Operation Manual
Congratulaons with the purchase of your mr Safe Baery/Accu Checker. The
Baery/Accu Checker represents the latest technology in baery tesng and
analyzing and will provide you quickly with accurate results using wireless
technology.
1. General advice and installaon notes
• Read the manual and safety notes carefully before installing the mr Safe Baery/
Accu Checker.
• If you have any doubts, contact your qualied auto/truck electrician or mechanic.
• WARNING: If the car baery is disconnected, it is possible that some management
systems will be disabled!
• Extra tools may be needed for the installaon.
• Check your vehicle manual for more informaon about the installaon.
• WARNING: Do not install on moving, sharp, hot or unsuitable surfaces!
2. General informaon
• The power source must provide 12/24 Volts DC and must be able to supply the
necessary current to operate the load. The power source may be a baery or a
well-regulated 12/24V DC power supply.
• CAUTION: The mr Safe Baery/Accu Checker must be connected only to baeries
with a nominal output voltage of 12/24V. The unit is designed to operate with
specic voltage baery. Please check and ensure the matching of the power input
before using the mr Safe Baery/Accu Checker.
• Please check whether the baery voltage meets the requirements specied on the
Baery/Accu Checker rang plate. Verify that the power source is at least fuse-
protected at 15A (12V) or 7.5A (24V).
• If these condions are met, please use the 12/24V cable provided to make the
connecon at the baery of the car/truck etc.
3. App
• Download the free mr Safe Baery/Accu Checker App from the Apple store (iOS
devices) or the Google Play Store (Android devices).
• When you are using the app for the rst me, you need to register with your mobile
phone number. You will receive a vericaon code, type this in and choose your
password.
• NOTE: The Wi-Fi funcon cannot be used with this device.
• Open the app and click “+ Add”. Scan the QR-code on the back of your mr Safe
Baery/Accu checker.
• The device is now added and can be read.
Please refer to the website www.mrsafe.eu for the full App manual.
4. Connecng
NOTE: make sure that
the vehicle engine and
any electrical loads
are “OFF”!
• Verify the ignion key is turned OFF and that no ammable fumes are present.
• Connect the red clamp to the posive (+) terminal and the black clamp to the
negave (-) terminal pole.
• The Baery/Accu Checker switches ON when both connecons are made.
• Ensure a good connecon by connecng the eyelets (m6 size 6mm /1/4” diameter)
around the terminals. The Baery/Accu Checker requires that both sides of each
clamp are properly connected before tesng can take place. When there is a poor
connecon, the status screen will display “no info”. If this happens, clean the
baery terminals and clamps and reconnect.
CAUTION: Reverse polarity will result in a blown fuse and may cause permanent
damage. Damage due to reverse polarity is not covered by our guarantee. Do not
use with posive ground electrical system (modern automobiles, RVs and trucks are
negave ground. Verify by checking your car manual).
5. Installaon
• Select the ideal mounng posion for the Baery/Accu Checker. Make sure that the
cables cannot get obstructed, or touching heat or are in the vicinity of sharp edges.
• Aach the Baery/Accu Checker with the cable es that are supplied.
• Make sure that the Baery/Accu Checker is mounted rmly and does not move or
vibrate.
• Check all the wires and make sure they cannot get loose or make connecon with
any heated parts.
6. Safety notes
• Do not operate the Baery/Accu Checker if the cord or plugs are damaged.
• Do not operate the Baery/Accu Checker if it has received a sharp blow, has been
dropped or damaged in any way.
• Do not disassemble the device. Incorrect reassembly may result in a risk of electrical
shock or re.
• NEVER smoke or allow a spark or ame in the vicinity of the device or the engine
of your car.
• Be extra cauous to reduce the risk of dropping a metal tool onto the baery. It
might spark, cause short-circuit on the baery or cause damage to an electrical part
that may cause an explosion.
• Remove personal metal items, such as rings, bracelets, necklaces, watches, … when
working near the baery. It can easily cause a short-circuit or heat the metal items
and cause burns.
• Determine the voltage of your baery by verifying the car manual and make sure
the output matches the output rang of the Baery/Accu Checker.
• For negave-grounded vehicles: connect the POSITIVE (red) clip from the Baery/
Accu Checker to POSITIVE (POS, P, +) ungrounded post of the car baery. Connect
the NEGATIVE (black) clip to the vehicle chassis or engine block. Connect the device
to a heavy gage metal part of the frame or engine block.
• Ensure that the cabling does not jam or comes in contact with hot surfaces or sharp
edges.
7. Support
For all quesons and addional informaon concerning this product, please contact
support@mrsafe.eu.
8. Guarantee
Copyright © mr Safe®. mr Safe® is a registered trademark of TE-Group NV. The mr Safe®
brand stands for superior quality products and excellent customer service. Therefore
mr Safe® warrants this product to be free from defects in materials and workmanship
for a period of two (2) years from the original purchase date of the product.
Mr Safe Baery/Accu Checker / 08-2017 / V01
USER MANUAL
BATTERY/ACCU CHECKER BAC-100
+
+
–
–
1
2
Gefeliciteerd met de aankoop van uw mr Safe Baery/Accu Checker. De Baery/
Accu Checker staat voor de laatste technologie in testen en analyseren van de
baerij en zal u snel voorzien met accurate resultaten via draadloze technologie.
1. Algemeen advies en noes bij de aeeldingen
• Lees de handleiding en veiligheidsvoorschrien zorgvuldig door vooraleer de mr Safe
Baery/Accu Checker te installeren. Bij twijfel kan u best een gecerceerde auto/truck
elektricien of monteur contacteren.
• WAARSCHUWING: wanneer de baerij ontkoppeld wordt, is het mogelijk dat sommige
beheerssystemen niet werken.
• Extra gereedschap kan nodig zijn voor deze installae.
• Kijk aljd de handleiding van uw voertuig na voor meer informae over de installae.
• WAARSCHUWING: Installeer het toestel niet op beweegbare, scherpe, warme of
ongeschikte oppervlakten.
2. Algemene informae
• De voedingsbron moet 12/24V DC zijn en moet de benodigde stroom kunnen leveren om
de lading te bedienen. De voedingsbron kan een baerij of een goed geregulariseerde
12/24V DC voeding zijn.
• OPGELET: De mr Safe Baery/Accu Checker kan enkel verbonden worden aan baerijen
met een nominale uitgangsstroom van 12/24V. Het toestel is ontwikkeld om te werken
met een speciek voltage. Gelieve zeker te stellen dat de stroomtoevoer overeenkomt
alvorens de mr Safe Baery/Accu Checker te gebruiken.
• Controleer of de spanning van de baerij overeenkomt met de vereisten gespecieerd op
het Baery/Accu Checker label. Zorg dat de voedingsbron een zekeringsbeveiliging van
15A (12V) of 7.5A (24V) hee.
• Als er aan deze voorwaarden voldaan wordt, kan u de meegeleverde 12/24V kabel
aansluiten aan de baerij van de wagen/truck etc.
3. App
• Download de gras mr Safe Baery/Accu Checker App van de Apple store (iOS toestellen)
of de Google Play Store (Android toestellen).
• Indien u de app voor de eerste keer gebruikt moet u registreren met uw telefoonnummer.
U zal een vericaecode ontvangen, typ deze in en kies uw wachtwoord.
• OPMERKING: De Wi-Fi funce wordt niet ondersteunt met dit type toestel.
• Open de app en klik op “+ Add”. Scan de QR-code op het label achteraan de mr Safe
Baery/Accu Checker.
• Het toestel wordt nu toegevoegd en kan uitgelezen worden.
Indien u meer informae wenst over het gebruik van de app, kan u de volledige handleiding
downloaden op www.mrsafe.eu.
4. Verbinden
OPMERKING: Zorg dat de
motor uitstaat en dat er
geen elektrische ladingen
zijn.
• Controleer dat het contact van het voertuig uitstaat en dat er geen ontvlambare gassen
aanwezig zijn.
• Verbind de rode klem met de posieve (+) pool en de zwarte klem met de negaeve (-)
pool. De Baery/Accu Checker zal aanspringen wanneer beide verbindingen gemaakt zijn.
• Zorg voor een goede verbinding door de oogjes (m6 grooe 6mm/1/4” diameter)
rond de polen. De Baery/Accu Checker vereist dat beide kanten van de klemmen
goed aangesloten zijn alvorens er een test kan uitgevoerd worden. In geval van slechte
verbinding, zal het scherm “no info” weergeven. Indien dit gebeurt, maak dan de
baerijpolen en klemmen schoon en verbind opnieuw.
OPGELET: Omgekeerde polariteit zal resulteren in een doorgebrande zekering en kan
blijvende schade veroorzaken. Schade door omgekeerde polariteit valt niet onder de garane.
Gebruik niet met een posief geaard elektrisch systeem (moderne auto’s, vrachtwagens,…
zijn negaef geaard. Om dit te controleren: controleer de handleiding van uw voertuig).
5. Installae
• Selecteer de ideale bevesgingsposie voor de Baery/Accu Checker. Zorg dat er niets de
kabels kan belemmeren, dat ze geen hie aanraken of in de buurt van scherpe kanten liggen.
• Maak de Baery/Accu Checker vast met de meegeleverde kabelbinders.
• Zorg dat de Baery/Accu Checker stevig vasthangt en dat hij niet beweegt of kan vibreren.
• Controleer alle draden en zorg dat ze niet los kunnen komen of verhie onderdelen
kunnen aanraken.
6. Veiligheidsvoorschrien
• Gebruik de Baery/Accu Checker niet indien de kabels of oogjes beschadigd zijn.
• Gebruik de Baery/Accu Checker niet indien hij een klap gekregen hee, gevallen is of
beschadigd is.
• Ontmantel het toestel niet. Onjuiste ontmanteling gee risico tot elektrische schok of brand.
• Zorg dat er NOOIT een open vlam of ontsteking in de buurt van het toestel of de motor
komt.
• Wees extra voorzichg om het risico te verkleinen dat metalen gereedschap op de baerij
valt. Dit kan voor een ontsteking zorgen, kortsluing van de baerij of schade aan een
elektrisch onderdeel. Dit kan leiden tot een explosie.
• Verwijder persoonlijke voorwerpen zoals ringen, armbanden, halskengen, horloges,…
wanneer u in de nabijheid van de baerij werkt. Dit kan makkelijk kortsluing veroorzaken
of het metaal zo verhien dat het brandwonden veroorzaakt.
• Bepaal de spanning van uw baerij door de handleiding van uw voertuig te lezen en zorg
dat de uitvoerstroom de vereisten van de Baery/Accu Checker tegemoetkomt.
• Voor negaef-geaarde voertuigen: verbind de POSITIEF (rode) klem van de Baery/
Accu Checker met de POSITIVE (POS, P, +) ongegronde post van de autobaerij. Sluit
de NEGATIVE (zwarte) clip aan op het chassis of motorblok van het voertuig. Sluit het
apparaat aan op een zwaar metalen onderdeel van het frame of motorblok.
• Zorg ervoor dat de bekabeling niet vastloopt of in contact komt met hete oppervlakken
of scherpe randen.
7. Support
Voor meer informae, technische vragen of retouraanvragen met betrekking tot dit product
dient u rechtstreeks contact op te nemen met support@mrsafe.eu.
8. Garane
Copyright © mr Safe®. mr Safe® is een gedeponeerd handelsmerk van TE-Group NV. Het merk
mr Safe® staat voor producten van superieure kwaliteit en een uitstekende klantenservice.
Daarom garandeert mr Safe® dat dit product vrij is van materiaal- en fabricagefouten
gedurende een periode van twee (2) jaar na de oorspronkelijke aankoopdatum van het
product.
+
+
–
–
1
2
DECLARATION OF CONFORMITY
Hereby, Par la présente,
Company /Entreprise:
Address: / Adresse:
declare that the following equipment: / déclare que le disposif suivant :
Product name:
Nom du produit:
Product type:
Type de produit:
conforms with the following safety requirements of the direcves 2014/53/EU & 2011/65/EU.
Conformity is guaranteed by the CE-symbol. This product has been tested against following standards
and specicaons, applying versions valid in August 2017. The full text of the EU declaraon of
conformity is available at the following internet address: www.mrsafe.eu.
est conforme aux exigences de sécurité suivantes des direcves 2014/53/EU & 2011/65/EU. La conformité
est garane par le symbole CE. Ce produit a été testé par rapport aux normes et spécicaons suivantes,
appliquant les versions valides en Août 2017. Le texte complet de la déclaraon UE de conformité est
disponible à l’adresse internet suivante: www.mrsafe.eu.
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
Dra EN 301489-1 V2.2.0
Dra EN 301489-17 V3.2.0
EN 300328 V2.1.1
S. Izaks, Product & Research Manager TE-Group NV
Kapellen, August 2017
Authorized Signature
TE-Group NV
Kapelsestraat 61, 2950 Kapellen, Belgium
mr Safe BAC-100
Baery/Accu Checker