M4c,,.es )ff OPERATOR'S MANUAL Models 587 and 588 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimpr'oved forestcovered, brash-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used. it should be maintained in effective working order by the operator.
SECTION 1: FINDING YOUR MODEL NUMBER This Operator's Manual is an important part of your new edger. It will help you assemble, prepare and maintain your edger. Please read and understand what it says. Before you start to prepare your edger for its first use, please locate the model plate and copy the information from it in this Operators Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support department. • Every edger has a model plate.
SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR EDGER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL HEED ITS WARNING.
• Make sure engine is off and spark plug wire is disconnected when clearing jammed material from blade. • Do not attempt to remove cut material nor hold material to be CUt when engine is running or when cutting blade is moving, AFTER • After striking a foreign object, shut off the engine, make absolutely sure the blade and aU moving parts have completely stopped, disconnect the spark plug wire to prevent accidentaJ starting, then thoroughly inspect the unit for any damage.
SECTION 4: SET-UP INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT 3. GASOLINE or OIL. After setting up the unit, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. IMPORTANT: Perform clutch rod adjustment before operating the edger. Insert opposite end of clutch rod into the hole in the pivot arm extension. Affix with flat washer and hairpin clip provided. See Figure 1, Inset B.
SECTION 5" CONTROLS THROTrLE CONTROL The throttle control lever is located on the engine. It allows the engine to run and also stops the engine. Refer to Figure 5. BLADE CLUTCWDEPTH WARNING: IMPORTANT: CONTROL The blade clutch/depth control is designed to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the blade clutch/depth control, or use the edger if the control is not adjusted properly.
SECTION 6: OPERATION STOPPING THE ENGINE The operation of any edger can result in foreign objects being thrown into the eyes, which can result in severe eye damage, Always wear safety glasses or eye shields. We recommend wide vision safety mask for over spectacles or standard safety glasses. _lb OPERATING THE EDGER WARNING: may throw Injury. Keep and do not place. blade if blade Do is over concrete,and asphalt, ARNING: not engage lower rocks, etc.
Engine--Refer to engine manual for lubrication instructions. SECTION 8: MAINTENANCE WARNING: Disconnect the spark plug wire and ground against the engine before performing any adjustment, repairs or maintenance. Figure 8 4, ENGINE To edge along a curb, remove the hairpin clip from the right side of the front axle, slide the right wheel toward the left side of the unit and replace the hairpin clip. See Figure 9.
SECTION 9: OFF-SEASON STORAGE The following steps should be taken to prepare unit for storage, 4. 1. Clean and lubricate unit thoroughly. NOTE: When storing any type of power equipment 2, Refer to engine manual storage instructions. 3. Coat cutting blade with chassis grease prevent rusting. SECTION for 10: TROUBLE correct Trouble Possible Engine fails to start Dirty air cleaner. Choke not in CHOKE position. Fuel tank empty, or stale fuel.
Models 587 & 588 NOTE: Adjustable curb wheel is NOT standard on aft units. 25 24 71 97 99 / 94 100 7 IMPORTANT: 77 For a proper working machine, use Factory Approved Parts. V-BELTS are specially designed to engage and disengage safely. A substitute (non-OEM) V-Belt can be dangerous by not disengaging completely.
Models 587 & 588 Ref. No.
MANUFACTURER'S LIMITED WARRANTY FOR: )[[ For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective, in material or workmanship.
