MSE PSE-SW5F Series Power Source Equipment (Power over Ethernet Switch) PSE-SW5F-ST PSE-SW5F-SC PSE-SW5F-SFP USER’S MANUAL MSTRONIC CO., LTD.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP 1. General Information.............................................................. 3 2. Hardware Description........................................................... 3 LED Indicators...................................................................................... Power Wiring………………………………………………………………. Ethernet Port Wiring………………………………………………………. Fiber Port Wiring...................................................................................
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP 1. General Information The PoE (Power Over Ethernet) Switch supports four Fast Ethernet ports with PoE injector plus one 100Base-FX up-link port. The switch provides Power over Ethernet functions to deliver 35Watts of power budget per port to a powered device(PD), which is in compliance with IEEE802.3af/at standard to deliver both Ethernet data and DC48V power through the traditional UTP or STP cable to a PD.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP For PSE-SW5-SFP: LINK/ACT PoE Link/Act Indicator Indicator *POWER Indicator LED Power STATUS Green (PWR) Description LED ON if power input has valid power apply. Red LED ON if the following condition happens. *Power input under voltage (Vin<10V) *Power input over voltage (Vin>59V) *PoE over current(2.5A/per port) The indicator is used in current mode only. Off No power in DC input 4 MSTRONIC CO., LTD.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP *SWITCH Indicator (the right LED of RJ-45) LED P1~P5 STATUS Green Link/Act Description A network device is detected, but no communication activity is detected. Blinking This port is transmitting to, or receiving @43ms package from another device at 100Mbps. Blinking This port is transmitting to, or receiving @120ms package from another device at 10Mbps. Off No device is detected.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP For PoE (PSE) operation, the input voltage must be in the range of -42 to -60 VDC. Otherwise, the switch will function only as an Ethernet switch but will not provide any PoE power output. For PoE operation, make sure your 48 VDC supply is rated for at least 75 Watts for 4x 802.3af PoE port, or 150W for 4x 802.3at PoE port, plus some overhead for the switch.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP The following tables depict the wiring diagram of straight-through and crossover cabling. The crossover cables simply cross-connect the transmit lines at each end to the receive lines at the opposite end. Straight-through Cabling Pin 1 Pin 1 Pin2 Pin 2 Pin3 Pin 3 Pin6 Pin6 Cross-over Cabling Pin 1 Pin 3 Pin 2 Pin 6 Pin 3 Pin 1 Pin 6 Pin 2 7 MSTRONIC CO., LTD.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP Connect an Ethernet cable into any switch port and connect the other side to your attached device. The green Link/Act LED will light up when the cable is correctly connected. Refer to the LED indicator section for descriptions of each LED indicator. If a port LED is off, go back and check for connectivity problems between that port and the network device it is connected to.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP *PD Port Wiring Port 1 to port 4 provides PoE inject functionality with a maximum 35W ability to power up the powered device using the straight-through or cross-over Ethernet cable. The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following table shows pin assignments of alternative A and B for the Power Source Equipment.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP 3. Model Information Model Input Voltage Output voltage 802.3af/at PSE-SW5F-ST-S PSE-SW5F-SC-S PSE-SW5F-SFP-S 10-57VDC 10-57VDC (non-regulated) No (current mode) PSE-SW5F-ST24 PSE-SW5F-SC24 PSE-SW5F-SFP24 12-36VDC 56VDC (regulated) Yes (24V-802.3at mode) PSE-SW5F-ST48 PSE-SW5F-SC48 PSE-SW5F-SFP48 40-57VDC 40-57VDC (non-regulated) Yes (48V-802.3at mode) 10 MSTRONIC CO., LTD.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP 4. Technical Specifications Standards IEEE802.3/IEEE802.3u standards (10Base-T/100Base-T/100Base-FX) Ports 4 ports with 4 PoE(PSE), supports auto-crossover & auto-polarity, 1 port with the fiber connector Transmission speed 100Mbps(100Base-T), 10Mbps(10Base-T) Auto-negotiation Switch technology store-and-forward Protocols CSMA/CD Flow control IEEE802.
User’s Manual MSE PSE-SW5F-ST/-SC/-SFP *Fiber max. distance 2km(mm),15km(sm) Note: Other fiber connector and transmission distance are available. PoE port Port 1-4, auto power management Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8) Maximum PoE power Per port 35W PoE disconnect mode DC disconnect PoE auto detection IEEE802.
