Hetis H81 Personal Computer MS-B073 System G52-B0731X1
Preface Contents Copyright Notice ���������������������������������������������������������������������������������������������iii Trademarks ����������������������������������������������������������������������������������������������������iii Revision ���������������������������������������������������������������������������������������������������������iii Upgrade and Warranty ���������������������������������������������������������������������������������� iv Acquisition of Replaceable Parts �������
Hetis H81 Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. ￭ ￭ ￭ ￭ ￭ MSI is a registered trademark of Micro-Star Int’l Co., Ltd.
Preface Upgrade and Warranty Please note that certain components preinstalled in the product may be upgradable or replaceable by user’s request. To learn more about upgrade limitation, please refer to the specifications in the User’s Manual. For any further information about the product users purchased, please contact the local dealer. Do not attempt to upgrade or replace any component of the product if you are not an authorized dealer or service center, since it may cause the warranty void.
Hetis H81 Green Product Features ◙ ◙ ◙ ◙ ◙ ◙ Reduced energy consumption during use and stand-by Limited use of substances harmful to the environment and health Easily dismantled and recycled Reduced use of natural resources by encouraging recycling Extended product lifetime through easy upgrades Reduced solid waste production through take-back policy Environmental Policy ◙ ◙ ◙ ◙ The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
Preface Safety Instructions Read the safety instructions carefully and thoroughly. All cautions and warnings on the equipment or user’s manual should be noted. Keep the User’s Guide that comes with the package for future reference. Keep this equipment away from humidity and high temperature. Lay this equipment on a reliable flat surface before setting it up.
Hetis H81 Never pour any liquid into the opening that could damage or cause electrical shock. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the metal shield is reliably connected to protective earthing system of the building.
Preface CE Conformity Hereby, Micro-Star International CO., LTD declares that this device is in compliance with the essential safety requirements and other relevant provisions set out in the European Directive. FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Hetis H81 WEEE Statement (English) Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
Preface (Greek) (Ελληνικά) Σύμφωνα με την Οδηγία 2002/96/ΕΚ της Ευρωπαϊκής Ένωσης («ΕΕ») περί Απόρριψης Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (WEEE), η οποία λαμβάνει ισχύ στις 13 Αυγούστου 2005, τα προϊόντα «ηλεκτρικού και ηλεκτρονικού εξοπλισμού» δεν είναι δυνατόν να απορριφθούν πλέον ως κοινά απορρίμματα και οι κατασκευαστές κεκαλυμμένου ηλεκτρονικού εξοπλισμού είναι υποχρεωμένοι να πάρουν πίσω αυτά τα προϊόντα στο τέλος της ωφέλιμης ζωής τους.
Hetis H81 (Indonesia) (Bahasa Indonesia) Sesuai dengan Regulasi Uni Eropa (“UE”) perihal WEEE (Limbah Peralatan Listrik dan Elektronik), Directive 2002/96/EC, yang berlaku sejak 13, 2005, produk “peralatan listrik dan elektronik” tidak lagi dapat dibuang sebagai sampah umum dan pabrik peralatan elektronik diwajibkan untuk mengambil kembali produk tersebut pada saat masa pakainya habis.
Preface (Danish) (Dansk) I henhold til direktiv fra den europæiske union (EU) vedrørende elektrisk og elektronisk affald , Direktiv 2002/96/EC, som træder i kraft den 13. august 2005, må produkter som “elektrisk og elektronisk udstyr” ikke mere bortskaffes som kommunalt affald. Producenter af det pågældende, elektroniske udstyr vil være forpligtet til at tage disse produkter tilbage ved afslutningen på produkternes levetid.
Chapter 1 Overview Congratulations for purchasing the Hetis H81 (MS-B073) System. This system is your best slim PC choice. With the fantastic appearance and ultrasmall form factor, it can easily be set anywhere. The feature packed platform also gives you an exciting PC experience.
Overview Packing Contents Hetis H81 Stand Driver/ Utility Disk User Manual AC Power Cord 1-2 * Please contact us immediately if any of the items is damaged or missing. * The illustrations are for reference only and your packing contents may slightly vary depending on the model you purchased.
Hetis H81 System Overview Front View 6 1 2 3 7 4 5 1-3 1 Headphone Jack This connector is provided for headphones or speakers. 2 Microphone Jack This connector is provided for microphones. 3 USB 3.0 Port The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard, mouse, or other USB-compatible devices. It supports up to 5Gbit/s (SuperSpeed) data transfer rate. The USB 3.0 port is backward-compatible with USB 2.0 devices.
Overview 5 Hard Disk Drive LED This indicator shows the activity status of the HDD. It flashes when the system is accessing data on the HDD and remains off when no disk activity is detected. 6 Optical Disk Drive A DVD Super-Multi drive is integrated for your home entertainment. (Blu-ray is optional.) 7 Eject Button Press the eject button to open and close the optical disk drive. Important High-speed devices are recommended for USB 3.
Hetis H81 Rear View 2 1 5 3 7 4 6 8 10 12 9 11 13 1 Power Jack Power supplied through this jack supplies power to your system. 2 Power Switch Press the power switch to turn the power supply on and off. The “on” position is the solid line and the “off” position is the circle. Make sure the power supply switch to the “on” position before you press the power button to turn on your system.
Overview 5 LAN Jack The standard RJ-45 LAN jack is provided for connection to the Local Area Network (LAN). You can connect a network cable to it. Yellow LED Color LED State Condition Left Yellow Off LAN link is not established. On (steady state) LAN link is established. On (brighter & pulsing) The computer is communicating with another computer on the LAN. Off 10 Mbit/sec data rate is selected. On 100 Mbit/sec data rate is selected. On 1000 Mbit/sec data rate is selected.
Hetis H81 12 HDMI Port The High-Definition Multimedia Interface (HDMI) is an all-digital audio/ video interface capable of transmitting uncompressed streams. HDMI supports all TV format, including standard, enhanced or high-definition video, plus multi-channel digital audio on a single cable. 13 Audio Jack Line-In (Blue) is used for external CD player, tapeplayer or other audio devices. Line-Out (Green) is used for speakers or headphones. Mic (Pink) is used for microphones.
Overview Component Replacement & Upgrade Please note that certain components preinstalled in the product may be upgradable or replaceable by user’s request depending on the models users purchased. 1-8 To learn more about upgrade limitation, please refer to the specifications in the User’s Manual. For any further information on the product users purchased, please contact the local dealer.
Chapter 2 Getting Started This chapter provides you with the information on hardware setup procedures. While connecting peripheral devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Getting Started Safety & Comfort Tips The Hetis H81 is a portable platform that allows you to work anywhere. However, choosing a good workspace is important if you have to work with your PC for a long period of time. 1� Your work area should have enough illumination. 2� Choose the proper desk and chair and adjust their height to fit your posture when operating. 3� When sitting on the chair, sit straight and keep a good posture. Adjust the chair’s back (if available) to support your back comfortably.
Hetis H81 Connecting Peripheral Devices The I/O (input/output) ports on the rear panel allow you to connect peripheral devices. All devices listed here are for reference only. Connecting Serial Devices Serial ports are commonly used in applications such as industrial automation systems, scientific analysis, shop till systems and some industrial/consumer products. Users may connect barcode scanners, barcode printers, bill printers, and credit card machine to this serial port.
Getting Started Connecting VGA-Out & HDMI-Out Devices This Hetis H81 provides a VGA port and an HDMI port for connection to external monitors, projectors, set-top boxes, DVD players, digital video cameras, mini notebooks, digital cameras, etc. VGA (Video Graphics Array) is a graphics display system for PCs. VGA connectors and their associated cabling are always used solely to carry analog video signals along with digital clock and data.
Hetis H81 Connecting the USB Devices This Hetis H81 provides USB ports for connecting various USB devices, such as mouse, keyboard, digital camera, webcam, printer, external optical storage device,.. and etc. To connect these devices, install the drivers for each device first if necessary, and then connect the device to the Hetis H81.
Getting Started Connecting the Network Device The RJ-45 connector of the Hetis H81 allows you to connect the LAN (local area network) devices, such as a hub, switch and gateway, to build a network connection. For more instructions or detailed steps on connecting to the LAN, please ask your MIS staff or network manager for help.
Hetis H81 Connecting the External SATA Hard Disk Drive The eSATA Connector allows you to connect an external Serial ATA hard disk device. The eSATA standard interface supports “plug-and-play” technology, so that you can connect and remove the eSATA devices without turning off the Hetis H81. To connect the eSATA hard disk device, simply connect the cable of the device to the eSATA Connector of your Hetis H81.
Getting Started Hardware Setup Connecting the AC Power 1. Unpack the package to find the AC power cord. Plug one end of the AC power cord to the Hetis H81. 2. Plug the male end to the electrical outlet. Disconnecting the AC Power 3. Unplug the AC power cord from the electrical outlet first. 4. Unplug the AC power cord from the Hetis H81. 1 2-8 2 4 3 Important When unplugging the AC power cord, always hold the connector part of the cord.
Chapter 3 System Operations This chapter provides you with essential information on system operations. Important All information is subject to change without prior notice.
System Operations Power Management Power management of personal computers (PCs) and monitors has the potential to save significant amounts of electricity as well as deliver environmental benefits. To be energy efficient, turn off your display or set your PC to sleep mode after a period of user inactivity. Power Management in Windows 7 ■ 3-2 [Power Options] in Windows OS allow you to control the power management features of your display, hard drive, and battery.
Hetis H81 ■ The Shut Down Computer menu presents the options of Sleep (S3/S4) & Shut Down (S5) for rapid and easy management of your system power. Power Management through ENERGY STAR qualified monitors (Optional) The power management feature allows the computer to initiate a low-power or “Sleep” mode after a period of user inactivity. When used with an external ENERGY STAR qualified monitor, this feature also supports similar power management features of the monitor.
System Operations Network Connection (Windows 7) Wired LAN 1. Go to [Start] > [Control Panel]. 2. Select [Connect to the Internet] under [Network and Internet]. 3-4 3. Select [Broadband (PPPoE)] to connect using DSL or cable that requires a user name and password. 4. Type the information from your Internet Service Provider (ISP) and click [Connect] to establish your LAN connection.
Hetis H81 Network Connection (Windows 8) Wired LAN 1. Go to [Start] > [Control Panel]. 2. Select [View network status and tasks] under [Network and Internet]. 3-5 3. To establish a new connection, select [Network and Sharing Center]. 4. Select [Set up a new connection or network].
System Operations 5. Choose [Connect to the Internet]. 6. Select [Broadband (PPPoE)] to connect using DSL or cable that requires a user name and password. 7. Type the information from your Internet Service Provider (ISP) and click [Connect] to establish your LAN connection.
Hetis H81 System Recovery (Windows 7) Important The Recovery Tool is only available on systems bundled with Windows OS and MSI utilities by default. The purposes for using the Recovery Tool may include: ■ ■ ■ ■ Restore the system back to the initial status of original manufacturer’s default settings. When some errors have occurred to the operating system in use. When the operating system is affected by virus and is not able to work normally. When you want to install the OS with other built-in languages.
System Operations 3. Enter the Recovery Tool. This tool contains three features: Backup System, Restore System and Recover to factory default. System Backup It is highly recommended that users back up the system as the solution in the event of a catastrophic disk failure or other accidents. 3-8 Follow the instructions below to continue: 1. Select [Backup System] to enter. Alternatively, select [X] or press [Esc] on the keyboard to exit.
Hetis H81 2. Select [BACKUP] to start the system backup immediately. The Initial Backup The initial backup may take a while. Please let it complete without interruption. Subsequent Backups Subsequent backups will replace the previous backup files.
System Operations 3. The system backup is in progress. Please note that it may take a while. Do not switch off the power, or it may cause unknown damage to the system. 4. Alternatively, select [CANCEL] to stop the system backup immediately. Please do not switch off the power while the system backup cancellation is in progress.
Hetis H81 5. The following message indicates a successful system backup. Press [OK] to finish. System Restore This tool helps to return the system to a previous state with the backup files that users created and saved in the hard disk drive beforehand. If no backup files are available, the system will be restored to the default setup. Follow the instructions below to continue: 1. Select [Restore System] to enter. Alternatively, select [X] or press [Esc] on the keyboard to exit.
System Operations 2. Select [OK] or [NEXT] so that the system can recover to the previous backup or default setup. Alternatively, select [CANCEL] to stop the system restore immediately.
Hetis H81 3. The system restore is in progress. Please note that it may take a while. Do not switch off the power, or it may cause unknown damage to the system. 4. The following message indicates a successful system restore. Press [OK] to finish. Restart the system and access the Windows operating system as usual. If the restore process fails or is interrupted, please start the whole procedure all over again.
System Operations System Recovery This tool helps to recover the system back to factory default settings. All data on the HDD will be erased while all settings will be restored to factory default. Follow the instructions below to continue: 1. Select [Recover to factory default] to enter. Alternatively, select [X] or press [Esc] on the keyboard to exit. 3-14 2. The system will be recovered to factory settings. All data will be gone. Make sure all important data have been backed up.
Hetis H81 3. Please select [OK] so that the system can recover its default setup. 4. The system recovery is in progress. Please note that it may take a while. Do not switch off the power, or it may cause unknown damage to the system.
System Operations 5. The following message indicates a successful system recovery. Press [OK] to finish. Restart the system and access the Windows operating system as usual. If the recovery process fails or is interrupted, please start the whole procedure all over again.
Hetis H81 System Recovery (Windows 8) Important The System Recovery Function is only available on systems bundled with Windows OS and MSI utilities by default. The purposes for using the System Recovery Function may include: ■ ■ ■ ■ Restore the system back to the initial status of original manufacturer’s default settings. When some errors have occurred to the operating system in use. When the operating system is affected by virus and is not able to work normally.
System Operations Recovering the System with the Recovery Discs This section is meant for users to restore your system with the recovery discs that you created beforehand. Follow the instructions below to continue: 1. Insert the recovery disc into the optical disc drive. on Desktop, then “Change PC settings” to enter PC settings 2. Select [Settings] main page > General > Advanced startup, and click [Restart now] to restart the system. 3-18 3.
Hetis H81 4. Select recovery disc the boot device. 5. Press any key to reconfirm the selection when the following message appears. 6. The Windows OS starts loading files. 3-19 7. The system recovery menu pops up. [Hard Disk Recovery] will format the whole HDD. All data on the HDD will be erased while all settings will be restored to manufacturer default. Select [Hard Disk Recovery] only when your HDD is infected with fatal viruses and no solution can be found except a clear cleanup of the HDD.
System Operations [System Partition Recovery] will format the C drive only. Only the C drive will be restored to manufacturer default. Other drives will not be affected. It is highly recommended that users select [System Partition Recovery] to restore the system. 8. The system recovery will format your HDD partition. Make sure that the important data have been backed up. Click [YES] to continue; click [NO] to stop the system recovery.
Hetis H81 10. The following message indicates successful system recovery. Press [OK] to restart the system and access the Windows operating system as usual. 11. If the recovery process is interrupted or failed, please repeat the recovery procedures from the beginning.
System Operations Recovery from the Operating System Refresh PC The Refresh PC utility checks whether the system files, Windows registry, and other important system components are working fine or not; on finding issues with Windows files, it will attempt to repair your PC. If your PC isn’t running well, you can refresh it without losing your personal files. 1.
Hetis H81 3. A message indicates that your PC is ready to be refreshed, click [refresh] to start. This might take a while. 4. After the refresh process ends, you will be back to Windows Start Screen where you can find all default Windows 8 utilities and widgets.
System Operations Reset PC The Reset utility will bring the system back to original factory settings. on Desktop, then “Change PC settings” to enter PC settings 1. Select [Settings] main page > General > Remove everything and reinstall Windows, and click [Get started]. 3-24 2. It will show the changes to be made during the process, click [Next] to continue.
Hetis H81 3. You will be prompted to choose which drive you want to clean for a hard disk with multiple partitions. 4. Now, select either to remove files or to fully clean drives according to your needs. 3-25 5. It is now ready to reset your PC, click [Reset] and follow the on-screen instructions to restart your PC.
