User's Manual

ManualsBrandsMSI ManualsComputersLGA 1200 ATX Motherboard

Table Of Contents

Quick Start
- Preparing Tools and Components
- Safety Information
- Installing a Processor
- Installing DDR4 memory
- Connecting the Front Panel Header
- Installing the Motherboard
- Connecting the Power Connectors
- Installing SATA Drives
- Installing a Graphics Card
- Connecting Peripheral Devices
- Power On
Specifications
- JCORSAIR1 Connector Specification
Package contents
Block Diagram
Rear I/O Panel
- LAN Port LED Status Table
- Audio Ports Configuration
- Realtek Audio Console
- Installing Antennas
Overview of Components
- CPU Socket
- DIMM Slots
- PCI_E1~5: PCIe Expansion Slots
- M2_1~2: M.2 Slots (Key M)
- SATA1~6: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- JAUD1: Front Audio Connector
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- JUSBC1: USB 3.2 Gen 2 10Gbps Type-C Connector
- JUSB3: USB 3.2 Gen 1 5Gbps Connector
- JUSB1~2: USB 2.0 Connectors
- JTPM1: TPM Module Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JTBT1: Thunderbolt Add-on Card Connector
- JRTD3: Intel RTD3 Connector
- JRGB1: RGB LED connector
- JRAINBOW1~2: Addressable RGB LED connectors
- JCORSAIR1: CORSAIR Connector
- EZ Debug LED
- LED_SW1: EZ LED Control
Installing OS, Drivers & Utilities
- Installing Windows® 10
- Installing Drivers
- Installing Utilities
UEFI BIOS
- BIOS Setup
- Entering BIOS Setup
- Resetting BIOS
- Updating BIOS
- EZ Mode
- Advanced Mode
- SETTINGS Menu
- OC Menu
- M-FLASH Menu
- OC PROFILE Menu
- HARDWARE MONITOR Menu
RAID Configuration
- Enabling Intel® Rapid Storage Technology
- Creating RAID Volume
- Removing a RAID Volume
- Resetting Disks to Non-RAID
- Rebuilding RAID Array
- Installing RAID Driver
- Installing Intel® Rapid Storage Technology Software
Intel® Optane™ Memory Configuration
- System Requirements
- Installing the Intel® Optane™ memory
- Removing the Intel® Optane™ memory
Troubleshooting
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
CPU_PWR1~2, ATX_PWR1: Power Connectors
CPU Socket
DIMM Slots
JAUD1: Front Audio Connector
JBAT1: Clear CMOS (Reset BIOS) Jumper
JCI1: Chassis Intrusion Connector
JCOM1: Serial Port Connector
JCORSAIR1: CORSAIR Connector
JFP1, JFP2: Front Panel Connectors
JRAINBOW1~2: Addressable RGB LED connectors
JRGB1: RGB LED connector
JRTD3: Intel RTD3 Connector
JTBT1: Thunderbolt Add-on Card Connector
JTPM1: TPM Module Connector
JUSB1~2: USB 2.0 Connectors
JUSB3: USB 3.2 Gen1 Connector
JUSBC1: USB 3.2 Gen 2 Type-C Connector
LED_SW1: EZ LED Control
M2_1~2: M.2 Slots (Key M)
PCI_E1~5: PCIe Expansion Slots
SATA1~6: SATA 6Gb/s Connectors

Overview of Components

M2_1~2: M.2 Slots (Key M)

Installing M.2 module

1. Loosen the screws of M.2 SHIELD FROZR heatsink.

2. Remove the M.2 SHIELD FROZR and remove the protective films from the thermal

pads.

M2_1

M2_2

⚠

Important

∙

Intel

RST only supports PCIe M.2 SSD with UEFI ROM.

∙

Intel

Optane™ Memory Ready for all M.2 slots.

⚽

Video Demonstration

Watch the video to learn how to Install

M.2 module.

http://youtu.be/JCTFABytrYA