Mr.
Step 1 : Check the contents of your box H F A B C D E G Before starting assembly, be sure to check all contents and lay out the various tree parts accordingly. There are: A. Top tree section. B. Middle tree section. C. Bottom tree section. D. Control box and power cord with adaptor. E. Tree stand. F. Three pins for the tree stand. G. “Ornament” with voice activated command list. H. Spare bulbs: 14 pieces (in the polybag attached to the end of the light strand inside the tree).
Step 2 : Expand Stand Figure A Figure B Figure C 1. Take the tree stand and pull apart the legs (Figure A), open to full Position (Figure B) 2. Take the fully opened tree stand and insert pins into the pre-drilled holes, tightening the pins part way (complete tightening in Step 3-1).
Step 3-1 : Tree Assembly 1. Take the tree section labeled “C” and insert into the top of tree stand. (Figure A) 2. Fully tighten the 3 pins into place (Figure B). Secure the tree base firmly to the tree stand.
Step 3-2 : Tree Assembly Take Tree Section labeled “B” and insert into the top of the pole of section “C”.
Step 3-3 : Tree Assembly Take the tree section labeled “A” and insert into the pole into the top of the pole of section “B”. Section A Section B Section C 6 IMPORTANT TREE SET UP TIPS: 1. Shake the tree well after assembly to ensure the branches are extended. 2. Some shaping of the tree may be required for best appearance. 3. Spare bulbs are included in a small bag inside the tree. Remove from the tree and keep in case replacement is needed.
Step 4 : Connect to AC Power Attach the power cord with adaptor to the control box, plug the adaptor into an AC power source.
Step 5: Connect to Alexa 1. Download the “Amazon Alexa” application from the app store on your mobile device . 2. Install and open the “Amazon Alexa” application. 3. Go to the settings menu. 4. Select “Add Device” 5. Select “Christmas Tree” and follow the on-screen instructions. 6. To set up a second tree, select “Second Christmas Tree” and follow the on-screen instructions. Alexa will ask for clarification if a command does not target a specific tree.
Step 6-A: Change your Christmas Tree LED lighting Mode using Alexa Color options Command – “Set Christmas tree to” : 1. Red 2. Green 3. Yellow 4. Blue 5. Purple 6. Light Blue 7. White 8. Multi-Color Follow the voice commands for a list of functions to achieve up to 40 lighting functions. Figure A Lighting functions Command – “Set Christmas tree to” : a. STEADY b. SPARKLE c. FIREFLY d. FLIP e. FADE Refer page 12-14 for examples of commands.
Step 6-B : Manually change your Christmas Tree LED lighting mode Push Button on Control Box to switch Christmas Tree LED Light Mode. There are a total of 40 lighting modes: Demo Mode is available: Press and hold the button on the control box of the tree for 3-4 seconds. The tree lights will turn green and will flash 3 times This indicates that the instructions were received. The Demo mode will start and play all 40 lighting functions. 1. White Steady 2. Red Steady 3. Green Steady 4. Blue Steady 5.
Step 6-C : Automate your Christmas Tree with Routines Alexa Routines allow you to automate your Christmas Tree Functionality. With Routines, you can turn your tree on with custom commands (i.e. Good Morning) or turn the tree on/off at scheduled times (i.e. every day at 10AM) How to Enable Routines with Alexa. 1. Open the Alexa app. 2. Go to the menu and select “Routines” 3. Select Plus 4. Select “When this happens”, and then choose how to begin your Routine (i.e. “Good Morning, or a scheduled time). 5.
Example 1 ： Turn Christmas Tree on “Turn Christmas Tree ON” Example 2 ： Set lighting mode to red “Set Christmas Tree to : Red” 12
Example 3 ： Set lighting mode to Fade “Set Christmas Tree to : Fade” Example 4 ： Turn Christmas Tree off “Turn Christmas Tree OFF” 13
Example 5 ： Turn Christmas Tree on with Routine “Good Morning / Good Night” 14
Connectivity Troubleshooting Common connectivity troubleshooting steps. 1. I can't connect my device to Alexa. • Reset your tree • To reset your Alexa Tree: press and hold the button on the control box for 10 seconds. Indication of action done: 3 flashes of white light. Then follow the instructions below. a) Download the "Amazon Alexa" application from the app store on your mobile device. b) Install and open the "Amazon Alexa" application. c) Go to the settings menu.
Connectivity Troubleshooting Common connectivity troubleshooting steps. 2. I can't get my Christmas Tree barcode to scan successfully. • Make sure that there is enough light in the area for the bar code to be detected. • If that does not work, then during the Alexa mobile app setup process, select "Don't Have a Barcode" and follow the on-screen instructions. 3. My Christmas Tree stopped working with Alexa. • Try a power cycle: Unplug your Christmas Tree from the outlet, and then plug it back in.
Connectivity Troubleshooting Common connectivity troubleshooting steps. 4. I can only turn my Christmas Tree On and Off with Alexa. • Although the Alexa tree can be added to a group, the color and function selections will not work using the group name. • Color and Function can only be selected by using the utterance "Christmas Tree." 5.
IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the Following: a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided contact a qualified for proper installation.
