® Operator's Manual 27 Ton Log Splitter Model 570 IMPORTANT: Warning: Read safety rules and instructions This unit is equipped with an internal combustion carefully before operating equipment. engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
TABLEOFCONTENTS Content Page 3 5 7 8 Important Safe Operation Practices Assembling Your Log Splitter Know Your Log Splitter Operating Your Log Splitter Adjusting Your Log Splitter 10 Content Maintaining Your Log Splitter Storing Your Log Splitter Trouble Shooting Illustrated Parts List Warranty Page 10 12 12 14 16 FINDINGMODELNUMBER This Operator's Manual is an important part of your new log splitter. It will help you assemble, prepare and maintain the unit for best performance.
SECTION1: IMPORTANT SAFEOPERATION PRACTICES _ This and/or symbol property points out safety instructions which, notinstructions followed, could theARNING: personal safety of important yourself and others. Read and followif all in thisendanger manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
j, If gasoline is spilled, wipe it off the engine and equipment, move machine to another area. Wait 5 minutes before starting the engine. Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. Allow machine to cool 5 minutes before storing. Maintenance and Storage 1. 2. 3. Operation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
SECTION2: ASSEMBLING YOURLOGSPLITTER UnpackingfromCrate AttachingtheTongue • • • • • _ Pry top, sides, and ends off the crate. Set panels aside to avoid tire puncture or personal injury. Remove and discard plastic bag that covers unit. Remove any loose parts if included with unit (i.e., operator's manual, etc.) Cut and remove straps which secure parts to bottom of crate. Unbolt any remaining parts which may be bolted to the bottom of the crate. thisARNING: machine.
• Disconnect the log cradle from the beam on the side of the control valve. See Figure 4. PreparingtheLog Splitter • • Lock Washer Nut • Lubricate the beam area (where the splitting wedge will slide) with engine oil; do not use grease. Remove vented reservoir dipstick, which is located in front of the engine on top of the reservoir tank. See Figure 6. Fill the reservoir tank with Dexron III automatic transmission fluid or 10W AW hydraulic fluid. NOTE: The reservoir tank has a capacity of 3.5 gallons.
SECTION3: KNOWYOURLOGSPLITTER Compare the illustration in Figure 7 below with the controls on your log splitter, and get familiar with its features before starting to operate. Know how to stop the machine quickly in the event of an emergency. How it works / Handle _ Reverse " (Automatic) Log tTo r,eturn weage I Neutral I Assembly \\ Control Handle \\ To stop wedge I I/ Forward____ v To split (Manual) wood Jack Stand Beam Lock Cradle Beam Lock Tank Tail Light Horizontal Beam Lock Vertica
SECTION4: OPERATING YOURLOGSPLITTER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. WARNING: Wear leather work gloves, safety shoes, ear protection, and safety glasses when operating a log splitter. Ensure safe footing. GasandOilFill-Up • _ Service the engine with gasoline and oil as instructed in the engine manual packed with your log splitter. Read instructions carefully. handling gasoline.
• • Tolockthebeamintheverticalposition,pullouton theverticalbeamlockandrotateit tosecurethe beam.SeeFigure7. Standinfrontoftheunittooperatethecontrol handleandtostabilizethelog.SeeFigure8A. 8. RaisingandLoweringBeam • Use control handle to run wedge up and down beam 6 to 8 times to circulate the hydraulic fluid, which will warm and thin the fluid. • • Place log splitter on a firm, level surface. To raise the beam for vertical operation: Pull out the vertical beam lock on the tongue.
b. If coupler hitch is too loose on ball: Turn adjustment nut one turn clockwise. Connect the safety chains to the towing vehicle. Plug in the tail lights, if so equipped, to the tail light connector on the tow vehicle. _ andARNING: check local,Do state, not tow andfaster federal than 45mph requirements before towing on any public road. NOTE: Use caution when backing up. It recommended to use a spotter outside the vehicle.
• HydraulicFluid • Check the hydraulic fluid level in the log splitter reservoir tank before each use. • Maintain fluid level within the range specified on the dipstick at all times. Change the hydraulic fluid in the reservoir every 100 hours of operation. Disconnect the suction hose from the bottom of the reservoir tank and drain the fluid into a suitable • • • • • container. Refill using only Dexron III automatic transmission fluid or 10W AW hydraulic fluid.
SECTION7: STORINGYOURLOGSPLITTER Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more. _ • • • in the fuel tank inside WARNING: Never of store building machine where with fumes fuel may reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc. • • • • Clean the log splitter thoroughly.
HydraulicTroubleshooting Problem Cylinder rod will not move Slow cylinder shaft speed while extending and retracting. Cause Remedy 1. Broken drive shaft. 1. See authorized service dealer. 2. Shipping plugs left in hydraulic hoses. 2. 3. 3. 4. Set screws in coupling not adjusted properly. Loose shaft coupling. 5. 6. 7. 8. 9. 10. Gear sections damaged. Damaged relief valve. Hydraulic lines blocked. Incorrect oil level. Damaged directional valve. Blocked directional valve. 5. 6.
SECTION9: PARTSLISTFORMODEL570 1\ 16 29 26 28 \ 16 13 31 18 / C 65 A I 70 45 74 68 \\\\ 75 \ \\\ 77 \ 72 \ For Taillight. Ground Wire 78 48.. 82\ \ 81 \ 79 _ t If equipped 14
Model570 Ref. No. Part No. Ref. No. Part Description Part No. Part Description 1. 2. 718-0769 727-0634 Hydraulic Cylinder 44. 45. 781-0686 681-0161 Log Tray Bracket Hydraulic Tube 3. 710-1018 Hex Cap Screw 1/2-20 x 2.75 46. 726-0214 Push Cap 4. 737-0192 732-0583 5. 781-0526t 90 Degree Solid Adapter Hose Guard 47. 48. 710-0521 Compression Spring Hex Bolt 3/8-16 x 3" 6. 737-0153 Return Elbow 49. 781-0690 Lock Rod 7. 718-0481 Control Valve 50. 737-0348A 8. 9.
MANUFACTURER'S LIMITED WARRANTY FOR: ® The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. "Troy-Bilt" warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.
