User's Manual
Table Of Contents
- Quick Start
- Specifications
- Package contents
- Block Diagram
- Rear I/O Panel
- Overview of Components
- CPU Socket
- DIMM Slots
- PCI_E1~4: PCIe Expansion Slots
- M2_1~2: M.2 Slots (Key M)
- SATA1~6: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- JUSB1~2: USB 2.0 Connectors
- JUSB3~4: USB 3.2 Gen 1 5Gbps Connectors
- JUSB5: USB 3.2 Gen 2 10Gbps Type-C Connector
- JAUD1: Front Audio Connector
- JTBT1: Thunderbolt Add-on Card Connector
- JRTD3: Intel RTD3 Connector
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- EZ Debug LED
- JRGB1~2: RGB LED connectors
- JRAINBOW1~2: Addressable RGB LED connectors
- Installing OS, Drivers & Utilities
- BIOS Setup
- AMD RAID Configuration
- Troubleshooting
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- CPU Socket
- DIMM Slots
- JAUD1: Front Audio Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JFP1, JFP2: Front Panel Connectors
- JRAINBOW1~2: Addressable RGB LED connectors
- JRGB1~2: RGB LED connectors
- JRTD3: Intel RTD3 Connector
- JTBT1: Thunderbolt Add-on Card Connector
- JUSB1~2: USB 2.0 Connectors
- JUSB3~4: USB 3.2 Gen1 Connectors
- JUSB5: USB 3.2 Gen 2 Type-C Connector
- M2_1~2: M.2 Slots (Key M)
- PCI_E1~4: PCIe Expansion Slots
- SATA1~6: SATA 6Gb/s Connectors
53
BIOS Setup
▶ Ipv4 PXE Support [Enabled]
When Enabled, the system UEFI network stack will support Ipv4 protocol. This item
will appear when Network Stack is Enabled.
[Enabled] Enables the Ipv4 PXE boot support.
[Disabled] Disables the Ipv4 PXE boot support.
▶ Ipv6 PXE Support [Enabled]
When Enabled, the system UEFI network stack will support Ipv6 protocol. This item
will appear when Network Stack is enabled.
[Enabled] Enables the Ipv6 PXE boot support.
[Disabled] Disables the Ipv6 PXE boot support.
▶ SATA Mode [AHCI Mode]
Sets the operation mode of the onboard SATA controller.
[AHCI Mode] Specify the AHCI mode for SATA storage devices. AHCI (Advanced
the speed and performance of SATA storage device, such as Native
Command Queuing (NCQ) and hot-plugging.
[RAID Mode] Enables RAID function for SATA storage devices.
▶ SATAx Hot Plug [Disabled]
Allows user to enable or disable the SATA hot plug support.
[Enabled] Enables hot plug support for the SATA ports.
[Disabled] Disables hot plug support for the SATA ports.
▶ HD Audio Controller [Enabled]
▶ Integrated Graphics Conguration (optional)
Adjusts integrated graphics settings for optimum system. Press Enter to enter the
sub-menu.
▶ Initiate Graphic Adapter [PEG] (optional)
Selects a graphics device as the primary boot device.
[IGD] Integrated Graphics Display.
[PEG] PCI-Express Graphics Device.
▶ Integrated Graphics [Auto] (optional)
If set to Force, BIOS will enable the integrated graphics controller.
▶ UMA Frame Buffer Size [Auto] (optional)
item will be available when Integrated Graphics is enabled.
▶ USB Conguration
Sets the onboard USB controller and device function. Press Enter to enter the sub-
menu.
▶ XHCI Hand-off [Enabled]