Installation Sheet

9
Installing the junction box
Functions of the junction box:
1.
Allows precisely location of the ChromaSteam3 fixture within the steam
room ceiling.
2.
Provides a secure and easily identifiable holder for the control cable
while the steam room is being constructed.
3.
Works with the ChromaSteam3 fixture’s retention springs to prevent the
fixture from falling and injuring a person in the enclosure.
Locating the fixture:
1.
Locate the fixture in a location for optimal lighting within the enclosure.
2. ChromaSteam3 is for mood lighting only. Not to be used as a primary
lighting source.
3.
Do not locate the fixture in direct shower spray, near direct steam emis-
sion, or in any location where a lighting fixture may be damaged.
To install the junction box:
1.
Remove the two screws from the interior clips of the junction box, and
hand-screw them into the wings of the junction box (Figure 7).
2.
Remove one of the four knockouts from the junction box (Figure 7). The
resulting hole will allow routing of the 30-foot control cable into the junc-
tion box.
3.
Locate the two tabs on the junction box, and line them up against a ceil-
ing joist. The tabs locate the junction box proud of (slightly raised from)
the joist. Screw the two screws into the ceiling joist to secure the junc-
tion box (Figure 8).
4.
Route one end of the 30-foot control cable through the knockout into
the junction box, and fasten it to one of the interior clips to hold it in
place (Figure 9). Note that both ends of the control cable are the same.
5.
After the junction box is completely installed, ensure that you create
an opening in the steam room ceiling that aligns with the junction box
(Figure 10).
• Installation to be performed by
a qualified and licensed electri-
cian.
• Shock hazard. Ensure that
power is turned off during
installation. Turn off power at
breaker panel.
• To prevent leaks, do not install
the ChromaSteam3 fixture
where direct contact with
steam emission or water spray
could occur.
• The ChromaSteam3 fix-
ture is not intended to be
installed underwater. To
prevent leaks, do not install
the ChromaSteam3 fixture
in a location where it could
become submerged.
• The ChromaSteam3 fixture is
not rated for insulation con-
tact. Insulation must be a mini-
mum of 3” away from all sides
of the ChromaSteam3 fixture
assembly to prevent damage
to the fixture.
• Be careful not to strain, staple, pinch, or otherwise damage
the cable.
• Route cable as required to permit replacement.
• Cable should be run in dedicated conduit to facilitate installa-
tion, service, and replacement.
• To prevent damage to the cable, do not route cable close to
hot water, steam piping, or any heat source.
WARNING
!
NOTICE
NOTICE
mr
.
steam
®
INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam
®
3
Failure to use the junction box
with correctly installed reten-
tion springs may result in the
ChromaSteam3 fixture falling
and causing injury.
CAUTION
!
IMPORTANT NOTE
Contact MrSteam to purchase an optional 60-foot cable (Part No.
104268-60).
INSTALLER
REFER
1.1.
Rem
Rem
han
han
TO
ove
the
ove the
-
screw
t
screw t
INSTALLATION,
wo
screws
from
the
interior
clips
of
the
ju
wo screws from the interior clips of the
e
m into the win
g
s o
f
the
j
unction box (
em into the wings of the junction box
F
OPERATION
ction
box,
and
ction box, and
g
ure 7
gure 7
).)
AND
•
To
preve
o preve
t
he Chr
o
the Chro
MAINTENANCE
t
leaks
,
do
not
installt leaks, do not install
m
aSteam3 fixture
maSteam3 fixtur
A
MANUAL
th
e
f
our
k
noc
k
ou
t
s
f
ro
the four knockouts f
will allow routing of the
will allow routing of the
PROVIDED
th
e
j
unc
ti
on
b
ox
(
the junction box (
Fig
ure
7Figure 7
)
)
0
-
foot control cable into the
0-foot control cable into the
WITH
Th
e
The
unc
unc
--
PRODUCT
where
direct
contac
where direct conta
steam em
i
ss
i
on or
w
steam emission o
P
P
FOR
h
h
COMPLETE
bdlh
bdlh
INSTRUCTIONS
ll
could
occur.could occur.
•
The ChromaS
The ChromaS
C