ICR-350 User Manual
IMPORTANTSAFETY INSTRUCTIONS PRECAUTIONS To maintain optimum performance: Do not use unit in places which are extremely hot,cold,dusty or humid. Do not use or keep the unit in following places. In a high humidity. In an area exposed to direct sunlight. Near sources of strong magnetism,such as televisions,speakers or magnets. Where there is a lot of movement or vibration, such as on a car . For safety Do not attempt to disassemble this unit.
If you hear no sound, DO NOT turn the volume up high because the music could suddenly begin at high volume. To avoid hurting your ears or damaging the headphones turn the volume control to the lowest level before starting playback and slowly turn it up to the desired level. Designs and Specifications are subject to change without notice.
Location of Controls: 1. Line-in socket 2. Earphone socket 3. Built-in microphone 4. Status indicator 5. LCD display 6. HOLD button 7. USB jack 8. Record 9. Stop/Pause 10. Power on/off/playback/pause 11. Menu/ Previous/REW /Next/FF 12. Volume +/ Volume 13. Louder speaker 14. Lock button 15.
Display · Battery Level · The name of playing songs, number and time · Repeat Mode 7 modes: Normal, Repeat One, Folder, Repeat Folder, Repeat All, Random, Intro · EQ mode 7 modes: Natural, Rock, Pop, Classical, Soft, Jazz, DBB 4
Basic operation 1. Power supply It is powered by AAA battery or USB. When the remaining capacity of battery indication shows , please change the battery in time. 2. Power on/off A. Press and hold button to power on. The LCD displays the startup logo. B. Under the playback or stop (pause) status, press and hold to power off. Note: If the unit is locked by the HOLD key, it displays the locked icon and then power off automatically while power on. 3.
1. Enter from the menu 1). Turn on the unit and enter the main menu. 2). Select the Recording mode REC by / button, and then press the M button to confirm and enter. 3). Press button to begin to record. 4). Press and hold ■ button or the M button to stop recording and save at the same time. Note: (1). If the LCD displays “Disk Full”, it means that there is no enough space in the disk, please delete some files to release the space. (2). The unit supports 99 files under every directory.
3. Select Record type 1) Under the recoding stops interface, press M button to enter the record menu. 2) Select “record type” and then press the M button to enter. Then select “record type” option by or button and then press M to confirm. REC Type: SP record, WAV format, good timbre LP record, ACT format, general timbre SP VOR, WAV format, voice-control REC LP VOR, ACT format, voice-control REC Voice-control indicates that the record is controlled by voice.
Telep h o n e l in e 4. Telephone conversation recording Connect the external telephone line and telephone cable to the telephone adaptor; link the audio line to the adaptor and LINE IN jack. Continuously press ● button to start recording. LI NE I N LINE IN cable Telephone line Telephone adapter 5.
before your recording in order to avoid failed recording) Note: during the recording, if the unit was shut off by knock or other actions, all recording files will lost. So please operate carefully. 6. Convert ACT format files into WAV format 1). After install the software, open and run “sound converter”, click “open” 2). Select the ACT files you want to convert 3).
III. Music Mode MSC and Voice Mode VOI 1.
short press decrease volume step by step long press decrease volume continually ﹣ ● ■ decrease volume step by step decrease volume continually Enter the record Enter the A-B short press interface and start repeat status to record Enter the record Enter the A-B long press interface and start repeat status to record × short press To pause recording Enter the playing long press To save recording submenu × × × × × × × × × × Enter the record start to record interface and start to record Enter th
options: Main directory, Delete one, Delete All, and exit. Select the corresponding option by or button. 1). The unit support 99 top-level subdirectories. You can save different files in different directories (the directory should be pre-built in the PC), so that you can play and manage them by classifying. Note: I. You can set the “Main disk directory” for music mod, record mode and voice mode respectively, i.e., the “main disk directory” of these three mode do not correspond the same directory. II.
Note: “delete all” can only delete the files in the current directory under the current mode. For example, under the music mode, if you select “delete all”, you can only delete the music files. The recorded files will not be deleted.) 3). Select “exit”, press the M button to exit the stop menu. 3.
Random and Intro. Normal: After the music in the current directory have been played fully, the player will play the music in the next directory till all files are played and then it will stop. Repeat One: Repeat playing a single piece of music. Folder: Play all the music in the folder. Repeat Folder: Repeatedly play all the music in the folder. Repeat All: Repeatedly play all the music. Random: Play randomly the music in the current folder.
(Natural) (Rock) (Pop) (Classical) (Soft) (Jazz) (DBB) 3). Tempo Rate When playing the music files (only applicable for MP3 files) and recorded files, the user can select different tempo rate (slower or faster), but the sound will not be changed. 4).
(1) While playing, press ●button to set the point “A”, the letter “B” in the repeat icon will flash. Press the ● button again to confirm the starting point B. Then the player will repeat playing between A and B. When reaching the set times or short press the M key to exit Repeat mode. (2) Follow function (the voice mode doesn't have this function) In A-B repeat, press ● button to enter the follow mode, the repeat icon “ ” is changed into the follow icon “ ”.
press M button to exit. (4)Replay Times (only music mode has this function) Press M button to adjust the repeat times, the repeat times will determine it will exit after how many times of A-B repeat it plays. (5) Replay gap (only music mode has this function) Press M button to adjust the replay gap, the replay gap will determine the time length to be paused between this playing and the last playing (unit: second) (6)Exit Press the M key shortly to exit the play menu. 4.
V. Lock Under the playback or stop mode, status, push HOLD key per arrowhead direction to lock the player. On the hold mode, non of the functions can be used. VI. System setup SYS 1. Clock 1). The current time (Electronic watch function.
Press + (- to the reverse direction) to start to set form year (the year option start to blink), then increase or decrease the numeral by or button. Then shortly press + to select Month, Day, Hour, Minute and Second and also increase or decrease the numeral by or button. Press M or key to confirm and exit after adjustment. 2). Pre-record Set a time, and the unit will start to record automatically at the pre-set time. Press the M button to enter the Pre-record interface.
The way to adjust the pre-set time is same as the above: set the Year, Month, Day, Hour, Minute and Second one by one, and then press M or key to confirm and exit after adjustment. Note: press ● button to turn on/shut down the function of pre-REC. if you shut down this function, there is no bell icon on the display. 3).
Minute and Second one by one, and then press M or after adjustment. 2. Backlight time key to confirm and exit Press the M key to enter the backlight time interface. / button to adjust the backlight. The unit of time is second. Press Press the M or key to confirm and exit after setting. 3.
Press the / button to select the corresponding language and the shortly press M button to confirm and exit. 4 Power off setting Press the M button to enter the power off setting interface. There are two modes: 1). Power-saving mode Set the time of Power off (unit: minute), in Stop state, the time is calculated when no key is pressed and the player would power off automatically. If it is set as 0 second, the function will be inactivated. 2).
powered off. (i.e. set for one time) it is mainly used for listening to songs before your sleep. The setting will be canceled automatically after power off. You have to reset it if you want to use it again. 5. Repeat Setting Press the M button to enter the repeat setting interface. There are two modes: 1). Manual Mode means it can not pause automatically when A-B repeat, but to set the point manually. 2). Auto Mode means it can pause automatically. (Pertaining to recitations without music.) 6.
8. Memory info: Check the remaining capacity of the flash memory. The former numerals represent the total capacity of the disk, and the percentage represents the percentage of the used space. 9. Firmware version: Display the version of firmware. 10. Firmware upgrading VI. Connection with PC Install the driver for Windows Operating Systems 98 SE. For windows Operating System ME/2000/XP or greater, you don’t need to install the driver. Turn on the player and insert USB into the USB ports of your PC.
Create a File Folder: This player can recognize 99 files of level one created in portable disk by user. 2. Upgrade Player The player may be upgraded or maintained its system firmware using the tools and software installed on the computer. 1. Enter the main menu, press “ / ” key to select “System Setting”.
press “M” key to enter and press “ / ” key to select "Firmware Upgrade”， press M key again to confirm and enter. 2. Connect the player to PC. 3. Run the upgrading tool “MP3PlayerUpgrade” of PC, and then click “Select the Firmware file of new version” knob. Select the new firmware program (it can be found in the disk enclosed with the player or downloaded from the producer's website). 4. Click the “Start upgrading” button and the system will start the work of upgrading. 5.
Note: 1. Firmware upgrading is used for enhancing and optimizing the performance of the player. But if the firmware is not upgraded, the normal work of the player will not be affected. 2. The errors caused from the firmware upgrading may result in the failure of the player! So please read the operation manual carefully before the operation. It is recommended that this operation shall be done by the persons with sufficient computer knowledge. 3.
3. Function of Special Space The user can arbitrarily divide the USB disk into two parts through the tools enclosed with the player, (the use can see two disk letters. For system of Windows 2K, the computer should be installed with the SP4. Otherwise, the user can only see one disk letter. If the user wants to see the other disk letter, he has to select the “Single common disk” or “Single encryption disk” under “System setting/ On-line mode”.
Then click the related block to set the user' name and the passwords. Enter the name in the block of “New user's name” and enter the password in the block of “New password”. Then enter the new password again in the block of “Confirm the new password”. Click the button “Start” to start dividing the disk. 4. After dividing, the user will see the Left Indications: 5. Press “Enter”, and the computer will indicating for restart the system. Confirm it so as to restart the computer system.
6. After starting, the user will see two disks (for the operation system lower than Windows 2K SP4, the user can only see one disk letter). Click the encrypted disk (listed at the second place), which has three files. Two are hidden files and one is the execution file. The disk only has the space of 300K. 7. Run the execution file “RdiskDecrypt.exe” and enter the user's name and password into the Dialogue box. If the password is correct the Copy file in the disk will be opened.
8.Each time when connecting with the computer, user must enter the user's name and password so that he can open the encrypted disk. Note: these files in the encrypted disk can't be identified by the player. Note: Either when the disk is divided into two parts or when two disks are combined into one, the data in the disk will be Deleted, please backup the data in advance. Warning: Please don't lose your User's name and password; otherwise the encrypted disk cannot be used.
1.Why can’t some MP3 be played? Standard MP3 only includes: the songs in layer 3 of MPEG 1, layer 3 of MPEG 2 and layer 3 of MPEG 2.5. Otherwise, it won’t be played in the player except transformed by the corresponding software. 2.Why doesn’t the memory size displayed under the operational system match the figure on the tab? The software in the MP3 player takes up a small portion of the memory, which coincides with the corresponding standards. 3.
4.What causes the MP3 player running slowly? Using or deleting files frequently in a long time will generate fragments in the flash memory, like fragment in the hard disk, which will cause the player running slowly. 5.What if the driving program of the MP3 player be damaged? This is caused by improper operation. For details, please refer to the Upgrade/Renew Software part. 6.What if the MP3 play works abnormally, i.
Specification Flash memory: 1GB. Max recording time: HQ: 64Hr/LQ:16,000min PC Supports ; Windows 98/ME/2000/XP, Mac OS 10.X & Linux kerne 1.2.4.2 & above Dimension: 100mmx34mmx14mm Weight: 24g (35g included battery) Power source: AAA battery Microphone: built-in capacitor microphone Input: Built-in MIC Output: Double-channel earphone, above 8 ohm.
