WindBOX Series G52-9A151X1 i
Copyright Notice Th e material in this d ocument is the in tellectual p rop erty of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. Intel® and Pentium® are registered trademarks of Intel Corporation.
Safety Instructions 1. 2. 3. 4. 5. Always read the safety instructions carefully. Keep this user’s manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS. 6. Check the AC input: 100-240V~, 50-60Hz, 1.7A. 2.0A. 7. Check the DC output: 20V 8.
FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
WEEE (Waste Electrical and Electronic Equipment) Statement v
vi
vii
CONTENTS Copyright Notice ........................................................................................... Trademarks .................................................................................................. U.S. Patent Numbers .................................................................................... Revision History ........................................................................................... Technical Support ....................................................
Getting Started Chapter 1 Getting Started Congratulations for purchasing the WindBOX. This is your best choice for slim system. It can easily be set anywhere. The feature packed platform also gives you an exciting PC experience.
WindBOX Series System Specifications Processor - Intel® AtomTM processor N270 - Front Side Bus (FSB) 533 MHz - Thermal Design Power (TDP) 2.5 W - Highest Frequency Mode (HFM) 1.6 GHz - Lowest Frequency Mode (LFM) 800 MHz Chipset - North Bridge: Intel® 945GSE chipset - South Bridge: Intel® ICH7M chipset Display - Intel® GMA 950 chipset - Resolution is up to QXGA (2048 x 1536) Memory - Supports DDR2 400/ 533 SDRAM (200-Pin/ 1.
Getting Started Input/ Output (I/O) - 3 USB 2.0 ports - 1 Headphone / speaker connector (3.5mm) - 1 Mic connector (3.5mm) - 1 VGA connector - 1 RJ-45 LAN jack (by Realtek RTL8185E) - 1 3-in-l card reader (SD/MMC/MS) - 1 DC jack - 1 SMA connector for WLAN antenna Power Supply - 40 Watt Power Adapter with Active PFC - Input: 100-240V~, 50-60Hz 1.7A - Output: 20V, 2.0A Form Factor - 260 mm (W) X 180 mm (D) X 19 mm (H) - 1.
WindBOX Series System Outlooks Right Side View 1 2 7 3 4 5 6 Left Side View 8 10 6 1-4 9 1 RJ-45 Connector The connector is used to connect a LAN cable for network connection. 2 VGA Port The 15-pin-D-sub VGA port allows you to connect an external monitor or other standard VGA-compatible device (such as a projector) for a great view of the computer display. 3 Headphone Used for speakers or headphones. 4 Microphone Used for an external microphone.
Getting Started 7 Antenna Connector The connector allows you to connect an external antenna for wireless LAN. 8 Kensington Lock This system provides a Kensington Lock hole, which allows users to secure the system in place with a key or some mechanical PIN device and attached through a rubberised metal cable. The end of the cable has a small loop which allows the whole cable to be looped around a permanent object, such as a heavy table or other similar equipment, thus securing the system in place.
WindBOX Series Packing Contents WindBOX Power Adapter Power Cord Back Mount Package Driv er CD User Manual WLAN Antenna * Please contact us immediately if any of the item is damaged or missing. * The picture is for your reference only and your packing contents may slightly vary depending on the model you purchased.
System Assembly Chapter 2 System Assembly This chapter provides you with the information about system assemb l y p roced u res. Wh il e d oin g th e installation, be careful in holding the components and follow the installation procedures. Use a grounded wrist strap before handling computer comp on en ts. Static el ectricity may damag e th e components.
WindBOX Series Necessary Tools Cross type screwdriver, can be used to do most of the installation. Choose one with a magnetic head would be better. Rubber gloves, can prevent yourself from suffering the static charge. Assembly Procedures Important Choose the LCD less than 5.8 Kg for keeping the weight balance; otherwise, it may cause fall or related hazard. 1. Find the screw holes on the back of the LCD. 2. Use the corss-type screwdriver to fix the back mount plate with the attached screws.
System Assembly 3. Hang the system on the back mount plate. 4. The screw on the bottom of the back mount plate can be used to fasten the system. 5. Remove the protector from the WLAN antenna connector. 6. Install the attached WLAN antenna.
WindBOX Series 7. Connect the VGA cable between the system and the LCD. 8. Connect the adaptor the the system. 9. Turn on the system and enjoy it.
