Service Manifold Manual
Table Of Contents
- Technical Support
- Preface
- Introduction
- About the Hydraulic Service Manifold (HSM)
- 293.32 HSM Component Identification
- HSM Fluid Flow
- HSM Filtering
- HSM Pressure Control
- About HSM Pilot Pressure
- HSM Accumulators
- HSM Slow Turn-On
- HSM Rapid Pressure Reduction
- Model 239.32 HSM Hydraulic Schematic
- Model 293.32 HSM Dimensions
- Model 293.32 HSM Specifications
- Safety
- General Safety Practices: Hydraulic Power Units and Hydraulic Service Manifolds
- Hazard Placard Placement
- Read all manuals
- Locate and read hazard placards/labels
- Specimen Temperature Changes
- Know facility safe procedures
- Know controls
- Have first aid available
- Know potential crush and pinch points
- Be aware of component movement with hydraulics off
- Know electrical hazards
- Keep bystanders safely away
- Wear proper clothing
- Remove flammable fluids
- Check bolt ratings and torques
- Practice good housekeeping
- Protect hoses and cables
- Provide proper hydraulic fluid filtration
- Protect accumulators from moving objects
- Do not exceed the Maximum Supply Pressure
- Do not disable safety devices
- Use appropriately sized fuses
- Provide adequate lighting
- Provide means to access out-of-reach components
- Wear appropriate personal protection
- Handle chemicals safely
- Know system interlocks
- Know system limits
- Do not disturb sensors
- Ensure secure cables
- Stay alert
- Contain small leaks
- Stay clear of moving equipment/avoid crush points
- Know the causes of unexpected actuator motions
- Do not use RF transmitters
- Know compressed gas hazards
- General Safety Practices: Hydraulic Power Units and Hydraulic Service Manifolds
- Installation
- Operation
- Maintenance
©
2014 MTS Systems Corporation. All rights reserved.
Original Instructions (English): 015-081-200 F
Trademark Information
MTS, be certain., Bionix, ElastomerExpress, FlatTrac, FlexTest, Just In Case, LevelPlus, MTS Criterion,
MTS EM Extend, MTS Insight, MTS Landmark, RPC, ServoSensor, SWIFT, Temposonics, TestWare,
TestWorks are registered trademarks of MTS Systems Corporation within the United States. Acumen,
Advantage, Aero ST, Aero-90, AeroPro, Criterion, CRPC, Echo, Flat-Trac, Landmark, MAST,
MicroProfiler, MPT, MTS Acumen, MTS Echo, MTS Fundamentals, MTS TestSuite, ReNew, SilentFlo,
TempoGuard, TestLine, and Tytron are trademarks of MTS Systems Corporation within the United
States. These trademarks may be registered in other countries. All other trademarks are property of
their respective owners. All other trademarks are property of their respective owners.
Proprietary Software
Software use and license is governed by the MTS End User License Agreement which defines all
rights retained by MTS and granted to the End User. All Software is proprietary, confidential, and
owned by MTS Systems Corporation and cannot be copied, reproduced, disassembled, decompiled,
reverse engineered, or distributed without express written consent of MTS.
Software Verification and Validation
MTS software is developed using established quality practices in accordance with the requirements
detailed in the ISO 9001 standards. Because MTS-authored software is delivered in binary format, it
is not user accessible. This software will not change over time. Many releases are written to be
backwards compatible, creating another form of verification. The status and validity of the MTS operating
software is also checked during system verification and routine calibration of MTS hardware. These
controlled calibration processes compare the final test results after statistical analysis against the
predicted response of the calibration standards. With these established methods, MTS assures its
customers that MTS products meet exacting quality standards when initially installed and will continue
to perform as intended over time.
Manual Part Number—Publication Date—Release
015-081-200 F—March 2014
015-081-200 E—March 2008
015-081-200 D—May 2001
015-081-200 C—December 1996