Specifications
Table Of Contents
- TABLE OF CONTENTS
- LOI
- LOT
- LAST CHANGE
- WARNING
- CHAPTERS
- FIGURES
- FIGURE 1-1
- FIGURE 1-1.1
- FIGURE 2-1
- FIGURE 2-2
- FIGURE 2-3
- FIGURE 2-4
- FIGURE 3-1
- FIGURE 5-1
- FIGURE 5-2
- FIGURE 5-3
- FIGURE 5-4
- FIGURE 5-5
- FIGURE 5-6
- FIGURE 5-7
- FIGURE 5-8
- FIGURE 5-9
- FIGURE 5-10
- FIGURE 5-11
- FIGURE 5-12
- FIGURE 5-13
- FIGURE 5-14
- FIGURE 6-1
- FIGURE 6-2
- FIGURE 6-3
- FIGURE 6-4
- FIGURE 6-5
- FIGURE 6-5.1
- FIGURE 6-7
- FIGURE 6-8
- FIGURE 6-9
- FIGURE 6-10
- FIGURE 6-10.1
- FIGURE 6-11
- FIGURE 7-1
- FIGURE 7-2
- FIGURE 7-3
- FIGURE 7-3.1
- FIGURE 7-4
- FIGURE 7-5
- FIGURE 7-6
- FIGURE 7-7
- FIGURE 7-8
- FIGURE 7-8.1
- FIGURE 7-9
- FIGURE 7-10
- FIGURE 7-11
- FIGURE 7-12
- FIGURE 7-13
- FIGURE 7-14
- FIGURE 7-15
- FIGURE 7-16
- FIGURE 7-17
- FIGURE 7-18
- FIGURE 7-19
- FIGURE 7-20
- FIGURE 7-21
- FIGURE 7-22
- FIGURE 7-23
- FIGURE 7-24
- FIGURE 7-25
- FIGURE 7-26
- FIGURE 7-27
- FIGURE 7-28
- FIGURE 7-29
- FIGURE 7-30
- FIGURE 7-31
- FIGURE 7-32
- FIGURE 7-33
- FIGURE 7-34
- FIGURE 7-35
- FIGURE 7-36
- FIGURE 7-37
- FIGURE 7-38
- FIGURE 7-39
- FIGURE 7-40
- FIGURE 7-41
- FIGURE 7-42
- FIGURE 7-43
- FIGURE 7-44
- FIGURE 7-45
- FIGURE 7-46
- FIGURE 7-47
- FIGURE 8-1
- FIGURE 8-2
- FIGURE 8-3
- FIGURE 8-4
- FIGURE 8-5
- FIGURE 9-1
- FIGURE 9-2
- FIGURE 10-1
- FIGURE 10-2
- FIGURE 10-3
- FIGURE 10-4
- FIGURE 10-5
- FIGURE 10-6
- TABLES
- APPENDIX A
- INDEX
- PAGES
- PAGE iv
- PAGE v
- PAGE vi
- PAGE 1-1
- PAGE 1-3
- PAGE 1-4
- PAGE 1-9
- PAGE 1-10.1
- PAGE 2-1
- PAGE 2-2
- PAGE 2-4
- PAGE 2-5
- PAGE 2-12
- PAGE 2-13
- PAGE 2-14
- PAGE 2-15
- PAGE 2-16
- PAGE 2-17
- PAGE 3-1
- PAGE 3-2
- PAGE 4-1
- PAGE 5-1
- PAGE 5-2
- PAGE 5-3
- PAGE 5-4
- PAGE 5-5
- PAGE 5-6
- PAGE 5-7
- PAGE 5-8
- PAGE 5-10
- PAGE 5-11
- PAGE 5-12
- PAGE 6-1
- PAGE 6-2
- PAGE 6-3
- PAGE 6-5
- PAGE 6-6
- PAGE 6-7
- PAGE 6-8
- PAGE 6-8.1
- PAGE 6-9
- PAGE 6-10
- PAGE 6-12
- PAGE 6-13
- PAGE 6-14
- PAGE 6-15
- PAGE 6-16.2
- PAGE 6-17
- PAGE 6-19
- PAGE 6-20
- PAGE 6-21
- PAGE 7-1
- PAGE 7-2
- PAGE 7-3
- PAGE 7-4
- PAGE 7-5
- PAGE 7-6
- PAGE 7-7
- PAGE 7-8
- PAGE 7-9
- PAGE 7-10
- PAGE 7-10.1
- PAGE 7-10.2
- PAGE 7-11
- PAGE 7-12
- PAGE 7-13
- PAGE 7-14
- PAGE 7-15
- PAGE 7-16
- PAGE 7-17
- PAGE 7-18
- PAGE 7-19
- PAGE 7-20
- PAGE 7-21
- PAGE 7-22
- PAGE 7-23
- PAGE 7-24
- PAGE 7-25
- PAGE 7-26
- PAGE 7-27
- PAGE 7-28
- PAGE 7-29
- PAGE 7-30
- PAGE 7-31
- PAGE 7-32
- PAGE 7-33
- PAGE 7-34
- PAGE 7-35
- PAGE 7-36
- PAGE 7-37
- PAGE 7-38
- PAGE 7-39
- PAGE 7-40
- PAGE 7-41
- PAGE 7-42
- PAGE 7-43
- PAGE 7-44
- PAGE 8-1
- PAGE 8-2
- PAGE 8-5
- PAGE 8-7
- PAGE 8-9
- PAGE 8-11
- PAGE 9-1
- PAGE 9-2
- PAGE 10-1
- PAGE 10-2
- PAGE 10-4
- PAGE 10-5
- PAGE 10-8
- PAGE 10-11
- PAGE 10-13
- PAGE 10-14
- PAGE 10-16
- PAGE A-1
- PAGE INDEX-1
The high temperature cutout switch must be
removed and tested semiannually (500 hours).
b.
Test.
(1) Using an oil pot tester and peanut oil, heat
Oil to 394° ± 10ºF (201° ± 5°C).
(2) Immerse threads and bottom surface of switch
in oil. After a minimum of 1 minute, use an ohm-
meter and check continuity between terminals on
switch.
TM5-6115-585-34
NAVFAC P-8-623-34
TO-35C2-3-455-2
TM-05684C/05685B-34
(3) If continuity exists, replace with a new switch.
(4) Keep threads and bottom surface of switch in
oil and allow it to cool to 300
o
F (149
o
C) minimum.
Repeat continuity check in (2) above.
(5) If continuity does not exist, replace with a
new switch.
c. Installation.
(1) Install switch (11) on engine and lock with
locking tab (12).
(2) Connect electrical leads (10) to switch ter-
minals.
(3) On ASK equipped generators, refer to Operator and
Organizational Maintenance Manual and replace top panel assembly
and exhaust plenum.
Change 6
3-3/(3-4 blank)