Butler/Butler2/ButlerX Linear iTempo Plus Control Linear SteamHead SteaLinx Mobile App MS / Super AutoFlush MX AutoFlush Condensation Pan PUR100474 PUR100561-1 PUR100518 PUR100200E PUR100532 TS0012 06-15 02-19 01-18 10-15 02-19 02-19 2019-03-14
Installation, Operation & Maintenance Manual ™ ™ iTEMPO & iTEMPOPLUS CONTROLS mr.steam ® Feel Good Inc. www.mrsteam.
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS 2. ! WARNING Do not permit children under the age of 16 to use this steambath. 3. ! WARNING Steam is hot and can cause injury or death if improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room. 4.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® REA D ME F IR S T ! Table of Contents: ! WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and operation of this generator. These are types of potential hazards that may occur during installation and operation: Important Safety Instructions...............................
mr Installation & Operating Instructions .steam ______________________________________________________________ ® BEFORE INSTALLING Carefully inspect the control and packaging for shipping damage. In the event of shipping damage, please contact the carrier for claim information. Our customer service department can assist you with any missing or damaged parts. per instructions for the Remote Temperature Probe.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Dimensional Information for the Round and Square iTempo™ and iTempoPlus™ Box Contents: • iTempo™ or iTempoPlus™ Control • Control Cable (30 ft.) • Steam head • Tube of Silicone Sealant • Owner’s Manual 41/2” 1” 3/8” 21/2” 5” 1/4” 5” 3/ ” 33/ ” 4 4 12” long pigtail 5 Drawings for Illustrative Purposes Only.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Installation Instructions for Round & Square iTempo™ and iTempoPlus™ 2-5⁄8” Step 1 Determine the desired installation location of the control. The iTempo™ and iTempoPlus™ controls are designed to be installed inside or outside the steam room as a matter of personal preference.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® NOTE: The connector is keyed with the flat facing up. The control cable is the same at both ends. important NOTE: Be careful not to strain, staple, pinch or otherwise damage the control cable. Route cable as required to permit replacement. Do not route cable inside conduit together with power lines or close to hot water or steam piping.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Step 6 Diagram 5 Run a bead of silicone (provided) as shown to the outer edge of the control faceplate, following the contour of the circle or square shape. Use silicone as required to create a moisture seal. Note: The silicone supplied by Mr. Steam can be used to meet a variety of sealing and gasketing.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Installing the Remote Temperature Probe (PN: MSTS) The Remote Temperature Probe is required when the iTempo or TempoPlus Controls are installed outside the steam room. d. The probe has an integral 30’ cable. Insure that the probe and/or steam generator are located accordingly. 2. Drill a 5/16 inch diameter hole in the wall. Do not oversize or under size the hole. Clean area thoroughly.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Temperature Probe Connection Diagram 1 Knock-Out Temperature Probe Cable (30 feet) Mr.Steam Steam Generator Temperature Sensor Probe (shown with cover removed and NOT installed) 10 Drawings for Illustrative Purposes Only.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® steam room interior 5. Route the end of the probe cable with the temperature probe through the wall into the steam room as shown in Diagram 2. DIAGRAM 2 important note: Do not strain, staple, pinch or otherwise damage the probe cable. 6. With a minimal length of the cable exposed apply silicone (provided) to the hole in the wall as required to create a moisture seal as shown in Diagram 2.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® iTempo™ Operating Instructions The iTempo Control features programmable digital temperature control, a fixed (60) minute duration, ON/OFF and PAUSE.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Timer Feature When the control is turned ON a 60 minute time duration is initiated. The control will turn off after 60 minutes unless the control is turned off manually. Memory Feature If the control is turned off manually before 60 minutes then the default temperature of 110˚F will be used the next time the control is turned on.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® iTempoPlus™ Operating Instructions The iTempoPlus Control features programmable temperature control, programmable time duration, clock, AromaSteam, ChromaSteam®, ON/OFF and two personal settings.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Setting the Clock Diagram 3 When the display is not flashing: Press and hold the TIME key until the display starts flashing. Use the UP/DOWN keys to select the desired time, at this time the AM/PM logo will be displayed. Press the TIME key to save changes. Note: The clock can only be set when the generator is off.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Setting the Temperature Diagram 6: Press TEMP key to set the desired temperature or display the temperature setting. Diagram 7: The control is preset and will display a temperature setting of 110˚F (default setting). With the temperature displayed, press the UP or DOWN keys to set the desired temperature (80°F to 120°F) in one degree increments.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Changing the Temperature units (˚F/˚C) When the generator is Off, Press and hold ON/OFF key for 10 seconds. The temperature units will be displayed as Fahrenheit (TuF) or Celsius (TuC). Use the UP/DOWN keys to choose between (TuF) and (TuC). Press ON/OFF key to accept the new value and exit. aroma mr.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Display mr.steam Up Key Time Display/ Adjust Key ON/OFF Key temp time aroma chroma AromaSteam Key Time Display/ Adjust Key Down Key Program Key ChromaSteam Key Care Tips for all Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. Do not use abrasive cleansers 3.
mr.steam ® Feel Good Inc. Products, information and specifications are subject to change without notice. For more information call Sales & Support at: 1.800.76.STEAM (East Coast) 1.800.72.STEAM (West Coast) 2015 © Sussman-Automatic Corporation Mr.Steam and des., AromaFlo, AutoFlush, AutoSteam, Butler Package, ChromaSteam, Clean Steam...
Linear Steam Head ® mr.steam ® –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation Instructions Model 104216 READ ME FIRST! ! As you follow these instructions, you will notice warning and caution symbols. This information is important for the proper, safe and trouble free installation of the Linear Steam Head.
mr.steam Linear Steam Head® ® ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation Instructions: Model 104216 R E A D M E F I R S T ! (cont.) ! CAUTION • DO NOT use black iron pipe or galvanized pipe for the steam line. Use brass pipe or copper tubing only, and in accordance with national and local plumbing codes. • Do not modify or alter the steam head.
mr.steam Linear Steam Head® ® ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation Instructions: Model 104216 INSTALLATION STEPS STEAM EMISSION ! CAUTION Because steam emissions are very hot, locate the steam head where incidental contact by the bather with direct steam emission cannot occur.
mr.steam Linear Steam Head® ® ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation Instructions: Model 104216 STEP 5. Plumb rigid copper tubing or brass pipe from the steam generator to the steam head. Plumbing must not form traps or valleys. Thread sealant must be used as required to ensure a leak free joint. ! CAUTIONS • Plumbing must be installed by a qualified and licensed plumber.
I N S TA L L AT I O N I N S T R U C T I O N S Package Contents: SteamLinx Module and Mobile App allows for seamless control of time and temperature using your smart phone or mobile device. SteamLinx works with all MrSteam controls (for MS generators SN 1174000 and up). • SteamLinx A with Integral Cable • SteamLinx B and Ethernet Cable • Power Supply and Cable • Instructions These instructions contain safety alert symbols and panels.
2 Connecting SteamLinx B to the Home Router Home Router • Plug the blue ethernet cable provided, into an ethernet slot on the back of the home router. Power • Plug the power Supply supply into a 120V outlet. 3’ Cable Ethernet Cable (3’) 3 Connecting SteamLinx to the Internet 4 Troubleshooting: Blinking LED Troubleshooting: Indicator Lights Units are out of range or not paired LEDs • Insure the mobile device is on the WiFi network.
mr.steam ® Optional Autoflush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1/2" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Optional AutoFlush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Technical Specifications Condensation Pan 103867 & 104402 Mr.Steam strongly recommends the use of a condensation pan in the unlikely event of a plumbing leak. Locate the condensation pan on a solid level surface and place the steam generator inside the condensation pan. Insure the steam generator is level. All plumbing shall be performed by a qualified licensed plumber and in accordance with applicable national and local codes.
