Cassette Remote Manual

6
12
13
TURBO Button(RG05F2/BGEU1)
Active/Disable Turbo function.
TURBO/IONIZER Button(RG05F3/BGEU1)
Active/Disable Turbo function. Holding this
button down for 2 seconds will activate the
Ionizer function.
Turbo function enables the unit to reach the
preset temperature at cooling or heating
operation in the shortest time(if the indoor unit
does not support this function, there is no
corresponding operation when this button is
pressed.)
When the Ionizer function is initiated, the
Ionizer/Plasma Dust Collector(depending on
models) is energized and will help to remove
pollen and impurities from the air.
LED Button
Disable/Active indoor screen Display.
11
DOWN Button
Push this button to decrease setting temperature
or to decrease Hour during Clock time setting.
NOTE: Press and hold UP and DOWN buttons
together for 3 seconds will alternate the
temperature display between the
O
C &
O
F
scale.
13
TIMER ON Button
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
TIMER OFF Button
15
Press this button to activate the Auto-o time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-o time setting, just press the button until
the time setting is 0.0.
CLOCK Button
Used to set the remote clock.
16
3
MODE FAN SPEED
SWING V SLEEP
TIMER ON
TIMER OFF
CLOCK
RESET LOCK
M
AUTO
COOL
DRY
HEAT
FAN
4
5
7
8
9
10
11
12
13
14
15
2
1
TURBO
LED
SWING H
16
SELF CLEAN
6
I FEEL
14
RG05F3/BGEFU1
IONIZER
Function buttons (continued)
5
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN SPEED Button
9
10
UP Button
Push this button to increase setting temperature
or to increase Hour during Clock time setting.
8
LOCK Button
Press this recessed button to lock all current
settings, and the remote control will not
accept any operation except that of the LOCK.
Use the LOCK mode when you want to prevent
settings from being changed accidentally.
Press the LOCK button again to cancel the
LOCK function. A lock symbol will appear on
the remote controller display when the lock
function is activated.
7
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the control will return to the initial settings.
3
MODE FAN SPEED
SWING V SLEEP
TIMER ON
TIMER OFF
CLOCK
RESET LOCK
M
AUTO
COOL
DRY
HEAT
FAN
4
5
7
8
9
10
11
12
13
14
15
2
1
TURBO
LED
SWING H
16
SELF CLEAN
6
I FEEL
When the I FEEL function is activated, the
remote displays the actual temperature of its
location. The remote control will send this
signal to the air conditioner every 3 minutes
interval until the I FEEL button is pressed again.
This indicator light “ ” remains on.
The I FEEL function is not available under
DRY and FAN mode.
Switching the operation mode or turning o the
unit will cancel the I FEEL function automatically.
Under SELF CLEAN mode, the air conditioner
will automatically clean and dry the Evaporator
and keep it fresh for the next operation.
I FEEL /SELF CLEAN Function
Press this button less than 2 seconds will
initiate I FEEL function. And if this buttom
tis held for more than 2 seconds, the
SELF CLEAN function is initiated.
6
® ®
For more info visit www.mrcool.com For more info visit www.mrcool.com