Installation Guide
1. Remove front cover
of Spotlight by rotating
counter-clockwise as
shown above. Pull face
out from cup to reveal
battery holder.
2. Push down on
battery door tab to
release. Insert 3 D-Cell
batteries into Spotlight.
Attach battery door by
matching the tabs to the
rectangular holes and
then push down on front
until door clicks into
place.
3. Match arrows then
turn clockwise. Make
sure unit is securely
closed with arrow
pointing at the lock
symbol to ensure
weather proof seal is
tight.
4. Determine location
for mounting Spotlight.
NOTE: For best
performance, spotlight
should be positioned so
motion sensor is on top
and light is on bottom.
5. Remove mounting
base by turning
thumb screw counter-
clockwise.
6. Pull mounting base
o stem.
7. Drive three screws into
the three holes located
on mounting base.
8. Insert spotlight stem
back into mounting
base pointed in desired
direction and tighten
thumb screw in base.
9. Loosen larger thumb
screw that connects
Spotlight head to
mounting base and
adjust Spotlight head
to proper direction as
shown above. Tighten
thumb screw.
Spotlight features:
Fully Adjustable: Light can be rotated
360° as well as up and down
Light Coverage: up to 400 sq ft
Durable, Weather Resistant: Tight seals
and UV resistant material allow the light
to work in all weather conditions
Remote Control: Control from up to
70 ft away
What you need to install:
• 1 Small Screwdriver
• 3 D-Cell Alkaline Batteries
What is included per light:
• 1 Remote Controlled Spotlight
• Mounting Base
• 3 Screws & 3 Anchors
• 1 Remote Control with Mounting
Bracket + 2 screws
• (1) 3V Coin Battery
Installation Instructions
Remote Controlled Spotlight
MB370 / MB371
LED Light
Mounting Base
Thumb Screw
Knuckle Screw
Motion &
Light Sensor
Dim
Bright
Auto
Shut-o
Motion
Control
Indicator
Light
Syncing your light
Customize Remote
www.mrbeams.com
Tips:
•
Use only new alkaline D-Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batteries are not new, it may cause light to malfunction.
•
Install batteries with polarity in correct position.
* 1 year limited warranty. Visit site for details.
* Visit our website to view installation video.
Battery Caution:
1) Do not mix old and new batteries
2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium or Nickel Metal Hy-
dride) batteries
3) Do not dispose of batteries in re
4)Batteries should be recycled or disposed of as per state and local guidelines
1. The remote is paired to work only with
the Spotlight it is packaged with. To sync
additional spotlights to a single remote,
press the exposed black button on the
spotlight next to the battery compartment
for 3 seconds while pressing the ON button
on the remote.
1. Open the Remote Control with a small coin
and insert one at 3V battery (included) as
shown on the inside of the Remote Control.
Smooth side of battery should be facing up.
2. Determine
placement for bracket
for remote and attach to
wall using two screws
(included) or tape.
3. Slide Remote
into bracket as
shown above.
A Turns on Remote/ Adjust Auto Shut-o
B Turns o Remote
C Increase Brightness
D Decrease Brightness
E Turn Motion Sensor On/O
Activation: Spotlight can be turned on or o with the remote control.
Activating the remote will override the light sensor, and light can be activated
at any time. Default auto shut-o mode is set for 30 seconds.
2 Auto Shut-o Options: First, activate light with remote. Next, hold the ON
button down until light blinks. When it blinks 1x, auto shut-o is set to 1 hour.
When it blinks 2x it is set for 4 hours.
3 Brightness Modes: First, activate the light with the remote control. Next,
press the bright or dim button to adjust brightness. Brightness options are 60,
90, and 140 lumens.
Motion Sensor Activation: Spotlight will activate when motion is sensed from
up to 30 ft away. Motion sensor only activates in darkness to conserve energy.
Disable Motion: Activate light with remote. Click the motion sensor button
down until light blinks. When it blinks 2x the motion sensor has been disabled.
When it blinks 4x, the motion sensor has been enabled. Light will remember
your last motion setting.
Remote Set-up
Using the Remote
Set up
600 Beta Drive, Mayeld Village, Unit 100, Mayeld, OH 44143
877.298.9082