Trident Series Personal Computer Trident B926 G52-B9261X4
Contents How to Use this Service Manual................................. 3 Necessary Tools........................................................ 3 Safety Precautions.................................................... 4 Other Notice.............................................................. 4 Upgrade and Warranty.............................................. 4 Acquisition of Replaceable Parts............................... 4 Arrow Used in This Manual........................................
Service Manual Important All information is subject to change without prior notice. The system photos are provided for demonstration of system disassembly only. The internal view of your system may vary depending on the model you purchased. hh How to Use this Service Manual This Service Manual is targeted for MSI-authorized dealer or service center. It provides in-depth illustration of disassembling the system.
hh Safety Precautions The following precautions should be observed while handling the system: ■■Place the system on a flat and stable surface. ■■Do not place the system in environments subject to mist, smoke, vibration, excessive dust, salty or greasy air, or other corrosive gases and fumes. ■■Do not drop or jolt the system. ■■Do not bump or knock the LCD screen as it is fragile and could break. ■■Do not use another power adapter other than the one enclosed with the system.
Service Manual hh Arrow Used in This Manual The red arrow shows the push or press direction. The yellow arrow remarks the position.
hh Right side cover 6 • 2.5” HDD • CPU & CPU Cooler • Memory Module Note: Product images are for illustrative purposes only and may differ from the actual product. hh Removing the right side cover Step 1. Place the system veritically on a flat and steady surface. Unlock the screws and keep the screws for later use. Important M3X4 screws * 2. Step 3. Draw and remove the upper cover carefully. Follow the above procedures in reversed order to replace the chassis.
Service Manual hh Installing 2.5” HDD Step 1. Put the bracket to the 2.5” HDD and lock the screws. Important M3X4 screws * 4. Step 2. Locate the HDD and connect the power and signal cables. 7 Step 3. Secure the bracket. Important M3X4 screws * 3.
hh Removing CPU Cooler (option 1) Step 1. Unlock screws of the CPU fan module. Important screws * 4. Step 2. Remove screws on the CPU thermal module. 8 Step 3. Unplug the power cable and the RGB LED cable. Follow the above procedures in reversed order to replace the CPU cooler.
Service Manual hh Removing CPU Cooler (option 2) Step 1. Unlock screws of the CPU fan module. Step 2. Unplug the power cable and the RGB LED cable. Follow the above procedures in reversed order to replace the CPU cooler.
hh Replacing CPU Alignment Key Alignment Key Yellow triangle is the Pin 1 indicator Retention tab Load plate Load lever 10 Retention knob Step 1. Push the load lever down to unclip it.
Service Manual Step 2. Lift the load plate to the fully open position. Step 3. Hold the CPU carefully or it may cause serious damages. Important Correct way. 11 Step 4. Align the notches with the socket alignment keys. Lower the CPU with thermal paste on straight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket. Important The correct position of the CPU.
Step 5. Close and slide the load plate under the retention knob. Step 6. Close and engage the load lever. Follow the above procedures in reversed order to uninstall the CPU.
Service Manual hh Installing Memory Module Step 1. Flip the slot clip outwards. Align the notch on the memory with the key on the slot and insert the memory into the slot with the correct orientation. Step 2. Push down the memory module gently until the slot clip is fastened. Push the memory module till it can not go futher. You will hear a "click". Important Push the memory gently downwards until the slot clip click and lock the memory in place.
hh Installing the right side cover Step 1. Close and push the cover outward as shown in the right. 1 Step 2. Lock the screws to finish. Important M3X4 screws * 2.
Service Manual hh Left side cover • Graphics Card • M.2 SSD Note: Product images are for illustrative purposes only and may differ from the actual product. hh Removing the left side cover Step 1. Place the system veritically on a flat and steady surface. Unlock the screws and keep the screws for later use. Important M3X4 screws * 2. Step 2. Draw and remove the upper cover carefully. Follow the above procedures in reversed order to replace the chassis.
hh Installing Graphics Card Step 1. Unlock the screws that secures the top cover. Important M3X4 screws * 2. Step 2. Open the top cover. 2 1 16 Step 3. Lock the screws of the auxiliary graphics card support to secure the bracket. Important M3X4 screws * 2. Step 4. Push the graphics card to the slot.
Service Manual Important When removing the graphics card, you need to press the clip to release it. Step 5. Lock the screws of the auxiliary graphics card support. Important 6-32 screws * 2. 17 Step 6. Lock the screws of the auxiliary graphics card support to finish. Important M3X4 screws * 4. Follow the above procedures in reversed order to remove the graphics card. Step 7. Connect the power connectors to finish.
Important Pictures of graphics card installation are for illustration purpose only. Actual procduct and its installation may vary due to product user purchased.
Service Manual hh Installing M.2 SSD (optional) Step 1. Locate the M.2 SSD slot. Step 2. Slide the M.2 SSD device by the direction as the figure shows. Important Align the notch on the M.2 SSD with the key on the slot and insert the SSD into the slot. Step 3. Push down the M.2 SSD device and lock it with the M2X4 screw. Important M2X4 screw * 1. Follow the above procedures in reversed order to remove the M.2 SSD.
hh Installing the left side cover Step 1. Close and push the cover outward as shown in the right. Step 2. Lock the screws to finish. Important M3X4 screws * 2.
