Optix Series LCD Monitor Optix MAG274QRF (3CA8) Optix MAG274QRF-QD (3CA8)
Contents Getting Started............................................................................................................... 3 Package Contents.................................................................................................... 3 Installing the Monitor Stand.................................................................................... 4 Adjusting the Monitor.............................................................................................. 5 Monitor Overview.....
Getting Started This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Installing the Monitor Stand 1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove. 2. Tighten the stand bracket with screws. 3. Connect the base to the stand and tighten the base screw to secure the base. 4. Make sure the stand assembly is properly installed before setting the monitor upright. ⚠⚠Important ∙∙ Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙∙ Do not use any sharp objects on the panel.
Adjusting the Monitor This monitor is designed to maximize your viewing comfort with its adjustment capabilities. ⚠⚠Important ∙∙ Avoid touching the display panel when adjusting the monitor. ∙∙ Please slightly tilt the monitor backwards before pivoting it.
Monitor Overview 1 2 4 3 5 6 Getting Started 6 6 7 8 9 10 10 11
1 Macro Key 2 Power Button 3 4 5 6 7 8 9 10 11 To activate OSD. Navi Key Kensington Lock DisplayPort HDMI Port USB Type-C Port This port supports DisplayPort Alternate (DP Alt) Mode and up to 5V/3A (15W) power delivery. It only carries video signals and doesn’t support data transmission function. Headphone Jack USB 2.0 Type B Upstream Port For USB Upstream Cable. ⚠⚠Important Check the package for USB Upstream Cable and connect it to the PC and monitor.
Connecting the Monitor to PC 1. Turn off your computer. 2. Connect the video cable from the monitor to your computer. 3. Assemble the monitor power adapter & power cord. (Figure A) 4. Connect the power adapter to the monitor power jack. (Figure B) 5. Plug the power cord into the electrical outlet. (Figure C) 6. Turn on the monitor. (Figure D) 7. Power on the computer and the monitor will auto detect the signal source.
OSD Setup This chapter provides you with essential information on OSD Setup. ⚠⚠Important All information is subject to change without prior notice. Navi Key The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.
OSD Menus Gaming 1st Level Menu Game Mode 2nd/3rd Level Menu Description FPS ∙∙ Use Up or Down Button to select and preview mode effects. User Racing RTS Night Vision RPG OFF Normal Strong ∙∙ All items can be adjusted by users. ∙∙ Press the OK Button to confirm and apply your mode type. ∙∙ This function optimizes background brightness and is recommended for FPS games. Strongest Response Time A.I. Normal Fast Fastest 10 OSD Menus ∙∙ Users can adjust Response Time in any mode.
1st Level Menu Anti Motion Blur Refresh Rate 2nd/3rd Level Menu OFF ON Location Alarm Clock ON Location Left Top Right Top Right Bottom Left Top Right Top Left Bottom Right Bottom OFF 15:00 30:00 ∙∙ When Anti Motion Blur is enabled, HDCR and Brightness cannot be enabled and will be grayed out. ∙∙ Response time will be grayed out while Anti Motion Blur is enabled. Left Bottom OFF Description Customize ∙∙ Anti Motion Blur has to be disabled while Adaptive-Sync is set to ON.
1st Level Menu Adaptive-Sync 2nd/3rd Level Menu OFF ON Description ∙∙ Adaptive-Sync prevents screen tearing. ∙∙ DisplayPort or HDMI default is OFF and can be adjusted ON/OFF in any mode, any resolution, any input source and any screen refresh rate. ∙∙ Anti Motion Blur will be disabled if Adaptive-Sync is enabled. Professional 1st Level Menu Pro Mode 2nd Level Menu Description Reader ∙∙ All items can be adjusted by users. User Cinema Designer Eye Saver OFF ON ∙∙ Default mode is User.
1st Level Menu Image Enhancement 2nd Level Menu OFF Weak Medium Strong Description ∙∙ Image Enhancement enhances image edges to improve their acutance. ∙∙ Users can adjust Image Enhancement in any mode. Strongest Image 1st Level Menu Brightness 2nd/3rd Level Menu 0-100 Contrast 0-100 Sharpness 0-5 Color Temperature Screen Size ∙∙ Users can adjust Contrast in any mode. ∙∙ Users can adjust Sharpness in any mode. ∙∙ Sharpness improves clarity and details of images.
Input Source 1st Level Menu HDMI1 2nd Level Menu Description OFF ∙∙ Users can use the Navi Key to select Input Source at below status: HDMI2 ∙∙ Users can adjust Input Source in any mode. DP Type C Auto Scan ON • While “Auto Scan” is set to “OFF” with the monitor at power saving mode; • While “No Signal” message box is shown on the monitor. Navi Key 1st Level Menu Up / Down / Left / Right 2nd Level Menu Description Brightness ∙∙ Down Button default is Screen Assistance.
Setting 1st Level Menu Language 2nd Level Menu Description English ∙∙ Users have to press the OK Button to confirm and apply the Language setting. 繁體中文 Français Deutsch Italiano Español ∙∙ Language factory default is English. ∙∙ Language is an independent setting. Users’ own language setting will override the factory default. When users set Reset to Yes, Language will not be changed.
1st Level Menu HDMI CEC 2nd Level Menu Description ON ∙∙ HDMI CEC (Consumer Electronics Control) supports Sony PlayStation®, Nintendo® Switch™, and various audio-visual devices that are CEC-capable. OFF ∙∙ Default is OFF. ∙∙ If HDMI CEC is set to ON: • The monitor will automatically power on when the CEC device is turned on. • The CEC device will enter power saving mode when the monitor is turned off.
Specifications Model Optix MAG274QRF Curvature Flat Size Panel Type Resolution Aspect Ratio Brightness (nits) Brightness: USB Type-C Power Delivery 27 inch Rapid IPS 2560 x 1440 @165Hz 16:9 300 (typ.
Model Optix MAG274QRF Adjustment (Pivot) -90° ~ 90° Adjustment (Swivel) Kensington Lock Yes ∙∙ Plate Type: 100 x 100 mm ∙∙ Screw Type: M4 x 10 mm • Thread Diameter: 4 mm VESA Mounting • Thread Pitch: 0.7 mm Dimension (W x H x D) Weight Environment -75° ~ 75° Operating Storage • Thread Length: 10 mm 614.9 x 532.7 x 206.7 mm 6.05 Kg (net) / 8.
Preset Display Modes Standard VGA Resolution 640x480 @60Hz @67Hz @72Hz Dos-Mode 720x480 SVGA 800x600 720x576 @75Hz @60Hz @50Hz @56Hz @60Hz @72Hz XGA 1024x768 SXGA 1280x1024 WXGA+ 1440x900 Full HD 1920x1080 WSXGA+ QHD 1680x1050 2560x1440 @75Hz @60Hz @70Hz @75Hz @60Hz @75Hz @60Hz @60Hz @60Hz @120Hz @165Hz @60Hz @120Hz @144Hz Video Timing Resolution 480P 576P 720P 1080P 1080P @120Hz 2160P @30Hz 2160P @60Hz @165Hz Optix MAG274QRF / Optix MAG274QRF-QD HDMI DP/ Type-C V V V V V
Troubleshooting The power LED is off. • Press the monitor power button again. • Check if the monitor power cable is properly connected. No image. • Check if the computer graphics card is properly installed. • Check if the computer and monitor are connected to electrical outlets and are turned on. • Check if the monitor signal cable is properly connected. • The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.
Safety Instructions ∙∙ Read the safety instructions carefully and thoroughly. ∙∙ All cautions and warnings on the device or user’s manual should be noted. ∙∙ Refer servicing to qualified personnel only. ∙∙ Keep the User’s Guide that comes with the package for future reference. ∙∙ To prevent fire or shock hazard, keep this device away from humidity and high temperature. ∙∙ Lay this device on a reliable flat surface before setting it up.
Regulatory Notices CE Conformity This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.
WEEE Statement Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life. Chemical Substances Information In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No.
Green Product Features ∙∙ Reduced energy consumption during use and stand-by ∙∙ Limited use of substances harmful to the environment and health ∙∙ Easily dismantled and recycled ∙∙ Reduced use of natural resources by encouraging recycling ∙∙ Extended product lifetime through easy upgrades ∙∙ Reduced solid waste production through take-back policy Environmental Policy ∙∙ The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
