MTX series MTX0808DA MTX1608DA MTX1616DA DVI and Stereo-Audio Matrix Switcher User Manual (English) COMM-TEC GmbH Siemensstr. 14 D-73066 Uhingen Tel.: +49-7161-3000-0 Fax: +49-7161-3000-333 www.comm-tec.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series Table of Contents 1. Safety Warnings / Precautions...................................................................................................................................2 2. About the Product ......................................................................................................................................................3 3. Installation ..............................................................................
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series FCC / CE Notice • • This device complies with part 15 or the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 2.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 2.4 Back Panel Back panel 8 x 8 with Audio Depending on the model of the matrix, the video signal I/O interface is made up of 8 or 16 DVI-D female terminals. Audio signal I/O terminals are made up of 8 or 16 5pin captive screw terminals for each channel (left & right together). The channel numbers of the signal I/O terminals start from channel 1 to the maximum number of channels depending on the model.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 3.4 RS-232 Connection All functions of the MTX units can be controlled with external controllers like computers or third party controllers (e.g. AMX). A serial controller is any device that is connected to the standard RS-232 serial port (9pin SubD female) on the rear panel and that can send and receive ASCII character format.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series Input Comm and： 0 / ENTER END 1B3， 4. 7. Press the button “ENTER” to perform this command. Display feedback on LCD: “Switch OK” 1B3,4. RECALL 6. Press the button “END” to finish the command. Display feedback on LCD: “.” Switch OK Switch OK! AV: 01 -> 004 Example 2: To inquire the status on the output channel No.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 4.3 RS-232 Operation Through the RS-232 port located on rear panel one is able to control and operate the MTX Matrix remotely. Communication protocol: RS-232, ASCII commands are case sensitive. Port Settings: Baud rate: 9600, Data bit: 8, Stop bit: 1, Parity bit: None ASCII Commands and Protocols Example Default Rewrites the password. Must be 8 digits.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 5. Specifications Type Spezifikationen Video Bandwidth MTX0808DA MTX1608DA, MTX1616DA 165MHz (-3dB), all digital Resolution 1600x1200 @60 bit Clock Jitter: <0.15Tbit Switching speed Video input 200ns Connector DVI-D female Signal strength T.M.D.S +/- 0.4Vpp Maximum/Minimum level T.M.D.S 2.9V/3.3V Resistance 50 Ω Max. distance < than 36m, 1600x1200@60Hz Video Output Connector Maximum/Minimum level DVI-D female T.M.D.S 2.9V/3.
User Manual for DVI/Stereo-Audio Matrix COMM-TEC MTX Series 6. Warranty, Service and Returns Policy This product is under warranty for a period of one (1) year from the date of purchase. COMM-TEC’s liability and Buyer’s remedies under this warranty shall be limited solely to repair of the faulty units free of charge. This warranty does not apply if the product has been modified, repaired by an unauthorized agent, or improperly installed, used, or maintained.
