DESIGNER COLLECTION Drop-in / Undermount / Alcove Whirlpool - Air Bath O P E R AT I O N A N D C A R E Effective May 1, 2014
OPERATING INSTRUCTIONS - KEYPAD & TUB CONTROL FUNCTIONS FOR WHIRLPOOLS AND AIR BATHS Keypads and functions will vary depending on specific model and/or options purchased. Use the drawings on the following pages to locate your model and simply follow the step by step instructions. #1 STANDARD AIR SYSTEM FUNCTIONS ON/OFF: 1st Press: The blower starts. LED light on. 2nd Press: The blower stops. LED light off. BLOWER SPEED INCREASE Press & hold to increase the blower speed.
#2 STANDARD WHIRLPOOL FUNCTIONS PUMP ON 1st Press: The pump starts. Use the air volume control to adjust. PUMP OFF 1st Press: The pump stops. # 3 STANDARD WHIRLPOOL / AIR BATH COMBINATION OR STREAM BATH WITH AIR SYSTEM FUNCTIONS ON/OFF PUMP 1st Press: The pump starts. Light on. 2nd Press: The pump stops. Light off. ON/OFF BLOWER 1st Press: The blower starts. Light on. 2nd Press: The blower stops. Light off. BLOWER SPEED INCREASE Press & hold to increase the blower speed.
# 4 AIR SYSTEM WITH LED LIGHT FUNCTIONS ON/OFF FOR AIR SYSTEM 1st Press: The blower turns on at 30% power. Use the up and down arrows to increase or decrease the speed. Please note: 20% is the minimum. If the lights for the up & down arrows go off, they can be reactivated by gently pressing the on/off button 2nd Press: The blower turns off. PULSATION MODE 1st Press: Standard wave. Speed will vary gradually from minimum to maximum. 2nd Press: Standard pulse.
# 4 AIR SYSTEM WITH LED LIGHTING AND RADIANCE R4 FUNCTIONS ON/OFF FOR RADIANCE SYSTEM:1st Press: Turns on both heated zones. Light on keypad will be on. 2nd Press: Turns off Radiance system. Light will be off. ON/OFF FOR AIR SYSTEM 1st Press: The blower turns on at 30% power. Use the up and down arrows to increase or decrease the speed. Please note: 20% is the minimum.
# 5 ULTRA THERAPY WHIRLPOOL WITH 12 OR MORE MICRO-JETS AND TSUBO MASSAGE FUNCTIONS ON/OFF PUMP FOR POINT MASSAGE JETS 1st Press: The pump starts. LED light on. 2nd Press: The pump stops. LED light off. ON/OFF PUMP FOR MICRO-JETS / TSUBO MASSAGE IMPORTANT! YOU MUST TURN THE VOLUME CONTROL FOR THE MICRO-JETS DOWN UNTIL YOU ARE SITTING IN FRONT OF THEM. IF ACTIVATED BEFORE, WATER MAY SPLASH OUTSIDE THE BATH. 1st Press: The Tsubo pump starts. LED light on. 2nd Press: The Tsubo pump stops. LED light off.
# 6 STANDARD WHIRLPOOL / AIR SYSTEM COMBINATION WITH LED LIGHTING FUNCTIONS OR STREAM BATH WITH AIR SYSTEM & LED LIGHTING ON/OFF FOR AIR SYSTEM 1st Press: The blower turns on at 30% power. Use the up and down arrows to increase or decrease the speed. Please note: 20% is the minimum. If the lights for the up & down arrows go off, they can be reactivated by gently pressing the on/off button 2nd Press: The blower turns off. PULSATION MODE 1st Press: Standard wave.
# 8 ULTRA THERAPY WHIRLPOOL / AIR SYSTEM COMBINATION FUNCTIONS ON/OFF PUMP FOR POINT-MASSAGE JETS 1st Press: The pump starts. LED light on. 2nd Press: The pump stops. LED light off. ON/OFF PUMP FOR MICRO-JETS / TSUBO MASSAGE IMPORTANT! YOU MUST TURN THE VOLUME CONTROL FOR THE MICRO-JETS DOWN UNTIL YOU ARE SITTING IN FRONT OF THEM. IF ACTIVATED BEFORE, WATER MAY SPLASH OUTSIDE THE BATH. 1st Press: The Tsubo pump starts. LED light on. Press & hold 1 second: The Tsubo pump stops. LED light off.
# 9 ULTRA THERAPY WHIRLPOOL / AIR SYSTEM COMBINATION WITH LED LIGHTING FUNCTIONS ON/OFF FOR AIR SYSTEM 1st Press: The blower turns on at 30% power. Use the up and down arrows to increase or decrease the speed. Please note: 20% is the minimum. If the lights for the up & down arrows go off, they can be reactivated by gently pressing the on/off button 2nd Press: The blower turns off. WHIRLPOOL PUMP ON/OFF - LARGE POINT-MASSAGE JETS 1st Press: The pump turns on.
ADDITIONAL SYSTEM INFORMATION TSUBO LOCK-OUT TIMER - SYSTEMS #5, #8 AND #9 The user is allowed to operate the Tsubo mode for a total of 30 minutes (two 15-minute cycles) before a lock-out of the Tsubo mode occurs. This is designed to avoid tripping the thermal protector in the motor. The details of the lock-out are as follows: • A total of two 15-minute cycles results in the Tsubo mode being locked out for two hours of cooldown time. 1 minute of Tsubo mode = 4 minutes of cool down time (cumulative).
INDEPENDENT CHROMATHERAPY SYSTEM KEYPAD FOR ALL TUBS WITHOUT LED LIGHT FUNCTION ON KEYPAD FUNCTIONS ON/OFF BUTTON: 1st Press: White light. LED light on (White is only available when the system is initially turned on). 2nd Press: Light off. LED light off. Press the on/off button - Light must be on for any mode to function. MODE BUTTON FUNCTIONS: 1st Press: Aqua-Blue-Green Cycle. - First cycle 1.5 seconds between color changes; then slows to 6 seconds between color changes.
WHIRLPOOL OPERATING INSTRUCTIONS 1. MTI whirlpool tubs are equipped with a factory installed on/off device. This eliminates the need for an external switch. Starting motor with no water in the tub could result in damage to the pump and internal seals and could void your warranty. 2. tub approximately 1" above highest jet. Do not start pump until tub has been filled to specified level. Fill Do not leave a filling or full tub unattended. 3.
OPTIONAL EQUIPMENT OPERATING INSTRUCTIONS INLINE HEATER For Whirlpools - The factory installed inline heater used on MTI whirlpool systems is designed to maintain the temperature of the water during the hydrotherapy bath. The heater is not designed to heat cold water. The heater will activate automatically when the pump is engaged. There is no separate control for the heater. The thermostat is pre-set at 102°F. The heater must be plugged into a110 VAC,15 AMP, GFCI protected outlet.
FILL-FLUSH SYSTEM OPERATING INSTRUCTIONS THE WHIRLPOOL SYSTEM SHOULD BE CLEANED PERIODICALLY. MTI BATHS RECOMMENDS CLEANING AT LEAST ONCE A MONTH, NOT TO EXCEED 90 DAYS BETWEEN CLEANINGS. ALWAYS USE CAUTION WHEN USING CHLORINE-BASED PRODUCTS IN CONJUNCTION WITH OTHER CLEANING PRODUCTS. THE POSSIBILITY OF HARMFUL FUMES COULD RESULT. ALWAYS RINSE THOROUGHLY. DO NOT LEAVE THE UNIT UNATTENDED DURING FILL-FLUSH OPERATIONS.
SIMPLE TOUCH SYSTEM OPERATING INSTRUCTIONS 1. After bathing, drain the bath as usual, leaving the drain open. 2. Close all point-massage and rotary jets. 3. Remove detergent dispenser cap. 4. Add one of the following into the detergent dispenser: 2 oz. of MTI Fresh Wave Cleaner, 1 cup of vinegar or a few drops of a low-sudsing liquid detergent mixed with 1 cup of warm water. For each method, follow with 1 cup of cool, clean water. 5. Replace the detergent dispenser cap. 6.
CLEANING INSTRUCTIONS FOR WHIRLPOOL SYSTEMS NOT EQUIPPED WITH THE OPTIONAL FILL-FLUSH OR SIMPLE TOUCH CLEANING SYSTEMS THE WHIRLPOOL SYSTEM SHOULD BE CLEANED PERIODICALLY. MTI BATHS RECOMMENDS CLEANING AT LEAST ONCE A MONTH, NOT TO EXCEED 90 DAYS BETWEEN CLEANINGS. ALWAYS USE CAUTION WHEN USING CHLORINE-BASED PRODUCTS IN CONJUNCTION WITH OTHER CLEANING PRODUCTS. THE POSSIBILITY OF HARMFUL FUMES COULD RESULT. ALWAYS RINSE THOROUGHLY.
