilling Required • • • • • • • 12" Loaded Subwoofer Enclosure RMS Power Handling: 300-Watts Peak Power Handling: 600-Watts Sensitivity (2.83V/1m): 88.5dB Sensitivity (1W/1m): 84.4dB Frequency Response: 23Hz - 130Hz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Turbo / Max Turbo..................................................................
INSTALLATION Step 1 - Release the lower seat belt strap from the harness by feeding it back through the tension assembly. This will allow you to feed the shoulder straps through the hole at the top of the seat. Step 2 - Remove two (2) 13mm bolts and nuts at the front of the seat frame. 4 MTX.
Step 3 - Access the rear 18mm nuts using a socket with extension either by aligning the holes in the seat base over the nuts or by sliding the seat fully forward and reaching behind. Step 4 - With the seat free, disconnect the seat belt sensor and speed sensor cables from the seat assembly. Step 5 - Once disconnected, lift the seat out of the vehicle and set aside. Step 6 - Remove the 10mm M6 bolt holding the brake line clamp in place on the seat frame. MTX.
Step 7 - Remove the cable clamp from the brake line. Step 8 - Wrap the brake line with the strip of adhesive backed foam tape included in the box. Note: This step is to prevent the brake line from rattling against the enclosure under high bass output and any chaffing due to movement of the brake line while the vehicle is in motion. 6 MTX.
Step 9 - Tilt the front of the enclosure down and slide it under the forward crossbar as you set it in place onto the floor of the vehicle tucking the brake line into the pre-molded slot in the bottom of the enclosure. Step 10 - Taking the long bar bracket included, align the slotted holes with the threaded insets on the top rear of the enclosure. The two large holes at either end should slide over the threaded seat mounting posts. Step 11 - Loosely install three (3) T-40 Torx screws into the bracket.
Step 12 - Align the threaded inserts at the front corners of the enclosure with the holes in the bottom of the seat brackets and insert two (2) T-40 Torx screws. Step 13 - Once all fasteners are in place, tighten to secure the enclosure. 8 MTX.
Step 14 - Route the subwoofer cable to the desired connection point. Note: If installing as part of a kit, the subwoofer plug will connect to the main harness supplied. If not installing as part of a kit, the plug will need to be removed and additional speaker wire added. Step 15 - With your wire routed and system tested, reinstall the seat in the reverse order as removed.
NOTES 10 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006226 RevA 1/21 • 21A10812 • AW0015867 12 MTX.
