Specifications
XIO3130
www.ti.com
SLLS693F–MAY 2007–REVISED JANUARY 2010
Table 4-52. Bit Descriptions – Command Register
BIT FIELD NAME ACCESS DESCRIPTION
15:11 RSVD r Reserved. When read, these bits return zeros.
INTx disable. This bit is used to enable device-specific INTx interrupts. The XIO3130
downstream ports can generate INTx interrupts due to PCI Hot Plug events. The XIO3130
10 INT_DISABLE rw
forwards INTx messages from downstream ports to the upstream port (see INTx Support
section) regardless of this bit.
9 FBB_ENB r Fast back-to-back enable. This bit does not apply to PCI-Express, so it returns zero when read.
SERR enable. The relevant error checking is unnecessary for the XIO3130 internal PCI bus.
When set, this bit enables the transmission by the primary interface of ERR_NONFATAL and
8 SERR_ENB rw
ERR_FATAL messages forwarded from the secondary interface. This bit does not affect
transmission of ERR_COR messages.
7 STEP_ENB r Address/data stepping control. This bit does not apply to PCI-Express and is hardwired to 0.
Parity error response enable. This bit has no impact on hardware behavior. It is assumed that
6 PERR_ENB rw
the relevant error checking is unnecessary for the XIO3130 internal PCI bus.
VGA palette snoop enable. The XIO3130 does not support VGA palette snooping, so this bit
5 VGA_ENB r
returns zero when read.
Memory write and invalidate enable. This bit does not apply to PCI-Express, so it is hardwired to
4 MWI_ENB r
zero.
3 SPECIAL r Special cycle enable. This bit does not apply to PCI-Express and is hardwired to zero.
Bus master enable. When set, the XIO3130 is enabled to initiate cycles on the downstream PCI
Express interface.
0 – Downstream PCI Express interface cannot initiate transactions. The XIO3130 must
2 MASTER_ENB rw
disable response to memory and I/O transactions on the downstream interface.
1 – Downstream PCI Express interface can initiate transactions. The bridge can forward
memory and I/O transactions.
Memory response enable. Setting this bit enables the downstream port to respond to memory
1 MEMORY_ENB rw
transactions.
0 IO_ENB rw I/O space enable. Setting this bit enables the downstream port to respond to I/O transactions.
4.3.5 Status Register
The Status register provides information about the downstream port’s primary interface, i.e., the internal
PCI bus between the upstream and downstream ports.
PCI register offset: 06h
Register type: Read Only; Clear by a Write of One; Hardware Update
Default value: 0010h
BIT NUMBER 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RESET STATE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Table 4-53. Bit Descriptions – Status Register
BIT FIELD NAME ACCESS DESCRIPTION
Detected parity error. This bit is set when the virtual internal PCI interface receives a
poisoned TLP. This bit is set regardless of the state of the Parity Error Response bit in the
Command register.
15 PAR_ERR rcu
0 – No parity error detected.
1 – Parity error detected.
Signaled system error. This bit is set when the XIO3130 sends an ERR_FATAL or
ERR_NONFATAL message upstream and the SERR Enable bit in the Command register is
set.
14 SYS_ERR rcu
0 – No error signaled.
1 – ERR_FATAL or ERR_NONFATAL signaled.
Copyright © 2007–2010, Texas Instruments Incorporated XIO3130 Configuration Register Space 89
Submit Documentation Feedback
Product Folder Link(s): XIO3130