HERA51 Mobile POS AndroidTM 8.1, OreoTM Version 1.
HERA51 Mobile POS - 2-
Important Notices IMPORTANT NOTICES FOR USA FCC ID: 2ASPU-HERA51 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
HERA51 Mobile POS FOR PRODUCT WITH LASER This laser component emits FDA / IEC Class 2 laser light at the exit port. Do NOT STARE INTO BEAM DIRECTLY. Do not aim the beam at the eyes. Any adjustments or performance excluding those specified herein may result in hazardous laser light exposure. ENVIRONMENT Operate the mobile POS at ambient temperatures from 0°C to 50°C and with humidity range from 5% to 95%.
Important Notices SAFETY PRECAUTIONS For people’s safety Do not listen at high volume levels for long periods to prevent possible hearing damage. Do not operate this device while walking, cycling or car driving. For the equipment Do not use any batteries or charging devices which are not originally sold or manufactured by MPLUS TECHNOLOGY CO., LTD. Do not replace the battery with an incorrect type, to avoid the risk of heat generation, fire, or explosion.
HERA51 Mobile POS BATTERY Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. The main battery may not be charged to full for shipment. Charge the main battery to full before using the mobile POS for the first time. Main battery: The main battery powers the mobile POS to work. It takes approximately 4 hours to charge an empty main battery to full.
Important Notices CONNECTION Via Bluetooth or WLAN Connection may fail when the mobile POS is around other wireless machines or power cables as the radio frequencies of those may cause interferences. If communication fails, move the devices much closer to each other, and try to communicate again After turning on, Bluetooth power is sustained even when the mobile POS is suspended. However, if the power mode is switched to Airplane Mode, Bluetooth power will be turned off regardless of the settings.
HERA51 Mobile POS E-LABEL - 8-
Release Notes RELEASE NOTES Version Date 1.
CONTENTS IMPORTANT NOTICES.....................................................................................................................- 3 For USA .......................................................................................................................................... - 3 For Product with Laser .................................................................................................................. - 4 Environment ............................................................
2.2.2. 2.3. 2.3.1. 2.3.2. 2.3.3. 2.3.4. 2.4. 2.4.1. 2.4.2. 2.4.3. 2.5. 2.6. 2.6.1. 2.6.2. 2.7. 2.8. 2.9. 2.9.1. 2.9.2. Manage Storage Space .........................................................46 Touch Screen ...................................................................... 54 Screen Brightness ................................................................. 54 Screen rotation .................................................................... 55 Screen Timeout Settings .........................
4.2.7. 4.2.8. 4.3. 4.3.1. 4.3.2. 4.3.3. 4.3.4. 4.3.5. 4.4. 4.4.1. 4.4.2. 4.4.3. Modify Wi-Fi Network ............................................................ 141 Disconnect Wi-Fi Network....................................................... 141 Use Bluetooth..................................................................... 142 Bluetooth Profiles ................................................................ 142 Turn On Bluetooth ...............................................................
HERA51 Mobile POS INTRODUCTION The HERA51 mobile POS, powered by Android 8.1 Oreo, is light-weight, easy to use, providing powerful and handy tools for the purpose of delivering flexibility in customization. Specifically designed to work as an industrial PDA, it provides rich options of data collection, voice and data communication, long-lasting working hours, and so on. Its large color capacitive display guarantees ease in reading in all lighting conditions. Integrated with Bluetooth 2.1EDR/4.0 BLE/V4.
Introduction FEATURES Android 8.1 Oreo operating system with a powerful Cortex 1.3 GHz Quad-Core processor 16GB eMMC flash memory to store OS and software programs 2GB LPDDR3 SDRAM to store and run programs, as well as store program data One expansion slot for microSDHC card up to 32GB and microSDXC card up to 64GB. Built-in 13 Megapixel rear camera with white LED for flash and auto focus. One side trigger for scanning Total wireless solution — connectivity includes Bluetooth 2.
HERA51 Mobile POS Chapter 1 QUICK START This chapter helps you get ready for starting using the mobile POS. IN THIS CHAPTER 1.1 Overview ................................................................... 17 1.2 Charging & Communication ..........................................
Quick Start 1.1. OVERVIEW No. Description No.
HERA51 Mobile POS 1.1.1. INSTALLING/ REMOVING BATTERY For shipping and storage purposes, the mobile POS and the main battery are saved in separate packages. Note: Any improper handling may reduce the battery life. INSTALL MAIN BATTERY To install the main battery, please: 1) Insert the main battery with the contact pins facing the lower end. Fix the lower edge of the battery first. 2) Then push down the upper end. The battery latch will fit into place with a click sound.
Quick Start IMPORTANT CHARGING INFORMATION Power Adaptor Battery Pack Charging time Input: AC 100-240V, 50-60Hz; output: 5V/2A CipherLab approved 3.8V 4000mAh rechargeable Li-ion CipherLab proprietary Approx. 4 hours via adapter at 25°C For the first time charging the main battery, please charge it for at least 8 to 12 hours. Note: For initial use, insert a charged battery, and then press the Power key to power on the mobile POS. REMOVE BATTERY 1) 2) 3) Shut down this device first.
HERA51 Mobile POS 1.1.2. INSTALLING SIM CARD, SAM CARD AND MEMORY CARD The HERA51 mobile POS is equipped with one SIM card slot, two SAM card slot and one memory card slot. To insert the cards: 1) Remove the battery as described in Remove Battery. 2) Insert your fingernail into the notch above the inner lid that protects the card sockets chamber, and lift it up.
Quick Start 3) After the chamber is revealed, insert SIM cards, the SAM card and the microSD card into their respective sockets. Close and push back the hinged cover till a click sounds. To Install the Cards: Swing the top to open. Insert the cards, close the it back. 4) Replace the inner lid. 5) Replace the battery. Note: Refer to SIM Card Management for details on managing SIM card. 1) Remove the battery. 2) Remove the inner lid. 3) Unlock the card hinge cover and remove the card.
HERA51 Mobile POS 1.1.3. POWER ON/OFF MOBILE POS POWER ON To power on the mobile POS, press and hold the power button located on the upper right side of the device. The mobile POS will turn on and show the Home Screen after splash screen. Note: For the mobile POS to power on, the battery cover must be secured in place. POWER OFF To power off the mobile POS, press and hold the power button for more than three seconds. A menu will appear on-screen which allows you to power off the device.
Quick Start 1.1.4. HOMESCREEN SELECTION Upon the first time you launch the system, a Select Home app window will pop up to request your immediate choice of home screen. By selecting “AppLock”, you will directly enter AppLock application (please refer to AppLock User Guide for detailed instructions on AppLock settings) to start configuring the interface provided to normal users of this device; by selecting “Launcher”, you will enter the default Android 8.1 home screen.
HERA51 Mobile POS 1.1.5. USING HARDWARE BUTTONS On the bottom of the mobile POS are three hardware buttons that deliver the following functions: Button Function Description Back button Returns to the previous screen or closes the active window or keyboard. Home button Displays the Home screen. Recent apps button Opens a list of recently used applications.
Quick Start 1.2. CHARGING & COMMUNICATION 1.2.1. CHARGE MOBILE POS The main battery may not be charged to full for shipment. When you first receive the kit package, you will need to charge the main battery to full before using the mobile POS. You may use the Snap-on Charging Cable or Charging Cradle along with a power adapter to charge the mobile POS.
HERA51 Mobile POS USE SNAP-ON CHARGING CABLE The Snap-on Charging Cable provides a convenient way to charge your mobile POS. 1) Fasten the Snap-on Charging Cable to the lower end of the mobile POS. 2) Connect the other end of the cable to a USB port or the adaptor. 3) Fix the adapter plug onto the adapter, and plug in into an electrical outlet. While the device battery is being charged, the LED indicators on mobile POS will indicate charging status.
Quick Start USE CHARGING CRADLE The Charging Cradle can charge your mobile POS and a spare battery at the same time: Presents charging compartment for mobile POS and spare battery Provides micro USB socket on the back for charging Supports USB Host Mode via a USB OTG cable Completes charging in approximately 5 hours Adapter input AC 100-240V, 50/60Hz; output DC 5V, 2A.
HERA51 Mobile POS 1.2.2. WIRED DATA TRANSMISSION Use the Snap-on cable to connect the mobile POS to your PC for data transmission. 1) Connect your device to the computer with the supplied Snap-on cable. 2) Swipe down from the status bar to reveal Notifications Drawer. 3) Tap “USB charging this device” to enter USB options. “Transfer files” is set by default to transfer all types of files between your device and PC.
Quick Start 1.2.3 USING WIRELESS NETWORKS The mobile POS supports widely applied wireless technologies including Bluetooth v4.1 & v2.1+EDR, 802.11 a/b/g/n/ac, and is able to send/receive data in real time in an efficient way. Select GSM/GPRS/EDGE/WCDMA/HSPA/HSPA+/LTE CAT 6 modules embedded for a total wireless solution for data and voice communication.
HERA51 Mobile POS Chapter 2 USING THE HERA51 MOBILE POS This chapter walks you through the fundamental usage and features of this device. IN THIS CHAPTER 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Battery ...................................................................... 31 Memory ..................................................................... 43 Touch Screen ............................................................. 54 Notifications ...............................................................
Using the HERA51 Mobile POS 2.1. BATTERY Main Battery The mobile POS is powered by a rechargeable 3.8V / 4000 mAh Li-ion battery pack. It takes approximately 4 hours to charge it to full from the power adaptor (for the first time charging the main battery, please charge it for at least 8 to 12 hours). However, the charging time may vary by your working condition. Spare Battery A spare battery pack is provided as an accessory.
HERA51 Mobile POS 2.1.1. BATTERY STATUSINDICATORS The main battery pack is the only power source for the mobile POS to work. Therefore, when the main battery level goes low, you need to replace the battery pack with a charged one or charge it as soon as possible. Most of all, you should backup important data on a regular basis. By checking the battery status icon on Status Bar, you can tell the battery level remaining in the main battery. Main battery is fully charged.
Using the HERA51 Mobile POS Note: When the mobile POS is fully charged and battery level reaches 100%, the battery icon will change from to to indicate charging is completed. Warning: (1) Once the battery level drops below 15%, the low battery notification will be displayed on the screen. (2) Data loss with RAM may occur when battery level is low. Always save data before the battery runs out of power or keep a fresh battery for replacement.
HERA51 Mobile POS 2.1.2. MONITOR BATTERY LEVEL MAIN BATTERY LEVEL The main battery is the only source that feeds the mobile POS to work. It also supplies the backup battery on the main board in order to retain the data stored in DRAM. When main battery level gets low, recharge it or replace it as soon as possible. Most critically, back up the important data from time to time to protect your work. To check main battery level: Tap App Drawer (All Apps) | Settings | Battery .
Using the HERA51 Mobile POS BATTERY SAVER MODE You can have the Battery saver mode automatically turned on when the main battery gets low. This mode will limit the use of location services, vibration and most background processing data. Once Battery saver is enabled, the title bar of your screen will turn red. On Battery screen, simply switch on “Battery saver” or tap on it to enter “Battery saver” page to switch it on and set choose when to have this mode automatically activated.
HERA51 Mobile POS BATTERY OPTIMIZATION With Battery optimization enabled for the applications, you can make sure they stay inactive when your device is idle or when they have not been used for days. 1) On Battery screen, tap More and then select “Battery optimization”. 2) On the dropdown list, select “All apps”, all the applications will be optimized by this function by default.
Using the HERA51 Mobile POS LOW BATTERY ALERT The mobile POS prompts a warning notification reminding you to charge the main battery when the main battery level drops to 15% and 5%. In the meantime, the device’s status LED indicator will blink red. Opening Notifications Drawer, you will also see this warning appearing on the notifications list; you may turn on Battery Saver Mode, connect the mobile POS to an external power source, or replace the main battery pack as soon as possible.
HERA51 Mobile POS 2.1.3. REPLACE MAIN BATTERY When main battery level is low, follow the steps below to replace the main battery. SHUT DOWN TO REPLACE THE MAIN BATTERY Shut the device down to replace the main battery, please: 1) Make sure the sub battery (backup battery) and the new main battery are fully-charged. 2) Press and hold the power button on the side of the mobile POS. 3) Tap “Power off” in the pop-up menu. The mobile POS will power off.
Using the HERA51 Mobile POS BATTERY SWAP HERA51 mobile POS's backup battery supplies system power during battery swap. When the battery (with cover) is removed, the system will enter suspend mode and not wake up until battery cover is put back and the power button is pressed. Please refer to “Low Sub Battery Alert” to make sure the sub battery is fully charged before battery swap process.
HERA51 Mobile POS 2.1.4. POWER MANAGEMENT For any portable device, power management is a critical issue especially when you are on the road. Below are some tips to help you save battery power. Warning: Using backlight, wireless connectivity, and peripheral devices on battery power will substantially reduce battery power. Bring an additional main battery pack with you on the road. End wireless connections (such as Bluetooth transmission, WLAN, WWAN, NFC and GPS) which are not in use.
Using the HERA51 Mobile POS ENTER AIRPLANE MODE You can enable Airplane mode to have all the wireless radios (including call functions, data connections such as Bluetooth, Wi-Fi and 3G/4G) on your mobile POS turned off, which will considerably reduce the power consumption of your battery. To enter Airplane mode: 1) Use two fingers to swipe down from the top of the screen to open Quick Settings menu.
HERA51 Mobile POS 2.1.5. BATTERY TEMPERATUREANOMALY High ambient temperature or keeping using HERA51 mobile POS while charging might results in battery temperature rises. HERA51 mobile POS will automatically suspend charging battery or shut down for safety purpose. Once the battery temperature cools down to normal temperature, battery charging could be proceeded again. Using HERA51 mobile POS under low-temperature environment may cause the device shut down automatically.
Using the HERA51 Mobile POS 2.2. MEMORY Flash Memory (ROM) 16GB flash memory for storing the OS (Android 8.1 Oreo) and custom application programs. Random Access Memory (RAM) 2GB RAM for storing and running programs, as well as storing program data. Expansion Slot The mobile POS is equipped with one SD card slot which can accommodate a micro SD card, a microSDHC, or a microSDXC card.
HERA51 Mobile POS 2.2.1. CHECK MEMORY USAGE The memory manager can offer a glance of how the device is using its RAM. ENABLE DEVELOPER OPTION To check the memory usage, you have to enable “Developer 1) Go to App Drawer (All Apps) | Settings Option” : |About Phone. 2) Tap on “Build number” 7 times to enable it. During the process, you’ll see a prompt with a countdown reading “You are now X steps way from being a developer.
Using the HERA51 Mobile POS CHECK MEMORY USAGE to enter memory manager screen. On the main screen, it tells you not only the used and free memory space of the RAM, but how your pattern of usage has impacted the device’s overall performance. To figure out how the system and apps have been taking up the memory over a longer period, tap the dropdown list to choose a different time span.
HERA51 Mobile POS 2.2.2. MANAGE STORAGE SPACE To your Android device, the SD card can serve as an extension of your device’s internal storage (which comes as 16 GB of flash memory to store the OS, applications and files) other than a portable storage place. Go to App Drawer (All Apps) | and external storage spaces. Settings | Storage to check usage of the internal By default, all the videos, photos and downloaded files are directly saved to the device’s internal storage.
Using the HERA51 Mobile POS SET UP SD CARD AS PORTABLE STORAGE Using SD card as a portable device allows you to treat it as a USB disk, by swapping it between your Android device and the computer to easily transfer files. This is quite handy when there is a need to offload files that are taking up too much storage space. When this device is connected with PC, the disk content is readable from PC client: On Storage screen, this disk can be managed separately.
HERA51 Mobile POS To start: 1) Insert the SD card. A notification icon indicating that an SD card is detected will be shown in the status bar; swipe down from the status bar and tap on “SET UP”. 2) Tap “Use as portable storage” and then “NEXT”. 3) When the setting is completed, tap “DONE”. 4) Swipe down from the status bar to reveal Notifications Drawer, and you will find a notification indicating that the SD card is for transferring photos and media; tap “EXPLORE” to check its content.
Using the HERA51 Mobile POS TRANSFER PHOTOS & MEDIA BETWEEN THE DEVICE & PC To transfer photos and media between this device and PC when the mounted SD card is set as portable storage, please: 1) Connect your mobile POS with PC with supplied USB cable. 2) Swipe down from the status bar to reveal Notifications Drawer, and tap “USB charging this device” to enter USB options menu. 3) Choose “Transfer files”, and now you will find the disk content is readable from PC client.
HERA51 Mobile POS CONVERT THE SD CARD TO INTERNAL STORAGE 1) You can always convert the SD Card from portable storage to internal storage. On Storage screen, tap the SD card. Before you start, make a backup of the files on this disk if you would like to keep them. 2) On SD card content screen, tap More and then tap “Storage settings”. 3) By selecting “Format as internal”, the device will eventually format this SD card into a specific file format only readable by this device.
Using the HERA51 Mobile POS SET UP SD CARD AS INTERNAL STORAGE Using SD card as internal storage allows you to extend your existing device storage and to store huge applications. This SD card will be reformatted and encrypted with a file format that is not readable by another device. Therefore, it is essential that you back up important files on this SD card in advance.
HERA51 Mobile POS To start: 1) Insert the SD card. A notification will pop up indicating that an SD card is detected tap “SET UP”. 2) Tap “Use as internal storage” and then “NEXT”. 3) Tap “ERASE & FORMAT” to format this card. 4) You will then be asked whether to move media files to this new SD card; make your choice and then tap “Next”. 5) When the setting is completed, tap “DONE”.
Using the HERA51 Mobile POS CONVERT THE SD CARD TO PORTABLE STORAGE 1) You can always convert the SD Card from internal storage to portable storage. On Storage & USB, tap the SD card. Before you start, make a backup of the files on this disk if you would like to keep them. 2) On SD card content screen, tap More and then tap “Format as portable”. 3) Tap “Format” to have this SD card re-formatted into a file type inaccessible by other devices. 4) When the formatting is completed, tap “DONE”.
HERA51 Mobile POS 2.3. TOUCH SCREEN The mobile POS comes with a 4.7” transmissive LCD with 1280 by 720 pixels resolution (HD). The LED backlight of the screen, which helps ease reading under dim environments, can be controlled manually and automatically. Warning: DO NOT use any pointed or sharp objects to move against the surface of the screen. 2.3.1. SCREEN BRIGHTNESS Go to App Drawer (All Apps) | Settings | Display | Brightness level.
Using the HERA51 Mobile POS 2.3.2. SCREENROTATION By default, the device automatically rotates the screen to when you turn the device sideways. To switch this function on or off: 1) Go to App Drawer (All Apps) | Settings | Display 2) Tap Advanced for more display settungs, and switch on or off Auto-rotate screen. Please note that if Auto-rotate screen is switched off, the display orientation might be portrait or landscape depending on the screen display orientation when you switch it off.
HERA51 Mobile POS OR Use two fingers to swipe down from the top of the screen to open Quick Settings menu and tap the Auto rotate icon to enable screen rotation. This quick setting method allows you to temporarily enter landscape mode to enhance your typing experience by using a wide keyboard. To enable Home screen rotation, please make sure Auto Rotation is enable.
Using the HERA51 Mobile POS REMOVE AUTO-RITATE FROM QUICK SETTINGS MENU & DISPLAY SETTINGS You can remove the Auto-rotate switch icon on Quick Settings possibility of accidentally turning on the auto-rotation function: menu to minimize the 1) Use two fingers to swipe down from the top of the screen to open Quick Settings menu. button to get into Edit page; tap on and hold the Auto-rotate switch icon, and 2) Click drag it to the below area and then release it.
HERA51 Mobile POS Go to App Drawer (All Apps) | Settings | Accessibility and switch off Auto-rotate screen. By doing so, the auto-rotation option will be hidden in Settings | Display . Note: Auto-rotation is not supported for certain applications. Without enabling “Allow Home Screen Rotation”, auto-rotation is inapplicable in Home Screen and App Drawer screen.
Using the HERA51 Mobile POS 2.3.3. SCREENTIMEOUT SETTINGS Go to App Drawer (All Apps) | Settings | Display Select the time lapse for screen timeout. 59 | Advanced | Sleep.
HERA51 Mobile POS 2.3.4. TEXT SIZE & DISPLAY SIZE To change text size, please go to App Advanced | Font size. Drawer (All Apps) | Settings Tap the small A icon or the large A icon Default, Large and Largest. | to select the font size between Small, | Display Go to App Drawer (All Apps) | Settings and tap the plus icon Default.
