OPERATOR'S MANUAL Front Tine Tiller Model Series 300 & 330 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest_ covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
TABLEOFCONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Assembling Your Tiller ....................................................................................... 5 Know Your Tiller ................................................................................................. 6 Operating Your Tiller ..........................................................................................
SECTION1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol-- heed its warning.
9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. Lookdownandbehindandusecarewhenin reverse orpullingmachine towards you. Starttheengine according totheinstructions found inthismanual andkeepfeetwellawayfromthe tinesatalltimes. Afterstriking a foreignobject,stoptheengine, disconnect thesparkplugwireandgroundagainst theengine. Thoroughly inspect themachine forany damage. Repairthedamage beforestartingand operating.
SECTION2: ASSEMBLING YOURTILLER NOTE: This operator's manual covers various models of tillers. The units illustrated may vary slightly from your unit. Follow only those instructions which pertain to your model number. .Handle Adjustment NOTE: References to right or left side of the tiller are determined from behind the unit in the operating position. ToRemoveUnitFromCarton Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.
CheckCableAdjustment With the clutch lever disengaged, pull starter rope slowly several times. The tines should not turn. If they turn, the cable is not adjusted properly. To adjust the cable, loosen the nut near the top of the cable and unscrew the cable to provide additional slack in wire. See Figure 3. Tighten the nut and check again for proper adjustment.
ChokeLever EngineControls The choke lever is located near the throttle control. It is See the separate engine manual for additional information and functions of the engine controls. used to enrich the fuel mixture when starting a cold engine. StarterHandle The starter handle is located on the engine and is used to manually start the engine.
ControllingSpeedAndTillingDepth Wheel YokeAdjustment Place wheel yoke so that the wheels are forward (nearest point between wheels and tines) for shallow tilling, cultivating and transport. The forward speed will increase. Turn yoke around (farthest point between wheels and tines) for deep tilling. Forward speed will decrease. See Figure 6.
working width of the machine is 22 or 24 inches. For cultivation, this may be reduced to 13 inches by removing the outer tines. Refer to the Adjustment Section. When laying out plant rows, be sure to allow enough width to permit cultivation between the rows. In growing corn or similar crops, check-row planting will permit cross cultivation and practically eliminate hand hoeing. See Figure 9. _q Figure 9 The tiller has many uses other than tilling and cultivating a garden.
SECTION6: MAINTAININGYOURTILLER CleaningTineArea WARNING: Disconnect the spark plug wire and ground it against the engine before performing any repairs or maintenance. Clean the underside of the tine shield after each use. The dirt washes off the tines easier if rinsed off immediately instead of after it dries. Always towel dry the tiller afterwards and apply a light coat of oil or silicone to prevent rusting or water damage.
We do not recommend the use of pressure washers to clean your unit. They may cause damage to electric components, spindles, pulleys, bearings or the engine. The use of pressure washers will result in shortened life and reduce -lex Screw serviceability. Refer to the engine manual for correct engine storage instructions. Wipe tines with oiled rag to prevent rust. Store tiller in a clean, dry area. Do not store next to corrosive materials, such as fertilizer.
SECTION7: TROUBLESHOOTING Problem Engine fails to start Engine runs erratic Engine overheats Tines do not engage Cause Remedy 1. 2. 3. Spark plug wire disconnected. Fuel tank empty or stale fuel. Throttle control lever not in correct 1. 2. 3. Connect wire to spark plug. Fill tank with clean, fresh gasoline. Move throttle lever to start position. 4. 5. starting position. (If equipped) Choke not in ON position. Blocked fuel line. 4. 5. Move lever to ON position. Clean fuel line. 6. 7.
Notes 13
ModelSeries300 & 330 2 9 \ \ 15 27 18 42 65" /59 39' \ 34 41/ \ :_o .
ModelSeries300 & 330 Ref. No. Part No. 1. 2. 720-0274 731-0473 Ref. No. Part Description Grip Clutch Grip Clutch Lever Part No. Part Description 34. 35. 36. 712-3004A 710-0599 Hex Washer Screw 1/4-20 x .500 Tine Shield 20" 711-0919 Flange Lock Nut 5/16-18 Belt Cover Belt 3. 686-0002 4. 649-0137 Handle Assembly 37_ 786-0035A 5. 712-0442 Hex Washer Screw 3/8-16 x 1.25 738-1225 746-1148 38. 39. 40. 710-0502A 6. 7.
ModelSeries300 ) 2 / p- 2 1 \ \ \ 7_ \ \ \ \ 6 \ \ 17 / ! 12 / / / 15 / / 13' ! 28 16
ModelSeries300 Ref. No. Part No. Ref. No. Part Description Part No. Part Description 1. 2. 734-1840 738-0929 Wheel 7 x 1.7 Shoulder Screw 17. 736-0406 Flat Washer .442 ID x 1.38 OD 18. 738-0843 Jack Shaft 3. 686-0081A 4. 714-0149B Wheel Bracket Assembly Cotter Pin 19. 20_ 613-0001A 713-0312 Sprocket Assembly Chain #420 x 46 Links 5. 6. 711-6415 736-0242 Clevis Pin 21. 613-0003A Input Shaft Assembly Bell Washer .340 ID x .872 OD 7. 8.
ModelSeries330 29 2 \ \ \ / \ / ..3 \ / / / 22 I I / / / 8/ 17 5 1_ 17 13 ,/ / /5 / / / 27 4 / 28 18 / /
ModelSeries330 Ref. No. Part No. Ref. No. Part Description 1. 2. 734-1781 738-0929 Wheel 8 x 1.75 18. Shoulder Screw 3. 686-0081A 4. 714-0149B Wheel Bracket Assembly Cotter Pin 19. 20. 5. 711-6415 Clevis Pin 6. 736-0242 Bell Washer .340 ID x .872 OD 7. 710-6189 8. 738-0934 9. Part No. 738-0843 613-0001A Part Description Jack Shaft 713-0312 Sprocket Assembly Chain #420 x 46 Links 21. 613-0003A Input Shaft Assembly 22. 23.
MANUFACTURER'S LIMITED WARRANTY The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the d. United States. its possessions and territories. MTD LLC warrants this product against defects for a period of FOR: MTD LLC does not extend any warranty for products sold or exported outside of the United States, its possessions and territories, except those sold through MTD LLC's authorized channels of export distribution. e.
