User Manual MR. C@FFEEs Coffeemaker Models UR12, UR13. URX20. URX23.
IMPORTANT SAFEGUARDS. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: l l l l l l l l l Read all instructions before using the coffeemaker. Do not touch the coffeemaker’s hot surfaces. To protect against electric shock, do not immerse the power cord, power plug, or coffeemaker in water or other liquid.
Special cord set instructions 1. A short power supply cord is provided to reduce the hazards resulting from becoming entangled in or tripping over a longer cord. 2. An extension cord may be purchased and used if care is exercised in its use. 3.
Table of Contents . Setting up your coffeemaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Coffeemaker features . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... .. .1 Adjusting the power cord length .. .................... Setting the clock (models URXPO, URX23, URX30 . . . . . . . . . .3 and URX33 only) . . . . . . . . . .3 . Brewing coffee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up your coffeemaker Congratulations on your new MR. COFFEE” coffeemaker! Please read these instructions carefully before using your new coffeemaker. Proper use, care and maintenance will ensure trouble-free operation and the long life of this appliance. Save these instructions for cleaning and, if necessary, replacement parts information. Coffeemaker features Your new MR.
Models URl2 and URl3 1. Control panel a. OFF switch b. ON switch and indicator 0 1 models URl2 and UR13 @ models URX20 and URX23 Models URX20 and URX23 2A. Control panel a. PRESS HOLD button b. MIN. (minute) button c. Delay Brew indicator d. PM indicator e. On-Off indicator f. BREW NOW button 2. Clock display h. DELAY BREW button i. HOUR button @ models URX30 and URX33 Models URX30 and URX33 28. Control panel a. PRESS HOLD button b. Hour button c. Min. (minute) button d.
Adjusting the power cord length You can customize the length of the power cord up to 3 feet so that it is the exact length you desire. To increase the length of the power cord: Grasp the power cord (not the power plug) and gently pull it away from the coffeemaker. To decrease the length of the power cord: Grasp the power cord a few inches away from where it attaches to the coffeemaker. Slowly feed it into the coffeemaker.
Brewing coffee Cleaning the coffeemaker before first use Follow the steps under “Adding water and ground coffee” and “Brewing coffee now,” (pages 5-6) but do not add coffee grounds. Selecting and measuring ground coffee For best results, use coffee ground for use with automatic drip coffee makers, The amounts shown below are suggested amounts. To brew...
51 Remove the water reservoir by gasping the hand holds in the back of the reservoir, and pulling up. Fill it with the desired amount of tap water. Replace the reservoir on the coffeemaker, making sure that it is firmly attached to the coffeemaker body Make sure the reservoir is squarely centered A on the coffeemaker or the water may overflow. An overflow may cause personal injury or damage to property.
For models URX20, URX23, URX30 and URX33: 1 ) If you are making four cups of coffee or fewer, press the 1-4 Cups button (models URX30 and URX33 only). 2.) \ 0 . <.) 6:35 Press the BREW NOW button The ONeOFF indicator will light, indicating that the coffeemaker is on and the brew cycle will begin When the coffee stops flowing, the brew cycle is complete. You will hear 5 beep tones (models URX30 and URX33 only). To turn off the coffeemaker, press the BREW NOW button.
3.) While still pressing and holding the PRESS HOLD button, press and hold the Min. button until the clock displays the correct minute. 4.) , Release the PRESS HOLD button. 5 ) Press the DELAY BREW button. The Delay Brew indicator will light. The delay timer is set and the coffeemaker will begin brewing the coffee at the time you selected.
Maintaining your coffeemaker Maintaining your coffeemaker and its parts will help extend the life of the appliance. MR. C@FFEEa Cleaning the coffeemaker Your coffeemaker must be cleaned when You notice any of the follow conditions: l excessive steaming l increased brew cycle times the pumping action stops before all of the water has been pumped from the water reservoir These conditions are caused by lime or other mineral deposits.
b. When three cups of vinegar have flowed into the decanter, turn the coffeemaker off and let the vinegar stand for 30 minutes. c. Turn the coffeemaker back on and let all the vinegar flow through. d. When the brew cycle is complete, turn the coffeemaker off and discard both the vinegar and the paper filter. For Models: l URX30 and URX33 a. Press the Clean Cycle button. The Clean Cycle indicator will light.
6.) Place the decanter on the warming plate and turn the coffeemaker on and allow it to complete a brew cycle. 7) Discard the water in the decanter and turn the coffeemaker off. Repeat steps 5 through 7 to flush all traces of vinegar from the coffeemaker. Cleaning the decanter Hard water can leave a whitish stain on the decanter. Coffee and tea may then turn the stain brown.
Service and maintenance Replacement parts . Filters For better tasting coffee and tea, we recommend that you use MR. COFFEE” brand 8-12 cup paper filters or MR. COFFEE” brand permanent filters. These filters are available at most grocery stores. . Decanters You can usually purchase a replacement decanter from the store where you purchased your coffeemaker. If you are unable to find a replacement, please call I-800 MR COFFEE (l-800-672-6333) in the U.S.
One-year limited warranty Sunbeam Products, Inc. (‘Sunbeam”) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component.
