Modern Series LCD Monitor Modern MD241P (3PA5) Modern MD271P (3PA4) Modern MD271QP (3PA4)
Contents Getting Started............................................................................................................... 3 Package Contents.................................................................................................... 3 Installing the Monitor Stand.................................................................................... 4 Adjusting the Monitor.............................................................................................. 5 Monitor Overview.....
Getting Started This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Installing the Monitor Stand 1. Leave the monitor in its protective foam packaging. Align the stand to the monitor groove. Push the stand towards the monitor groove until it locks in place. 2. Connect the base to the stand and tighten the base screw to secure the base. 3. Make sure the stand assembly is properly installed before setting the monitor upright. ⚠⚠Important ∙∙ Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙∙ Do not use any sharp objects on the panel.
Adjusting the Monitor This monitor is designed to maximize your viewing comfort with its adjustment capabilities. ⚠⚠Important ∙∙ Avoid touching the display panel when adjusting the monitor. ∙∙ Please slightly tilt the monitor backwards before pivoting it.
Monitor Overview Modern MD241P / Modern MD271P 1 2 4 6 Getting Started 3 5 6 7
Modern MD271QP 1 2 5 1 Power Button 3 Kensington Lock 2 4 5 6 7 8 3 4 8 6 7 OSD Keys USB Type-C Port This port supports DisplayPort Alternate (DP Alt) Mode and up to 5V/3A (15W) power delivery. It only carries video signals and doesn’t support data transmission function.
Connecting the Monitor to PC 1. Turn off your computer. 2. Connect the video cable from the monitor to your computer. 3. Connect the power cord to the monitor power jack. (Figure A) 4. Plug the power cord into the electrical outlet. (Figure B) 5. Turn on the monitor. (Figure C) 6. Power on the computer and the monitor will auto detect the signal source.
OSD Setup ⚠⚠Important This chapter provides you with essential information on OSD Setup. All information is subject to change without prior notice. OSD Keys The monitor comes with a set of OSD Keys that help to control the On-Screen Display (OSD) menu.
OSD Menus Press the M key to launch the On-Screen Display (OSD) main menu and use the OSD keys to tune the desired function to suit your personal preferences. 1st Level Menu 2nd/3rd Level Menu Description Contrast 0-100 DCR ON ∙∙ Adjusting display contrast. This function is available in Standard mode. Brightness 0-100 OFF Return Mode Exit ∙∙ When DCR is enabled, Contrast, and Brightness cannot be adjusted and will be grayed out. ∙∙ When DCR is enabled, Color Temp. will be set to Warm.
1st Level Menu Color Temp.
1st Level Menu Other 2nd/3rd Level Menu Language (More languages coming soon) English Deutsch Description ∙∙ Selecting the OSD language Français Italiano Español Русский Return Power Off Exit ON OFF Return Reset Exit YES NO Return OD Exit OFF Normal Extreme Return Volume Eco Mode Exit ON OFF ∙∙ Turning off the monitor after saving power for 1 minute ∙∙ Deactivating the timed switch-off function ∙∙ Resetting and restoring settings to original OSD defaults ∙∙ Deactivating the response t
Specifications Model Size Panel Type Resolution Modern Modern 23.8 inch 27 inch MD241P Contrast Ratio 1000:1 Response Time Input Interface 75 Hz 5 ms ∙∙ HDMI Port x1 ∙∙ USB Type-C (DP Alt Mode) x 1 (Up to 5V/3A power delivery) 178°(H) , 178°(V) Surface Treatment Anti-glare Display Colors Speaker 2 x 1W Power Input 100~240Vac, 50~60Hz, 1.5A Max Adjustment (Tilt) Adjustment (Swivel) ∙∙ DP x1 ∙∙ USB Type-C (DP Alt Mode) x 1 (Up to 5V/3A power delivery) 16.7 Million 19.
Modern Model Adjustment (Pivot) Adjustment (Height) Kensington Lock -90° ~ 90° Modern MD271QP 0 ~ 110 mm Yes Plate Type: 75 x 75 mm • Thread Pitch: 0.7 mm Weight Operating Storage • Thread Length: 10 mm 541.9 x 380.9 x 200.8mm 613.5 x 401.5 x 200.8mm 6.5Kg (Gross) 8.4Kg (Gross) 4.7Kg (Net), 5.
Preset Display Modes Modern MD241P / Modern MD271P Standard VGA Dos-Mode SVGA Resolution 640x480 720x400 720x480 720x576 800x600 XGA 1024x768 SXGA 1280×720 1280x1024 WXGA+ WSXGA+ Full HD Video Timing Resolution 1440x900 1680x1050 1920x1080 480P 576P 720P 1080P @60Hz @72Hz @75Hz @70Hz @60Hz @50Hz @60Hz @72Hz @75Hz @60Hz @75Hz @50Hz @60Hz @60Hz @75Hz @60Hz @60Hz @50Hz @60Hz @75Hz HDMI Type-C V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
Modern MD271QP Standard Resolution VGA 640x480 @60Hz Dos-Mode 720x400 @70Hz SVGA 720x480 720x576 800x600 XGA 1024x768 SXGA 1280×720 1280x1024 WXGA+ WSXGA+ Full HD 1440x900 1680x1050 1920x1080 2560x1440 Video Timing Resolution 480P 576P 720P 1080P 16 Preset Display Modes @75Hz @60Hz @50Hz @60Hz @75Hz @60Hz @75Hz @50Hz @60Hz @60Hz @75Hz @60Hz @60Hz @50Hz @60Hz @60Hz @75Hz HDMI DP Type-C V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
Troubleshooting The power LED is off. • Press the monitor power button again. • Check if the monitor power cable is properly connected. No image. • Check if the computer graphics card is properly installed. • Check if the computer and monitor are connected to electrical outlets and are turned on. • Check if the monitor signal cable is properly connected. • The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.
Safety Instructions ∙∙ Read the safety instructions carefully and thoroughly. ∙∙ All cautions and warnings on the device or User Guide should be noted. ∙∙ Refer servicing to qualified personnel only. Power ∙∙ Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet. ∙∙ If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug.
California, USA: The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California. For further information please visit: https://dtsc.ca.gov/perchlorate/ Environment ∙∙ To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators. ∙∙ Use this device only on a hard, flat and steady surface.
TÜV Rheinland Certification TÜV Rheinland Low Blue Light Certification Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light. ∙∙ Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.
Regulatory Notices CE Conformity This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.
WEEE Statement Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life. Chemical Substances Information In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No.
Green Product Features ∙∙ Reduced energy consumption during use and stand-by ∙∙ Limited use of substances harmful to the environment and health ∙∙ Easily dismantled and recycled ∙∙ Reduced use of natural resources by encouraging recycling ∙∙ Extended product lifetime through easy upgrades ∙∙ Reduced solid waste production through take-back policy Environmental Policy ∙∙ The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
