X3-17-FS-U CAN-AM MAVERICK X3 FRONT UPPER SPEAKER PODS OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio 4" weatherproof upper dash speakers for your Can-Am® Maverick X3. With a few simple tools from your trusty toolbox you’ll have these installed in no time. The rotationally molded enclosures are built as a single piece, designed to take years of abuse without failure and they install quickly with only minor disassembly of the vehicle.
FEATURES • • • • • • • Custom Fit for Maverick X3 Dash Custom Quick Mount Bracket for Easy Installation Rotationally Molded Sealed Enclosure Factory Matched Texture Polypropylene Woofer and Mylar Dome Tweeter Installer Friendly Design Direct Fit, No Cutting Required • • • • • • RMS Power Handling: 50-Watts Peak Power Handling: 100-Watts Sensitivity (2.83V/1m): 89.9dB Sensitivity (1W/1m): 85.6dB Frequency Response: 75Hz - 20kHz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Turbo / Max Turbo..................
INSTALLATION Step 1 - On the driver side, locate and remove seven (7) T-30 Torx screws and two (2) pushpin rivets from the driver’s side upper dash panel. • Two (2) located to the left of the steering wheel. • Three (3) located at the front along the windshield line. 4 MTX.
• Two (2) located on either side of the steering wheel. • Two (2) pushpins located on the right side of the panel at top center tray. Step 2 - Disconnect the light switch harness from the back of the switch. Note: If any additional switches are mounted in this panel, disconnect at this time. If necessary, label harnesses to ensure proper reconnection. MTX.
Step 3 - Release and push the steering wheel to its lowest position for proper clearance. Step 4 - Lift up on the dash panel releasing the harness clips from the bottom side as you do. Step 5 - Once the panel is loose, disconnect the computer harness from the computer module attached to the panel and remove the panel from the vehicle. Note: It is not necessary to remove the computer module from the panel for installation of the speaker pod. 6 MTX.
Step 6 - On the passenger side, locate and remove five (5) T-30 Torx screws, one with 10mm nut, and two (2) pushpin rivets from the passenger’s side upper dash panel. • Two (2) located on the right side upper dash, one has a 10mm nut located behind gas cap cover panel. • Three (3) located at the front along the windshield line. MTX.
• Two (2) pushpins located on left side of the panel at top center tray. Step 7 - With hardware removed, lift up on the dash panel releasing the harness clips from the bottom side as you do. Step 8 - Once the panel is free, remove the panel from the vehicle. Step 9 - Prep the panels for installation by removing the speaker opening cover panel located on the bottom side of each panel. Note: Your vehicle may not have these installed if panels have been replaced or if audio equipment was previously installed.
Step 10 - Using side cutters or a razor knife, remove the four (4) mounting tabs on the bottom side of the panel around the speaker opening to provide proper clearance for the pod installation. Note: These DO NOT need to be perfectly flush with the back of the panel. Step 11 - Turn the panel over and locate the three (3) dimples around the molded speaker grill. Two (2) on top and one (1) on bottom of the grill area. Step 12 - Using a 3⁄16" drill bit, drill though the panel at each dimple location. MTX.
Step 13 - On the speaker pods, locate the single molded dimple at the bottom of the pod face. Step 14 - Using a 1⁄8" drill bit, pre-drill the hole approximately 1⁄8" deep to allow the mounting screw to be started by hand. Step 15 - Align the appropriate speaker pod on the back of the panel with the drilled holes and begin securing using two (2) machine screws through the front of the panel and into the threaded holes located on the pod bracket.
Step 17 - Tighten the machine screws securing the pod to the panel. Step 18 - Repeat this process on the other panel. Step 19 - With the panels back at the vehicle, route the pod speaker wire to its connection point. Note: If installing as part of a kit, the upper pod plug will connect to the pigtail located as part of the lower pod harness. If not installing as part of a kit, the plug will need to be removed and additional speaker wire added.
NOTES 12 MTX.
NOTES MTX.
NOTES 14 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006224 RevA 1/21 • 21A10811 • AW0015866 16 MTX.
