Operation Manual
English Operating instructions for lawn tractors
12
Cutters with cleaning nozzle
(optional)
Fig. 16
Place the appliance on an even
surface free of debris, stones, etc.,
and engage the locking brake.
1.Use a commercially available
quick-release coupling to attach
a water hose. Turn on water.
2.Start the engine.
3.Lower the cutters, and switch ON
for a few minutes.
4.Switch OFF the cutters and
engine.
5.Detach the water hose.
Repeat steps 1 to 5 for the second
cleaning nozzle (if provided).
At the end of cleaning (steps 1 to 5):
Raise the cutters to the top,
start the engine, and switch ON
the cutters for a few minutes
to dry them.
Cleaning accessories
See instructions in the operating
manual for the accessories.
Servicing the vehicle
Observe the servicing guidelines
in the engine manual.
At the end of the grass-cutting
season, have the appliance checked
and serviced in a specialist workshop.
`~ìíáçå
båÖáåÉ=çáä=áë=Ü~ò~êÇçìë=
íç=íÜÉ=ÉåîáêçåãÉåí
m~ëë=çå=~åó=ï~ëíÉ=çáä=ïÜ áÅÜ=Åçã Éë=
~Äçìí=íÜêçìÖÜ=~å=çáä=ÅÜ~åÖÉ =
íç=~=ÅçääÉÅíáçå=éçáåí=çê=~= ï~ëíÉ=
Çáëéçë~ä=Åçãé~åóK
oáëâ=çÑ=éçääìíáçå=Ñêçã=Ä~ííÉêáÉë
rëÉÇ=Ä~ííÉêáÉë=Çç=åçí=ÄÉ äçåÖ=
íç=ÇçJãÉëíáÅ=êìÄÄáëÜK=
m~ëë=çå=ìëÉÇ=Ä~ííÉêáÉë=íç=~ =ÇÉ~ äÉê=
çê ~=ï~ëíÉ=Çáëéçë~ä=Åçãé ~åóK=
aáëã~åíäÉ=íÜÉ=Ä~ííÉêó=ÄÉÑçêÉ=
íÜÉ îÉÜáÅäÉ=áë=ëÅê~ééÉÇK
Using jump leads
a~åÖÉê
kÉîÉê=ÄêáÇÖÉ=~=ÇÉÑÉ ÅíáîÉ=çê=ÑêçòÉ å=
Ä~ííÉêó=ïáíÜ=àìãé=äÉ~ÇëK=
båëìêÉ=íÜ~í=íÜÉ=ìåáíë=~åÇ=íÜÉ=àìãé=
äÉ~Ç=Åäáéë=Çç=åçí=íç ìÅÜ =É~Å Ü=çíÜÉê=
~åÇ=íÜ~í=íÜÉ=áÖåáíáçåë=~êÉ=ëïáíÅÜÉÇ=çÑÑK
Connect the red jump lead to the
positive terminal (+) of the flat
battery and the donor battery.
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine block
of the tractor with the flat battery
(as far away from the battery
as possible).
Note
If the donor battery is installed
in a vehicle, this vehicle must not
be started during the jump starting
process.
Start the tractor with the flat battery
and actuate the parking brake.
Disconnect the jump leads
in reverse sequence.
Tyre pressure
t~êåáåÖ
kÉîÉê=ÉñÅÉÉÇ=íÜÉ=ã~ñáãìã=éÉêãáíJ
íÉÇ=íóêÉ=éêÉëëìêÉ=Eë ÉÉ=ëáÇ É=ç Ñ íóêÉFK=
tÜÉå=éìãéáåÖ=ìé=íÜÉ=íóêÉëI=Çç= åçí=
ëí~åÇ=áå=Ñêçåí=çê=~ÄçîÉ=íÜÉ ãK
The recommended tyre operating
pressure is:
– front: 0.8 bar
– rear: 0.7 bar
Over-inflating reduces the longevity
of the tyres. Tyre pressure should
be checked before every journey.
After 5 operating hours
First engine oil change. See engine
manual for subsequent intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 17).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Clean battery terminals.
Change gear oil/gear oil filter
for the first time. This work should
be performed at a specialised
workshop.
Every 25 operating hours
Lubricate all cutter shafts, idlers,
and idler mounts with 251H EP
type grease applied to their
respective grease nipples.
This work should be performed
at a specialised workshop.
Lubricate the wheel bearings and
front wheel axes with 251H EP type
grease applied to their respective
grease nipples.
Lubricate wheels of the cutter
deck via the grease nipples using
a multi-purpose grease.
Lubricate steering shaft and stee-
ring housing via the grease nipples
using grease type 251H EP.
This work should be performed
at a specialised workshop.
Every 50 operating hours
Grass residue and other soiling
on the drive gears must be
removed at a specialised garage.
Change gear oil/gear oil filter.
This work should be performed
at a specialised workshop.
Every 2 months
For battery type 2 only – Fill battery
cells with distilled water up to 1 cm
beneath the filling aperture.
If necessary
Charging the battery
When the appliance is not used
for longer periods, we recommend
removing the battery from the appli-
ance and charging this before and
every two months during storage and
before the appliance is again put into
operation.
Note
Note the information in the operating
instructions for your battery charger.
Replace the fuse
Replace defect fuses only with
the equivalent rating.
Once a season
Apply multipurpose grease
to the teeth on the steering gear.
Lubricate the steering linkage
with a few drops of light oil.
Lubricate all moving parts and
bearing surfaces with a few drops
of oil (control levers, cutting height
adjustment).
Clean the spark plug and check
the gap between the electrodes
or replace the plug.
See engine handbook.