7HUIWIEB ..SPORTS. OWNER'S MANUAL MUDRZRDK POLARIS® RZR® DASH KIT [FOR USE WITH MTX WET-MC3 HEAD UNIT] MTX.
IMPORTANT NOTICE If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support at 1-800-225-5689. When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle's battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.
SPECI FICAT IONS __@ __ MTX COM 3
INSTALLATI ON Step 1 - Release the two quick locks to remove the hood from the veh icle. Step 2- Lift up the hood and slide towards the front of the vehicle. Step 3- Remove the two (2) T40 screws holding down the top dash cover. MTX .
Step 4- Lift and pull back the top dash cover to release the clips holding it in place. Unplug the gauge and switches making sure not to damage the vehicle and ignition wiring. Make note to remember what connector is associated with each specific switch. Step 5- Remove the Torx head screw from the dash pocket brace. After this is removed the plastic dash pocket can be pulled out of the dash. MTX .
Step 6- Remove the center pocket after it has been disconnected from the brace. Step 7- Turn the center pocket upside down to access the protective cover pins. Pry the two pins loose using a pry tool to remove the cover. Step 8- Slide the two included speed clips onto the rear of the dash piece. MTX.
Make sure the speed clips are orientated according to the picture below. Step 9- Th1s dash kit also offers additional space to mount up to two rocker panel switches for accessories. On the rear of the dash kit, grooves are provided to give you proper location and size for mounting additional switches. Step 10- Before mounting the source unit to the dash kit, make sure that the trim bezel that is included with the source unit is NOT attached. If it is attached, it will need to be removed.
Step 11 -Attach the source unit to the rear of the dash kit using the included nuts. Step 12- One of the circular knockout panels on the rear of the pocket will need to be removed to provide an access hole to route wiring from the source unit to the vehicle. Step 13 -Attach the dash kit to the center pocket by first inserting the wiring into the pocket. Connect the wiring to the source unit and feed the wiring out of the rear of the pocket hole that was cut.
Step 14- Insert the tab on top of the dash kit into the slot on the pocket. Step 15- Once the dash kit is locked in, use the two included shoulder bolts to attach the bottom of the dash kit to the pocket. NOTE: Make sure the speed clips used in Step 8 are lined up correctly or the bolts will not be able to be tightened. Step 16- Slide the dash kit, source unit and wiring back into the dash. MTX .
Step 17- Reattach the rear support bracket to the pocket. Once rear brace is secure, the dash kit is installed and the vehicle can be put back together. 10 MTX .
• , • , © 2016 Mitek Corporation. All rights reserved. MTX, Mud Nation, and Let's Do Something Dirty are trademarks of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX005499 RevA 6/16 • 21 A10514 • AW0015315 MTX .
11 OOPM BLUETOOTH Song Title Artist Album 23/25 _.... 3:08 n .M!5C <.... I .._.
IMPDIITANT NOTICE If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support atl-800-225-5689. When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle's battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.
WillE CONNECTION A w Power I Speaker Connector Black AUXIn Grey_, · Line Out (Front) Brown Line Out (Rear) Antenna DIN USB POIIIIEII AND SPEAKER CONNECTION Pin # Wire Color Wire Definition 11 12 White I Black White Green I Black Green Front left Speaker(-) Front left Speaker(+) Rear left Speaker(-) Rear left Speaker(+) 8 Grey Grey I Black Purple Purple I Black Front Right Speaker(+) Front Right Speaker(-) Rear Right Speaker(+) Rear Right Speaker(-) 2 Blue Remote Output 10 Yellow Bat
INSTALLATIO N Mounting (Using Mounting Plate) To mount the unit, find a flat surtace with adequate clearance behind it that provides enough room for the unit and all it's necessary wiring. • Once a mounting location has been determined, cut a circular hole 3" (77mm) in diameter. • After the hole is cut, slide the unit and wiring through the hole. A piece of self adhesive EVA foam is supplied in order to create a water resistant seal. This may be placed on the back side of the unit if desired.
INSJ'AI.I.AJ'ION Mounting (Using Optional Vehicle Specific Dash Mount Kit - Sold Separately) The unit will be mounted to each vehicle differently. Make sure to following the vehicle specific directions that were included with the dash kit. • Slide the two included speed clips onto the rear of the dash kit. • The dash kit may include additional space to mount rocker panel switches for accessories.
CONTROLS 0 ® Song Title Artist Album 23/25 3:08 1. Power Button ( (!.>) -This push button (On I Off) supplies power to the head unit. 2. Volume I Function Control Knob - Rotate knob to set values and control volume. Press and hold knob for 3 seconds to access EQ menu and confirm function values. 3. Source Button -This push button switches between audio sources. Use the Function Control Knob (2) to change and confirm selections. 4. Mute Button -This push button mutes the audio. 5.
GENERAL OPERATIONS Switching On and Off Press Power Button(~) to turn the device On. Hold Power Button(~) to turn the device Off. Operating Mode Press Source Button to switch between radio reception (AM I FM I WB I SXM), audio input (AUX), USB and Bluetooth audio streaming (BT MUSIC). Rotate the VOL knob to change selections and press VOL knob to enter operating mode. Volume Rotate VOL knob to set the volume. Sound Settings Hold VOL knob for 3 seconds to enter EO.
RADIO FUNCTIONS Selecting Radio Band • Press Source Button and rotate VOL knob. • Press VOL knob to select radio band. • Select FM or AM band. Automatic or Manual Search Frequencies • Press and hold the Previous I Next Buttons ( <~ I •> )to start automatic station search. The search stops when a station is found . • Press the Previous I Next Buttons ( <~ I •> ) briefly to change the frequency until the desired frequency is set.
RADIO FUNCTIONS Local • Press Menu Button to enter FM Settings. • Press VOL knob and rotate to select Local. • Press VOL knob and rotate to select Local ON I OFF. Note: Only stations with good reception quality will be played under the Local setting. Select USA I Europe Area Frequencies • Press Menu Button to enter FM Settings. • Press VOL knob and rotate to select Radio Region. • Press VOL knob and rotate to select USA I Europe Frequencies.
SiriusXW OPERATION Selecting SiriusXM • Press the Source Button and rotate VOL knob. • Press VOL knob to select SXM mode. Note: If there is no SiriusXM Tuner connected this mode will be skipped. Please connect your SiriusXM Tuner to the SiriusXM port located at the back of the unit. Manual Channel Selection Press the Previous I Next Buttons ( ~I is set.
SiriusXW DPEIIIITIDN Parental Control SiriusXM channels can be locked, and will need a pass code to access. The default code is "5220". If the pass code is forgotten, simply run the SXM Factory Default to reset the pass code. GUIDE ON HOW TO ENTER THE CODE USING THE VOLUME BUTTON: When the first character is flashing, turn the rotary knob to select number 5 and press to enter. When the second character flashes, use the same operation to select the rest of the characters "2","2","0".
SiriusX_. OPERATION Troubleshooting (cont) Subscription Updated The radio has detected a change in your SiriusXM subscription status. Press any button to clear the message. In the U.S.A., visit www.siriusxm.com or calll-866-635-2349 if you have questions about your subscription. In Canada, visit www.siriusxm.ca or call 1-877-438-9677 if you have questions about your subscription.
BLUETOOJ'H AUDIO SJ'REAMING This unit supports Bluetooth for wireless music streaming from Bluetooth enabled devices including iPhone®and Android®smartphones and tablets. 1. Turn on the Bluetooth feature of the mobile device. Scan for available Bluetooth devices within range. Select "MTX-MC3" . (Please refer to the mobile device's instruction manual for Bluetooth Pairing). 2. After successfully pairing, connect the mobile device to the AWMC3 via Bluetooth.
SPECIFICATIONS TunerFM Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio Tuner AM Frequency Range 87.5- 107.9 MHz (America) 87.5- 108 MHz (Europe) 200kHz (America) 50 kHz (Europe) 2.8 ~v 30d8 50d8 Usable Sensitivity 530- 1710KHz (America) 522- 1620KHz (Europe) 32d8 TunerWB Frequency Range 162.4- 162.55 MHz Line-Out Output Impedance 2V 10k Ohm General Power Supply Speaker Impedance Output Power Fuse 12V DC (10.8-15.6V allowable) 2-8 ohm 50Wx4CH .
This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
7HUMIEII .SPORTS. OWNER'S MANUAL RZRPOD65 POLARIS® RZR® DASH SPEAKERS MTX.
IAfPORrANT NOTICE If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support at 1-800-225-5689. When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle's battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.
INSTALLATION Step 1 - Release the two quick locks to remove the hood from the vehicle. Step 2 - Lift up the hood and slide towards the front of the vehicle. Step 3 - Remove the two (2) T40 screws holding down the top dash cover. MTX.
Step 4- Lift and pull back the top dash cover to release the clips holding it in place. Unplug the gauge and switches making sure not to damage the vehicle and ignition wiring. Make note to remember what connector is associated with each specific switch. Step 5- Wipe the bottom surface of enclosure with isopropyl alcohol. Adhere the double sided 3M tape strips to the bottom of enclosure per locations shown in the picture. Do not remove the backing yet. 4 MTX .
Step 6- Place the left and right pods in their perspective locations. Wiring will be orientated toward the center of the machine. The left pod is slightly larger than the right pod. Run the wire through the small opening between the body panel and the roll cage . Make sure to not pinch or damage the wire. The wire can be reached from the inside of the body panel through the dash cover opening.
Step 8- Remove the 15mm bolts from the roll cage on both right and left front roll cage junctions. Take the RZRPOD65 and the bracket and align the bracket mounting holes to the roll cage junction. The 15mm bolts that were removed will hold the bracket tight to the roll cage. The enclosures will sit within the front corners of the dash. Step 9- Securely attach the brackets to the enclosure using the provided M4 Screws.
Step 10- Replace all the parts and screws that have been removed and return the vehicle to its original assembled condition . MTX .
© 2016 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX005481 RevB 6/16 • 21 A10519 • AW0015329 8 MTX.
MUD65P CAGE MOUNT SPEAKER OWNER’S MANUAL MTX.
PRODUCT INFORMATION Model # Serial # Dealer’s Name Date of Purchase IN THE BOX • Speaker and Enclosure • Brackets • For mounting the bracket base to the enclosure • (8) M6-1.0x14mm stainless steel Hex Bolt • Ï- ÏmATÏWASHERÏSTAINLESSÏSTEEL • Ï- ÏSPLITÏLOCKÏWASHERÏSTAINLESSÏSTEEL • For tightening the bracket strap to the base • (2) M6-1.0x50mm stainless steel Hex Bolt • Ï- ÏSERRATEDÏmANGEÏLOCKÏNUTÏSTAINLESSÏSTEEL INTRODUCTION Thank you for purchasing this MTX Audio cage mount speaker pod.
INSTALLATION Ï #HOOSEÏAPPROPRIATEÏBRACKETÏCLAMP Ï 1b2", 13b4" or 2", for the application. Ï ! Ï TTACHÏBRACKETÏBASEÏTOÏENCLOSUREÏATÏDESIREDÏANGLEÏUSINGÏAÏMINIMUMÏOFÏTWOÏ ÏM6-1.0x14mm Hex BOLTSÏANDÏ- ÏLOCKÏWASHERS Ï)FÏONLYÏTWOÏ ÏBOLTSÏAREÏUSED ÏENSUREÏTHEREÏISÏAÏBOLTÏONÏEACHÏSIDEÏOFÏ the round base for secure mounting. Ï 3LIDEÏBRACKETÏCLAMPÏOVERÏPIPEÏORÏBARÏATÏDESIREDÏMOUNTINGÏLOCATION Ï ( Ï OLDÏTHEÏENCLOSUREÏINÏPLACEÏWHEREÏTHEÏBASEÏlTSÏINÏTHEÏOPENÏSECTIONÏOFÏTHEÏCLAMP Ï4HENÏPLACEÏTHEÏ M6-1.
The bracket base can rotate in any direction desired, a minimum of 2 bolts must be used, 1 on each side. © 2015 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and Engineered in the U.S.A. $UEÏTOÏCONTINUALÏPRODUCTÏDEVELOPMENT ÏALLÏSPECIlCATIONSÏAREÏSUBJECTÏTOÏCHANGEÏWITHOUTÏNOTICE Ï MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX005257 RevA 7/15 •21A10428 • AW0015151 4 MTX.
MUD100.2 10 0 WAT TS x 2 RMS 2 CHANNEL AMPLIFIER OWNER’S MANUAL MUD100.2 AMPLIFIER Use your smartphone to scan or visit youtube.com/user/MTXAudioUSA to learn how to properly install this amplifier. MTX.
PRODUCT INFORMATION Model # Serial # Dealer’s Name Date of Purchase INTRODUCTION Thank you for purchasing this MTX Audio Hi-Performance amplifier. Proper installation matched with MTX speakers and subwoofers provide superior sound and performance for endless hours of enjoyment whether you are waking the neighbors or just out enjoying your tunes.
PANEL LAYOUT 1 WHITE: L+ BRIDGE+ WHT/ BLK: L– GREY: R+ GREY/ BLK: R– BRIDGE– RED: 12V+ BLUE: REMOTE BL ACK: GND 2 3 LE VEL X-OVER FULL HI LOW MIN MA X MTX.
WIRING DIAGRAM See page 22 for amplifier wiring diagrams. INSTALLATION AND MOUNTING MTX recommends your new Thunder Sports™ amplifier be installed by a 12 volt installation specialist. Any deviation from specified installation instructions can cause serious damage to the amplifier, speakers and/or vehicle’s electrical system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior to system turn on. 1. Disconnect the vehicle’s negative battery cable. 2.
INSTALLATION For proper perfomance and safety, MTX recommends installing an inline fuse per the owner’s manual instructions according to the following. MUD100.
SPECIFICATIONS Model MUD100.2 Description 50 W RMS/CH Stereo RMS Power at 14.4V 41 Bridged Load 200 W RMS 21 Load 100 W RMS 41 Load 50 W RMS Features Input Level 0.2 - 5V Frequency Response 20Hz - 20 kHz Low Pass Filter (LPF) 80Hz Fixed High Pass Filter (HPF) 80Hz Fixed THD at 41 , 1W <0.2% Signal-to-Noise Ratio >85dB Minimum Load 21 Low Voltage Protection Yes, Protect <8V Components & PCB SMD Parts / Double Sided FR-4 PCB Dimensions 6 Height 1.61" (40.9mm) Width 5.71" (145.
INFORMACIÓN DEL PRODUCTO Número de modelo Número de serie Nombre del distribuidor Fecha de compra INTRODUCCIÓN Gracias por comprar un amplificador de audio de alto rendimiento MTX. La instalación correcta, combinada con altavoces y subwoofers MTX, produce un sonido y un rendimiento de calidad superior durante incontables horas de placer, sea que esté despertando a los vecinos o simplemente disfrutando de su música. Felicitaciones, y disfrute de lo máximo en experiencias de audio con MTX.
DISPOSICIÓN DEL PANEL 1 WHITE: L+ BRIDGE+ WHT/ BLK: L– GREY: R+ GREY/ BLK: R– BRIDGE– RED: 12V+ BLUE: REMOTE BL ACK: GND 2 3 LE VEL X-OVER FULL HI LOW MIN 8 MA X MTX.
DIAGRAMA DE CABLEADO Consulte la página 22 para los diagramas de cableado del amplificador. INSTALACIÓN Y MONTAJE MTX recomienda que su nuevo amplificador de Thunder Sports™ sea instalado por un distribuidor autorizado de MTX. Toda desviación de las instrucciones de instalación especificadas puede causar graves daños al amplificador, a los altavoces y/o al sistema eléctrico del vehículo. El daño causado por una instalación incorrecta NO está cubierto por la garantía.
INSTALACIÓN Para un correcto funcionamiento y seguridad MTX recomienda instalar un fusible en línea según las instrucciones del Manual del Propietario de acuerdo a lo siguiente. MUD100.
ESPECIFICACIONES Modelo MUD100.2 Descripción 50 W RMS/CH Stereo Potencia RMS a 14.4 V 41 con puente de carga 200 W RMS 2 1 de carga 100 W RMS 4 1 de carga 50 W RMS Características Nivel de entrada 0.2 a 5 V Respuesta de frecuencias 20 Hz a 20 kHz Filtro de pasabajas (LPF) 80Hz fijo Filtro de pasaaltas (HPF) 80Hz fijo THD at 41 , 1W <0.
INFORMAÇÕES SOBRE O PRODUTO Número do modelo Número de série Nome do revendedor Data de compra INTRODUÇÃO Agradecemos pela sua compra de um amplificador de ·áudio de alto desempenho MTX. Uma instalação bem feita com alto-falantes e subwoofers MTX oferece reprodução sonora e desempenho superiores para horas infindáveis de prazer, quer para acordar os vizinhos ou simplesmente para curtir suas músicas preferidas.
LAYOUT DO PAINEL 1 WHITE: L+ BRIDGE+ WHT/ BLK: L– GREY: R+ GREY/ BLK: R– BRIDGE– RED: 12V+ BLUE: REMOTE BL ACK: GND 2 3 LE VEL X-OVER FULL HI LOW MIN MA X MTX.
DIAGRAMA DE CONEXÃO Consulte a página 22 para os diagramas de conexão do amplificador. INSTALAÇÃO E MONTAGEM A MTX recomenda que o amplificador da Thunder Sports™ seja instalado por um revendedor MTX autorizado. Qualquer procedimento que não siga as instruções de instalação fornecidas pode causar graves danos ao amplificador, alto-falantes e/ou sistema elétrico do veículo. Danos causados por instalação incorreta NÃO estão cobertos pela garantia. Verifique todas as conexões antes de ligar o sistema. 1.
INSTALAÇÃO Para um desempenho adequado e Segurança MTX recomenda a instalação de um fusível em linha por Manual de Instruções do Proprietário de acordo com o seguinte. MUD100.
ESPECIFICAÇÕES Modelo MUD100.
INFORMATIONS SUR LE PRODUIT Modèle Nº de série Nom du détaillant Date d’achat INTRODUCTION Merci de votre achat de l’amplificateur audio MTX hautes performance. Son installation correcte associée à des haut-parleurs et des caissons de graves MTX vous apportera un son et des performances de qualité supérieure que vous apprécierez pendant des heures en diffusant de la musique pour le plaisir de vos voisins ou simplement de vous-même.
DISPOSITION DU PANNEAU 1 WHITE: L+ BRIDGE+ WHT/ BLK: L– GREY: R+ GREY/ BLK: R– BRIDGE– RED: 12V+ BLUE: REMOTE BL ACK: GND 2 3 LE VEL X-OVER FULL HI LOW MIN 18 MA X MTX.
SCHEMA DE CABLAGE Voir page 22 pour les schémas de câblage de l’amplificateur. INSTALLATION ET MONTAGE MTX conseille de confier l’installation de l’amplificateur Thunder Sports™ à un détaillant MTX agréé. Tout écart des instructions d’installation spécifiées peut entraîner de graves dommages à l’amplificateur, aux haut-parleurs et/ou au système électrique du véhicule. Les dommages entraînés par une installation incorrecte ne sont PAS couverts par la garantie.
INSTALLATION Pour la bonne exécution et de la sécurité MTX recommande d’installer un fusible en ligne par les instructions du mode d’emploi selon la formule suivante. MUD100.
CARACTERISTIQUES TECHNIQUES Modèle MUD100.2 Description 50 W eff. CH Stereo Puissance eff. à 14,4 V Charge 4 1 ponté 200 W eff. Charge 2 1 100 W eff. Charge 4 1 50 W eff.
WIRING DIAGRAM 41 Stereo WHITE: L+ BRIDGE+ W H T/ BL K : L – GRE Y: R+ GRE Y/ BL K : R – BRIDGE – RED: 12 V+ BLUE: REMOTE BL ACK : GND RCA Signal RCA Signal Remote Signal FUSE 4-Ohm 12V Source Unit 4-Ohm 22 MTX.
WIRING DIAGRAM 21 Stereo WHITE: L+ BRIDGE+ W H T/ BL K : L – GRE Y: R+ GRE Y/ BL K : R – BRIDGE – RED: 12 V+ BLUE: REMOTE BL ACK : GND RCA Signal RCA Signal Remote Signal FUSE 4-Ohm 12V Source Unit 4-Ohm 4-Ohm 4-Ohm MTX.
WIRING DIAGRAM 41 Bridged WHITE: L+ BRIDGE+ W H T/ BL K : L – GRE Y: R+ GRE Y/ BL K : R – BRIDGE – RED: 12 V+ BLUE: REMOTE BL ACK : GND RCA Signal RCA Signal Remote Signal FUSE 12V Source Unit 24 4-Ohm MTX.
© 2014 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. MTX004785 RevA 1/14 • 21A10131 • AW0014621 MTX.
OWNER'S MANUAL RZRXP-10 POLARIS® RZR® AMPLIFIED SUBWOOFER ENCLOSURE MTX.
IIIIIPOII7ANT NOTICE If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support at 1-800-225-5689. When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle's battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.
FEATURES • • • • • • 10" All-Weather Amplified Subwoofer Enclosure Integrated 250-Watt RMS I 500-Watt Peak Power Amplifier Integrated Power and Ground Connections Low Level Input with External Gain Control Dash Mount Bass Control Knob (Included) Mounts Underneath Dashboard- Direct Fit, No Drilling Required SPECIFICATIONS • RMS Power Handling: 250-Watts • Peak Power Handling: 500-Watts • Frequency Response: 34Hz- 120Hz MTX.
INSTALLATION Step 1 -Release the two quick locks to remove the hood from the vehicle. Step 2- Lift up the hood and slide towards the front of the vehicle. Step 3- Remove the two (2) T40 screws holding down the top dash cover. MTX .
Step 4- Lift and pull back the top dash cover to release the clips holding it in place. Unplug the gauge and switches making sure not to damage the vehicle and ignition wiring. Make note to remember what connector is associated with each specific switch. Step 5- Remove the Torx head screw from the dash pocket brace. After this is removed the plastic dash pocket and bracket can be pulled out of the dash. MTX .
Step 6- Remove the two (2) T40 screws holding the dashboard in place. Step 7- Pull the dashboard towards the back of the vehicle. There are locking clips on the right and left side that hold it in place. The dash will pop out. 6 MTX.
Step 8- Carefully lift the dash out of the vehicle. If the locking clips have fallen off, place them back onto the locking tabs on the dash. These are needed to re-assemble the dashboard. Step 9- Remove the two (2) 10mm hex bolts that are holding the glove box to the vehicle frame. When the screws are removed the glove box can be lowered down and out of the enclosure. Step 10- Remove the five (5) T25 screws holding the glove box together. The glove box will then open like a book. MTX .
Step 11 - Cut the "binding" plastic hinge with a razor knife to separate the front and back of the glove box. The back side of the glove box will no longer be used. The front side of the glove box will be attached to the enclosure. Step 12- Using the five (5) T25 screws that were removed from the front I back assembly of the glove box, attach the front of the glove box to the RZRXP-10 enclosure.
Step 14 - Hold the enclosure up and align the glove box screw holes with the vehicle frame mount. Replace the two (2) 10mm hex bolts and tighten the enclosure in place. It may help to place a supporting object under the enclosure so both hands are free to line up the screw holes with the vehicle frame mount. Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of the enclosure into place. The furthest hole to the right uses the included 1" screw.
Step 16- Now that the enclosure is securely tightened in place, the power and signal wires need to be connected to the battery and signal source. • The Red wire should be connected directly to the battery's positive terminal and fused with a 20A fuse. • The Black wire should be directly connected to the battery's negative terminal. •If your vehicle is equipped with the Polaris® buss bar kit, the Red and Black wires can be connected to the buss bar under the hood on the firewall.
© 2016 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
